MAIN RELAY SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Check contact tension by inserting and removing
just once.
2. Check each terminal for bend and proper alignment.
GENERAL INFORMATION 0A-15
INTERMITTENT AND POOR CONNECTION
Most intermittent are caused by faulty electrical connections or wir-
ing, although a sticking relay or solenoid can occasionally be at
fault. When checking it for proper connection, perform careful
check of suspect circuits for:

Poor mating of connector halves, or terminals not fully seated in
the connector body (backed out).

Dirt or corrosion on the terminals. The terminals must be clean
and free of any foreign material which could impede proper termi-
nal contact.
However, cleaning the terminal with a sand paper or the like is
prohibited.

Damaged connector body, exposing the terminals to moisture
and dirt, as well as not maintaining proper terminal orientation
with the component or mating connector.

Improperly formed or damaged terminals.
Check each connector terminal in problem circuits carefully to en-
sure good contact tension by using the corresponding mating ter-
minal.
If contact tension is not enough, reform it to increase contact ten-
sion or replace.

YH4
GRAND
VITARA
1A-4 HEATER AND VENTILATION
FOR LH VEHICLE
FOR RH VEHICLE
1. From ignition switch 1
2. From ignition switch 2
3. From blower fuse
4. Head light relay
5. To A / C controller6. Blower motor relay
7. Blower motor switch
8. Blower resistor
9. Blower motor
10. To ECM11. To illumination controller
(if equipped) or body ground
12. Mode control actuator
13. Mode control switch
14. From main fuse15. TAIL fuse 15 A
16. IG METER fuse 20 A
17. HEATER fuse 30 A
18. REAR DEFG fuse 15 A
19. Drive circuit
WIRING CIRCUIT

YH4
GRAND
VITARA
1. Blower motor main relay
2. Blower motor
3. Blower motor resistor
4. Blower motor switch
5. A / C controller
6. ECM
7. Heater mode control switch
8. Evaporator temperature sensor
9. Refrigerant pressure switch10. Compressor relay
11. Compressor
12. Condenser cooling fan relay
13. Condenser cooling fan
14. Fuse box
15. A / C fuse 25 A
16. Ignition switch
17. Main fuse box
18. Battery main fuse 80 A19. Battery
20. Generator
21. Ignition main fuse 60 A
22. Heater/A/C main fuse 60 A
23. Ignition / meter fuse 20 A
24. Rear defogger fuse 15 A
25. Heater fuse 30 A
26. Compressor thermal switch
(only IWATA production vehicle)
FOR LH VEHICLE
1B-16 AIR CONDITIONING (OPTIONAL)
WIRING CIRCUIT

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-17
1. Blower motor main relay
2. Blower motor
3. Blower motor resistor
4. Blower motor switch
5. A / C controller
6. ECM
7. Heater mode control switch
8. Evaporator temperature sensor
9. Refrigerant pressure switch
FOR RH VEHICLE
10. Compressor relay
11. Compressor
12. Condenser cooling fan relay
13. Condenser cooling fan
14. Fuse box
15. A / C fuse 25 A
16. Ignition switch
17. Main fuse box
18. Battery main fuse 80 A19. Battery
20. Generator
21. Ignition main fuse 60 A
22. Heater/A/C main fuse 60 A
23. Ignition / meter fuse 20 A
24. Rear defogger fuse 15 A
25. Heater fuse 30 A
26. Compressor thermal switch
(only IWATA production vehicle)

YH4
GRAND
VITARA
1B-20 AIR CONDITIONING (OPTIONAL)
A / C CONTROLLER VOLTAGE VALUES TABLE
TerminalWireCircuitMeasurement
groundNormal valueCondition
AC1-1B/WController main
power supplyGround to
engine (Fig. B)10 ± 14 voltsIgnition switch ON with engine
stopped
AC1-2B/YController main
groundGround to body
(Fig. A)± 0.4 ± 0 voltEngine running
AC1 4Or
Refrigerant
p
ressure switchGround to
0 ± 1 volt
Refrigerant pressure within 225 kPa
(2.3 kg / cm
2, 32.7 psi) to 2548 kPa
(26 kg / cm
2, 370 psi) with engine
running
AC1-4Orpressure switch
inputengine (Fig. B)
10 ± 14 volts
Refrigerant pressure below
196 kPa (2.0 kg / cm
2, 28 psi) or
above 3140 kPa (32 kg / cm
2, 455 psi)
with engine running
AC1 7G/B
A / C switch input
and / or defroster
Ground to
8 ± 14 volts
Blower fan motor switch and A / C or
defroster position switch (see NOTE)
ON with engine running
AC1-7G/Bposition switch
input (see NOTE)engine (Fig. B)
0 ± 1.5 volts
Blower fan motor switch or A / C or
defroster position switch (see NOTE)
OFF with engine running
AC1 9Gr/W
Signal input from
ECM (A / C ON
Ground to10 ± 14 voltsApprove of A / C ON
AC1-9Gr/W(
permission
signal)engine (Fig. B)0 ± 1 voltA / C ON forbid
AC1-13Y/B
Signal output to
ECM (A / C ON
request signal)Ground to engine
(Fig. B)0 ± 1.5 volts
Blower fan motor switch and A / C or
defroster position switch (see NOTE)
ON with engine running at evaporator
thermistor temperature input more
than approx. 2.5
C (less than 2.5 V
(5840
)) and refrigerant pressure
switch is ON
10 ± 14 voltsExcept the above-mentioned with
engine running
AC1-16P
Compressor
magnet clutch
relay outputGround to engine
(Fig. B)0 ± 1 volt
Blower fan motor switch and A / C or
defroster position switch ON with
engine running at evaporator
thermistor temperature input more
than approx. 2.5
C (less than 2.5 V
(5840
)), refrigerant pressure
switch ON and signal input from ECM
ON
10 ± 14 voltsExcept the above-mentioned with
engine running

