tire pressure SUZUKI GRAND VITARA 2002 2.G Service Owner's Manual

YH4
GRAND
VITARA
5-8 BRAKES
4) When fluid pressure in the cylinder is almost depleted, retigh-
ten bleeder plug.
5) Repeat this operation until there are no more air bubbles in hy-
draulic line.
6) When bubbles stop, depress and hold brake pedal and tighten
bleeder plug.
For tightening torque specification of air bleeder plug, re-
fer to ªTIGHTENING TORQUE SPECIFICATIONº in this
section.
7) Then attach bleeder plug cap.
8) After completing bleeding operation, apply fluid pressure to
pipe line and check for leakage.
9) Replenish fluid into reservoir up to specified level.
10) Check brake pedal for ªsponginessº. If found spongy, repeat
entire procedure of bleeding.

YH4
GRAND
VITARA
1. Air bleeder plug
2. Weight
3. Attachment2
ªLº
BRAKES 5-13
FLUSHING BRAKE HYDRAULIC SYSTEM
It is recommended that entire hydraulic system be thoroughly
flushed with clean brake fluid whenever new parts are installed in
hydraulic system.
Periodical change of brake fluid is also recommended.
FLUID PRESSURE TEST(if equipped with
LSPV)
Test procedure for LSPV assembly is as follows.
Before testing, confirm the following.

Fuel tank is filled with fuel fully.

Vehicle is equipped with spare tire, tools, jack and jack handle.
1) Stop vehicle on level floor and place approximately about
200 kg (441 lbs) weight on rear housing so that rear axle weight
800 kg (1764 lb).
Rear axle weight ªLº: 800 kg (1764 lb)
2) Install special tool to front and rear brake.
NOTE:
Special tool should be connected to breather of front (driv-
er's side brake) and rear brakes.
Special Tool
Front brake
(A): 09956-02310
(B): 09952-46510 (Attachment for vehicle with SUMITOMO
ELECTRIC brake caliper)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
Rear brake
(A): 09956-02310
(B): 09952-36310 (Attachment for thread diameter 7 mm of
bleeder plug) or
09952-46510 (Attachment for thread diameter 8 mm of
bleeder plug)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
NOTE:

Special tool (B) is used instead of thread diameter 10 mm
attachment of special tool (A).
So remove the attachment from (A) and install (B) as
shown in figure.

For vehicle with TOKICO brake caliper, use the attach-
ment included in special tool (A).

For identification of brake caliper type, refer to GENERAL
DESCRIPTION in SECTION 5B.

YH4
GRAND
VITARA
GOOD
NO GOOD
BRAKES 5-15
6) Upon completion of fluid pressure test, bleed brake system and
perform brake test.
BOOSTER OPERATION CHECK
There are two ways to perform this inspection, with and without a
tester. Ordinarily, it is possible to roughly determine its condition
without using a tester.
NOTE:
For this check, make sure that no air is in hydraulic line.
INSPECTION WITHOUT TESTER
Check Air Tightness
1) Start engine.
2) Stop engine after running for 1 to 2 minutes.
3) Depress brake pedal several times with the same load as in ordi-
nary braking and observe pedal travel. If pedal goes down deep
the first time but its travel decreases as it is depressed the se-
cond and more times, air tightness is obtained.
4) If pedal travel doesn't change, air tightness isn't obtained.
NOTE:
If defective, inspect vacuum lines and sealing parts, and re-
place any faulty part.
When this has been done, repeat the entire test.

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.