check engine SUZUKI GRAND VITARA 2002 2.G Service Manual PDF

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
1. Drain plug
2. Propeller shaft
1. Dipstick (G16 / J20)
2. Dipstick (H25)
7B1-60 AUTOMATIC TRANSMISSION (4 A / T)
LEVEL CHECK AT ROOM TEMPERATURE
The fluid level check at room temperature performed after repair or
fluid change before test driving is just preparation for level check of
normal operating temperature. The checking procedure itself is the
same as that described previously. If the fluid level is between FULL
COLD and LOW COLD, proceed to test drive. And when the fluid
temperature has reached the normal operating temperature, check
fluid level again and adjust it as necessary.
FLUID CHANGE
1) Lift up vehicle.
2) With engine is cool, remove drain plug from oil pan and drain A / T
fluid.
3) Install drain plug.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Lower vehicle and fill proper amount of an equivalent of DEX-
RON
-III.
5) Check fluid level according to procedure described under LEV-
EL CHECK NORMAL OPERATING TEMPERATURE.
Fluid specification
An equivalent of DEXRON
-III
Fluid capacity
When draining
from drain plug
hole
2.5 liters (5.28/4.40 US/lmp.pt.)
When
overhauling
6.9 liters (14.58/12.14 US/lmp.pt.)
for G16
7.1 liters (15.00/12.50 US/lmp.pt.)
for J20 / H25

YH4
GRAND
VITARA
1. Radiator
2. Inlet hose (Outlet from oil cooler)
3. Outlet hose (Inlet to coil cooler)
4. Converter housing
5. Outlet hose
6. Inlet hose
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
G16 / J20
H25
1. A / T throttle cable
2. Stopper
3. Inner cable
4. A / T assemblyR100 mm
(3.94 in.)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-61
OIL COOLER HOSES
When replacing them, be sure to note the followings.

to replace clamps at the same time.

to insert hose as far as its limit mark.

to clamp hose securely.
A / T THROTTLE CABLE
ADJUSTMENT
1) Pull inner cable by force of 2 N (0.2 kg, 0.45 lb) or less to be no
slack of inner cable with A / T throttle cable curved as shown in
the figure.
2) Fix stopper to inner cable with clearance ªcº.
Clearance ªcº : 0.8 ± 1.5 mm (0.03 ± 0.06 in.)
3)For G16 / J20 engines
a) Check clearance ªcº. If it is out of specifications, adjust it by
turning cable adjusting nut.
Clearance ªcº : 0.8 ± 1.5 mm (0.03 ± 0.06 in.)
b) Tighten lock nut securely.
For H25 engine
a) Warm up engine and transmission to normal operating tem-
perature.
b) Make sure that accelerator cable is adjusted as specified.
c) With throttle valve closed, check clearance ªcº which should
be within the following specification.
Clearance ªcº : 0.8 ± 1.5 mm (0.03 ± 0.06 in.)
If it is out of specification, adjust it by turning cable adjusting nut.

YH4
GRAND
VITARA
7B1-64 AUTOMATIC TRANSMISSION (4 A / T)
1. A / T vehicle (output) speed sensor
ªNº reference
line
Center line on
manual valve shaft
G16 / J20
1. Service wire
2. PCM connectors disconnected
Switch
position
TRANSMISSION RANGE SWITCH (SENSOR)
INSPECTION & ADJUSTMENT
1) Shift select lever to ªNº range.
2) Check that center line on manual valve shaft and ªNº reference
line on switch are aligned. If not, loosen switch bolt and align
them.
3) Check that engine starts in ªNº and ªPº ranges but it doesn't start
in ªDº, ª2º, ªLº or ªRº range. Also, check that back-up lamp lights
in ªRº range.
4) If faulty condition cannot be corrected by adjustment, discon-
nect transmission range switch coupler and check that continu-
ity exists as shown by moving select lever.
Terminal No.54982310765498231076
P
R
N
D
2
L
A / T OUTPUT SPEED SENSOR
INSPECTION
Check A / T output speed sensor for resistance between terminals
of sensor or PCM coupler.
A / T output speed sensor
resistance value : 387 ± 473
at 20
C, 68
F
O / D CUT SWITCH
INSPECTION
Check O / D cut switch for operation referring to step 4 of Diag. Flow
Table B-2 in this section.
If malfunction is found, replace.
SOLENOID VALVES
(Shift solenoid valves & TCC solenoid valve)
INSPECTION
With couplers of PCM disconnected and using service wire as
shown at the left, check each solenoid valve for clicking sound.
G16 / J20 Engines
Shift solenoid valve - A (#1)C51-1-2
Shift solenoid valve - B (#2)C51-1-1
TCC (Lock-up) solenoid valveC51-1-8