YH4
GRAND
VITARA
5-6 BRAKES
ConditionPossible CauseCorrection
Brake warning light
turns on after
engine start
Parking brake applied.

Insufficient amount of brake fluid.

Brake fluid leaking from brake line.

Brake warning light circuit faulty.

Malfunctioning EBD system, if equipped
with ABS.Release parking brake and check
that brake warning light turns off.
Add brake fluid.
Investigate leaky point, correct it and
add brake fluid.
Repair circuit.
Check system referring to
ªDIAGNOSISº of ABS section.
Brake warning light
turns on when
brake is applied
Brake fluid leaking from brake line.

Insufficient amount of brake fluid.Investigate leaky point, correct it and
add brake fluid.
Add brake fluid.
Brake warning light
fails to turn on
even when parking
brake is applied
Bulb burnt out.

Brake warning light circuit open.Replace bulb.
Repair circuit.
ABS warning light
does not turn on
for 2 sec. after
ignition switch has
turned ON
Bulb burnt out.

ABS warning light circuit open, if equipped
with ABS. (including check relay)Replace bulb.
Check system referring to
ªDIAGNOSISº of ABS section.
ABS warning light
remains on after
ignition switch has
turned on for 2 sec.
Malfunctioning ABS, if equipped with ABS.Check system referring to
ªDIAGNOSISº of ABS section.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-15
1. Battery
2. Main fuses
3. Ignition switch
4. Circuit fuses
5. ABS hydraulic unit / control module
5-1. Terminal arrangement for ABS hydraulic unit /
control module assembly
5-2. ABS fail-safe relay (Solenoid valve relay)
5-3. ABS pump motor relay
5-4. Pump motor
5-5. Solenoid valves
6. ªABSº warning lamp
7. Right-rear wheel speed sensor
8. Left-rear wheel speed sensor
9. Right-front wheel speed sensor
10. Left-front wheel speed sensor
11. Data link connector
12. Diagnosis connector
13. Stop lamp
14. Stop lamp switch
15. PCM (ECM+TCM) or ECM
16. G sensor (For 4WD model only)
17. 4WD switch (For 4WD model only)
18. 4WD indicator lamp (For 4WD model only)
19. 4WD controller (If equipped)
20. EBD warning lamp (Brake warning lamp)
21. Combination meter
22. Parking brake switch
23. Brake fluid lever switch
24. Warning lamp driver moduleWire colorB : Black
B / Bl : Black / Blue
B / O : Black / Orange
B / W : Black / White
Bl : Blue
Bl /B : Blue / Black
Bl / O : Blue / Orange
Br : Brown
G : Green
G / B : Green / Black
G / W : Green / White
Lg : Lightgreen
Lg / B : Lightgreen / Black
O / B : Orange / Black
O / G : Orange / Green
O / W : Orange / White
P : Pink
P / B : Pink / Black
V / G : Violet / Green
W / BI : White / Blue
W / G : White / Green
W / Y : White / Yellow
Y : Yellow
Y / B : Yellow / Black
SYSTEM CIRCUIT
TERMINALCIRCUIT
A1Right-rear wheel speed sensor (+)
A2Right-front wheel speed sensor (±)
A3Right-front wheel speed sensor (+)
A4G sensor ground (For 4WD model only)
A5ÐÐÐ
A6ÐÐÐ
A7Idle up signal
A8Diagnosis switch terminal
A9Stop lamp switch
A10Ground (For ABS control module)
A11ABS fail-safe relay
A12Right-rear wheel speed sensor (±)
A13Left-front wheel speed sensor (±)
A14G sensor signal (For 4WD model only)
A15ÐÐÐ
A16ÐÐÐ
A17ªABSº warning lamp
A18Left-rear wheel speed sensor (+)
A19Left-rear wheel speed sensor (±)
A20Left-front wheel speed sensor (+)
A21ÐÐÐ
A22Data link connector
A23ÐÐÐ
A244WD switch (For 4WD model only)
A25Ignition switch
A26ªEBDº warning lamp
A27ABS pump motor relay
A28Ground (For ABS pump motor)

