Engine diagram SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.

YH4
GRAND
VITARA
5E1-20 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
TABLE ± E EBD WARNING LAMP (BRAKE WARNING LAMP) CHECK-LAMP
COMES ªONº STEADY
CIRCUIT DESCRIPTION
EBD warning lamp (brake warning lamp) is controlled by parking brake switch, brake fluid level switch and ABS
control module / hydraulic unit assembly through lamp driver module in combination meter. Refer to ªTABLE-Aº for
circuit diagram.
STEP
ACTIONYESNO
11) Make sure that:

Parking brake is completely released.Go to step 2.Release parking
brake completely

Brake fluid level is upper than the minimum level.
Are the check results OK?and / or replenish
brake fluid.
2Does ªABSº warning lamp come on?Perform ªTABLE Bº
previously
outlined.Go to step 3.
31) Disconnect ABS hydraulic unit / control module
connector.
2) Check for proper connection to ABS hydraulic unit /
control module connector at terminals ªA26º.
3) If OK, apply chocks to wheels and select gear in neutral
position (P range for A / T).
4) Keep brake pedal depressed and start engine.
Release parking brake.
5) Connect terminal ªA26º of disconnected connector to
ground using service wire.
Does EBD warning lamp (brake warning lamp) turn off?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.ªBrº circuit open.
If wire and
connection are
OK, replace
combination
meter.

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Vehicle speedUpshift
Downshift
Throttle valve opening
Vehicle speed
Throttle valve opening
TCC ON
TCC OFF 4th
gear
3rd
gear(km / h)
(km / h)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-11
AUTOMATIC GEAR SHIFT DIAGRAM
Automatic shift schedule as a result of shift control is shown below. In case that select lever is shifted to L at a higher
than 52 km / h or 33 mile / h speed for G16 engine (45 km / h or 28 mile / h for J20 engine, 55 km / h or 34 mile / h for
H25 engine), 2nd or 3rd gear is operated and then down shifts to 1st at a speed lower than that. No up shift is
available in L.
The same as, the select lever is shifted to 2 at a higher than 102 km/h (64 mile/h) speed for G16/J20 engines (105
km / h or 65 mile / h for H25 engine), 3rd gear is operated and then down shifts to 2nd at a speed lower than that.
Power Mode For G16 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle49
(30)94
(58)153
(95)124
(77)85
(53)43
(27)
Closed throttle18
(11)36
(23)48
(30)40
(25)29
(18)7
(4)

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Vehicle speedUpshift
Downshift
Throttle valve opening
Vehicle speed
Throttle valve opening
TCC ON
TCC OFF 4th
gear3rd
gear(km / h)
(km / h)
7B1-12 AUTOMATIC TRANSMISSION (4 A / T)
Normal Mode For G16 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle45
(28)94
(58)136
(85)124
(77)74
(46)39
(24)
Closed throttle14
(9)32
(20)45
(28)35
(22)29
(18)7
(4)

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Throttle valve opening
Vehicle speedUpshift
Downshift
Throttle valve opening
Vehicle speed3rd
gear
4th
gear
TCC ON
TCC OFF(km / h)
(km / h)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-13
Power Mode For J20 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle50
(31)98
(61)Ð135
(84)84
(52)46
(29)
Closed throttle18
(11)33
(21)50
(31)44
(27)26
(16)8
(5)

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Upshift
Downshift
Throttle valve opening
Vehicle speed
Throttle valve opening
3rd
gear
4th
gear
TCC ON
TCC OFF
Vehicle speed(km / h)
(km / h)
7B1-14 AUTOMATIC TRANSMISSION (4 A / T)
Normal Mode For J20 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle50
(31)98
(61)147
(91)135
(84)84
(52)42
(26)
Closed throttle11
(7)27
(17)40
(25)37
(23)24
(15)8
(5)

YH4
GRAND
VITARA
Gear Shift Diagram
TCC Lock-up Diagram
Throttle valve opening
Vehicle speedUpshift
Downshift
Throttle valve opening
Vehicle speedTCC ON
TCC OFF 3rd
gear
4th
gear(km / h)
(km / h)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-15
Power Mode For H25 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle48
(30)99
(62)160
(99)150
(93)90
(56)41
(25)
Closed throttle16
(10)30
(19)45
(28)38
(24)24
(15)7
(4)

YH4
GRAND
VITARA
7B1-16 AUTOMATIC TRANSMISSION (4 A / T)
Gear Shift Diagram
TCC Lock-up Diagram
Throttle valve opening
Vehicle speed
Throttle valve opening
Vehicle speedUpshift
Downshift
TCC ON
TCC OFF 3rd
gear
4th
gear(km / h)
(km / h)
Normal Mode For H25 EngineUnit: km / h
(mile/h)
Shift
Throttle opening
1
22
33
44
33
22
1
Full throttle48
(30)99
(62)160
(99)150
(93)90
(56)41
(25)
Closed throttle11
(7)27
(17)40
(25)35
(22)21
(13)7
(4)

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-31
Brake pedal Released Depressed
Voltage 0 VBattery
voltage
DIAGNOSTIC FLOW TABLE A-1 (NO TCC LOCK-UP OCCURS)
SYSTEM DESCRIPTION
PCM turns TCC solenoid OFF under any of the following conditions.

Brake pedal switch: ON

4WD LOW switch: ON

Cruise control module: TCC OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor, its
circuit or engine cooling
system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-8 (G16 / J20 engines) or C51-1-2 (H25
engine) terminal of PCM coupler and ground.

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Brake pedal released.

Drive vehicle with TCC ON condition
referring to ªTCC lock-up diagramº in
this section.
Is it battery voltage?Faulty TCC solenoid
valve, its circuit or
transmission.Go to Step 4.
4Is vehicle equipped with H25 engine?Go to Step 5.Go to Step 6.
5Brake switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-31 terminal of PCM coupler
terminal and ground.
Is the result as specified?Go to Step 6.Faulty brake pedal switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.

O / D cut switch: ON

4WD LOW switch: ON

Cruise control module: O / D OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.

O / D cut switch OFF (ªO / D OFFº lamp OFF).

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.