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-65
1. Drain plug
2. Propeller shaft
1. Oiler (with transmission fluid)
2. Solenoid valve
3. BatteryA: Hole (Should be dry)
B: Exhausting fluid Terminal Arrangement of PCM Coupler
(Viewed from harness side)
WITH BATTERY VOLTAGE WITHOUT BATTERY VOLTAGE
H25 Engine
Shift solenoid valve ± A (#1)C51-1-6
Shift solenoid valve ± B (#2)C51-1-1
TCC (Lock-up) solenoid valveC51-1-2
REMOVAL
1) Pull out dipstick and lift up vehicle.
2) With engine cooled, remove drain plug from oil pan and drain
A / T fluid.
3) Install drain plug with gasket.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Remove exhaust pipe bracket and disconnect front propeller
shaft from front differential (if equipped).
5) Remove oil pan bolts.
6) Remove oil pan.
7) Remove oil tubes.
8) Remove solenoid valve No.1 (shift solenoid valve A and B) or so-
lenoid valve No.2 (TCC solenoid valve).
OPERATION CHECK
Whenever shift solenoid valves and TCC (lock-up) solenoid valve
are removed from transmission, verify their valve function physical-
ly before they are reinstalled.
1) Apply oiler to solenoid valve and give compression by hands
and then check to be sure that transmission fluid from oiler does
not come out of holes in solenoid valve when battery voltage is
not conducted.
2) Under the same conditions as above, conduct battery voltage
and then make sure that fluid comes out with vigor.
NOTE:

If fluid does not come out with vigor in above step 2 in-
spection, do not re-use that solenoid valve.

Figure at the left shows shift solenoid valve check.
Check TCC solenoid valve also in the same way.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-67
1. Oil cooler pipes
2. Union gaskets
3. Pipe bolt
OIL COOLER PIPES
REMOVAL
1) Lift up vehicle.
2) Make sure to wash dirt off from around pipe joints.
3) With engine is cool, loosen oil cooler pipe union bolts with oil out-
let union locked and remove oil cooler pipes from oil outlet
unions and hoses.
NOTE:
To avoid fluid leakage, plug open ends of oil outlet unions
and hoses right after they are disconnected.
INSTALLATION
1) Use new union gaskets and connect oil cooler pipes to oil outlet
unions.
2) Connect hoses to pipes and clamp them securely.
3) Tighten union bolts to specified torque with oil outlet union
locked.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
4) Tighten pipe bolt securely.
5) Check A / T fluid level according to procedure described in ªFluid
Levelº section.
Add if necessary.
6) Check for fluid leakage after warming up A / T.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-77
ªAº, (d)
1. Drive plate
2. Torque converter
3. Case right stiffener (if equipped)
4. Automatic transmissionTightening torque
(a): 50 N´m
5.0 kg-m
36.5 lb-ft
(b): 65 N´m
6.5 kg-m
47.0 lb-ft
(c): 85 N´m
8.5 kg-m
61.5 lb-ft
(d): 78 N´m
7.8 kg-m
56.5 lb-ft
1. Automatic transmission
2. Transfer (4WD)
3. Engine rear mounting
4. Engine rear mounting member Tightening torque
(a): 50 N´m (5.0 kg-m, 36.5 lb-ft) ªAº: Sealant 99000-31110
REMOUNTING
WARNING:
When moving transmission assembly with torque convert-
er equipped in it, be sure to keep it horizontal. Tilting it with
its front facing down may allow converter to fall off. Where-
by an injury may result.
For remounting, reverse dismounting procedure. Use specified
torque as given below and left.
Tightening torque
N.mkg-mlb-ft
Exhaust No.1 pipe to manifold
bolts or nuts505.036.5
Muffler to exhaust No.2 pipe
nuts606.043.5
Universal joint flange bolts and
nuts505.036.5

Oil filler tube bolts

Select cable bracket bolts232.317.0

Clamp wiring harness and hoses securely.

Refer to ªSelect Cableº section for adjusting procedure of select
cable.

Refer to ªA / T Throttle Cableº section for tuning of A / T throttle
cable.

Follow fluid level check procedure for refilling automatic transmis-
sion fluid and its level adjusting.

Connect battery, and confirm that engine and transmission func-
tion acceptably.

When remounting drive plate, use specified bolts.

YH4
GRAND
VITARA
1. Wood block
2. Dash panel
t: 45 mm / 1.8 in.
H: 200 mm / 8 in.
W: 100 ± 150 mm / 4 ± 6 in.
1. Transmission jack
2. Engine rear mounting member
3. Gear shift lever case
4. Bolt
TRANSFER 7D-5
TRANSFER ASSEMBLY
Dismounting and remounting of transfer and transmission together
as a unit is described in Section 7A for Manual Transmission or 7B1
for Automatic Transmission, but it is also possible to dismount and
remount transfer assembly by itself as described below.
DISMOUNTING
IN ENGINE ROOM
1) Disconnect negative (±) cable from battery.
2) Remove distributor assembly (if equipped).
3) Place wood block between engine and dash panel so that it
serves as stopper when engine, transmission and transfer unit
hangs down as rear mounting member is removed.
CAUTION:
Make sure to use wood block to prevent contact which
may occur between dash panel and CMP sensor case
(G16), CMP sensor (J20) or intake manifold (H25), and fan
and shroud.
IN CABIN
1) Remove console box.
2) Remove shift lever of transmission and transfer.
ON LIFT
1) Drain transfer oil.
2) Remove rear propeller shaft.
3) Remove front propeller shaft.
4) Disconnect exhaust center pipe.
5) Disconnect speed sensor coupler.
6) Place transmission jack and remove mounting member.
7) Lower transmission jack gradually and check to ensure that
wood block serves as stopper between engine and dash panel.
8) Remove bolts for gear shift lever case.
9) Pull off breather hose.