YH4
GRAND
VITARA
5E1-16 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
-1. Main fuse
-2. Ignition switch
-3. Circuit fuse for IG
-4. ªABSº warning lamp
-5. ABS hydraulic unit / control
module assembly
5-1. Fail-safe relay
5-2. To solenoid valves and
pump motor relay
(ABS hydraulic unit)
-6. Diagnosis connector
(Black connector)
6-1. Diag. switch terminal
6-2. Diag. ground terminal
-7. Combination meter
7-1. ABS lamp driver module
-8. ABS hydraulic unit/
control module connector
of harness
-9. EBD warning lamp
(Brake warning lamp)
-10. Parking brake switch
-11. Brake fluid level switch
TABLE ± A ªABSº WARNING LAMP CIRCUIT CHECK ± LAMP DOES NOT
COME ªONº AT IGNITION SWITCH ON
CIRCUIT DESCRIPTION
Operation (ON / OFF) of the ªABSº warning lamp is controlled by the ABS control module and ABS lamp driver mod-
ule.
If the Antilock brake system is in good condition, the ABS control module turns the ªABSº warning lamp ON at the
ignition switch ON, keeps it ON for 2 seconds only and then turns it OFF. If an abnormality in the system is detected,
the lamp is turned ON by ABS control module. Also, it is turned ON by ABS lamp driver module when the connector
of the ABS control module was disconnected.
INSPECTION
STEPACTIONYESNO
11) Turn ignition switch ON.
Do other warning lamp come ON?Go to step 2.Go to step 4.
21) Disconnect ABS hydraulic unit / control module
connector.
Does ABS warning lamp light with ignition switch ON?Replace ABS
hydraulic unit / control
module assembly.Go to step 3.
31) Remove combination meter.
Is bulb of ABS warning lamp in good condition?ªBl / Oº circuit shorted
to ground. If OK,
replace ABS
warning circuit (lamp
driver module).Replace bulb.
4Is IG fuse in good condition?Open in ªB / Wº wire to
combination meter or
poor connection.Repair and
replace.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-27
1. ABS hydraulic unit/
control module assembly
2. ABS hydraulic unit/
control module
connector
1. ABS hydraulic
unit / control
module connector
DTC 57 (DTC C1057) ± SOLENOID AND PUMP MOTOR POWER SOURCE
CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at terminal ( ªA11º and ªA27º) of the fail-safe and pump motor relays
circuit constantly with the ignition switch turned ON. When all solenoid circuit voltages are below the specified value
or the voltage at the terminal ªA27º became below the specified value while the pump motor is operating, this DTC
will be set. As soon as the voltage rises to the specified level, the set DTC will be cleared.
INSPECTION
STEPACTIONYESNO
1Check battery voltage. Is it about 11 V or higher?Go to step 2.Check charging
system referring
to ªCHARGING
SYSTEMº section.
2Check ABS main fuse and connection. Is it in good
condition?Go to step 3.Repair and / or
replace fuse.
31) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Check proper connection to ABS hydraulic unit /
control module connector at terminal ªA27º.
4) If OK, then measure voltage between connector
terminal ªA27º and body ground.
Is it 10 ± 14 V?Substitute a
known-good
ABS hydraulic
unit / control
module assembly
and recheck.ªW / Blº circuit open.
Fig. 1

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-29
1. Ignition switch
2. ABS hydraulic unit/
control module assembly
3. ABS hydraulic unit/
control module connector
of harness 2
1. ABS hydraulic
unit / control
module connector
DTC 63 (DTC C1063) ± ABS FAIL-SAFE RELAY CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at the terminal of the solenoid circuit constantly with the ignition
switch turned ON. Also, immediately after the ignition switch is turned ªONº, perform an initial check as follows.
Switch the fail-safe relay in the order of ON
OFF
ON and check if the voltage at 6 solenoid circuit terminals
changes to High
Low
High. If anything faulty is found in the initial check and when the voltage at all solenoid
circuit terminals is low with the ignition switch turned ON and ABS not operated, this DTC will be set.
INSPECTION
STEPACTIONYESNO
1Check battery voltage. Is it about 11 V or higher?Go to step 2.Check charging
system referring
to ªCHARGING
SYSTEMº section.
2Check ABS main fuse and connection. Is it in good
condition?Go to step 3.Repair and / or
replace fuse.
31) Ignition switch OFF.
2) Disconnect ABS hydraulic unit / control module
connector. (See Fig. 1)
3) Check proper connection to ABS hydraulic unit /
control module at terminal ªA11º.
4) If OK, then measure voltage between connector
terminal ªA11º, and body ground.
Is it 10 ± 14 V?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.ªW / Blº circuit open
or short to ground.
Fig. 1