YH4
GRAND
VITARA
1. Bolt
2. Transfer assembly
1. Bolt
2. Engine rear mounting3. Transfer assembly
1. Bolt
2. Transfer assembly
3. Transmission jack
7D-6 TRANSFER
IN CABIN
Remove gear shift lever case and then remove transfer center case
bolt.
ON LIFT
1) Remove transfer mounting (engine rear mounting) by removing
bolts.
2) Apply transmission jack to transfer to support it.
3) Remove couplers for 4WD / 4WD-LOW switches lead.
4) Remove transfer front case bolts.
5) With transfer assembly supported with transmission jack, slide
it rearward and when it is apart from transmission, lower it.
REMOUNTING
For remounting, reverse dismounting procedure described above,
noting following.

Be sure to use specified torque for tightening.

Clamp wiring and breather hose securely.

Clamp shift lever boot securely.

Fill specified gear oil by specified amount.

Connect battery and check for function.

YH4
GRAND
VITARA
7E-6 DIFFERENTIAL (FRONT)
STEPACTIONYESNO
1Turn ON ignition switch (but engine at stop) and
check malfunction indicator lamp.
Does lamp light up?Go to step 2.A trouble has
occurred at some
place. Repair it
referring to
MALFUNCTION
INDICATOR LAMP
(ªCHECK ENGINEº
LAMP) CHECK in
DIAGNOSIS of
SECTION 6.
2Check 4WD switch circuit.
Turn ignition switch ON and check that voltage
between terminal C51-2-18 and terminal C51-3-17
(ground) for G16 / J20 (terminal C51-1-11 and terminal
C51-3-26 (ground) for H25) is as follows.

When transfer shift lever is in N or 2H: 10 ± 14 V

When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?Go to step 3.Check 4WD switch
(refer to SECTION
7A), ªB / Orº and ªBº
circuits of 4WD
switch.
If OK, substitute a
known-good ECM
(PCM) and recheck.
3Check power supply.
1) Turn ignition switch ON.
2) Check voltage between C51-2-7 and C51-3-17
(ground) for G16 / J20 (C51-1-15 and C51-3-26
(ground) for H25). The check results should be as
follows.

When transfer shift lever is in N or 2H: 0 ± 1 V

When transfer shift lever is in 4L or 4H: 10 ± 14 V
Is the check result satisfactory?Go to step 4.Check ªRº circuit. If
it is OK, substitute a
known-good ECM
(PCM) and recheck.
4Check air pump assembly circuit.
1) Check for proper connection to air pump
assembly at all terminals.
2) Turn ignition switch ON.
3) Check voltage between C51-2-27 and C51-3-17
(ground) for G16 / J20 (C51-1-18 and C51-3-26
(ground) for H25). The check result should be as
follows.

When transfer shift lever is in 2H or N: 0 ± 1 V

When transfer shift lever is in 4L or 4H
(more than 4 seconds after shifted to 4L or 4H):
10 ± 14 V
Is the check result satisfactory?Go to step 5.Check air pump
assembly referring
to ªON-VEHICLE
SERVICEº, and then
ªPº circuit.
If OK, substitute a
known-good ECM
(PCM) and recheck.
5Check 4WD indicator lamp circuit.
1) Turn ignition switch ON.
2) Check voltage between E61-19 and C51-3-17
(ground) for G16 / J20 (C51-1-7 and C51-3-26
(ground) for H25). The check result should be as
follows.

When transfer shift lever is in 2H or N: 10 ± 14 V

When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?4WD control system
is in good condition.Check ªOr / Bº circuit
(including indicator
lamp and
combination meter).
If OK, substitute a
known-good ECM
(PCM) and recheck.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-7
1
1. ECM (PCM); viewed from harness side
4WD CONTROL CIRCUIT INSPECTION
Voltage Check [G16 and J20 engine models]
Check for input or output voltage (voltage between each circuit and
body ground) of ECM (PCM) with ECM (PCM) connector con-
nected and ignition switch turned ON.
TER-
MINALCIRCUITWIRE
COLORNORMAL
VOLTAGECONDITION
E6110 ± 14 VTransfer shift lever: 2H or NE61-
194WD Indicator lampOr / B0 ± 1 V4 seconds after transfer shift lever shifted
to 4H or 4L
C51 2Air pump assembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-7(Pump motor and release
valve)R10 ± 14 V1 seconds after transfer shift lever shifted
to 4H or 4L
C51-24WD switchB/Or10 ± 14 VTransfer shift lever: 2H or N
-184WD switchB/Or0 ± 1 VTransfer shift lever: 4H or 4L
C51-
3-17GroundB/Bl0 ± 1 V±
C51 2Airpumpassembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-27
Air um assembly
(pressure switch)P10 ± 14 V4 seconds after transfer shift lever shifted
to 4H or 4L