brake lights SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
MAINTENANCE AND LUBRICATION 0B-25
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to ªHIº position for this check.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSG, SH or SJ (Refer to engine oil viscosity chart in item 1-4)
Engine coolant (Ethylene glycol
base coolant)ªAntifreeze / Anticorrosion coolantº
Brake fluidDOT 3
Manual transmission oilRefer to Section 7A or 7A1Transfer oilRefer to Section 7A or 7A1.
Differential oil (front & rear)Refer to Section 7E or 7F.
Automatic transmission fluid and
Power steering fluidRefer to Section 3B1 or 7B1.
Door hingesEngine oil or water resistance chassis greaseHood latch assemblyEngine oil or water resistance chassis grease
Key lock cylinderSpray lubricant

YH4
GRAND
VITARA
5-10 BRAKES
BRAKE PEDAL PLAY CHECK
Pedal play should be within specification. If out of specification,
check brake light switch for proper installation position and adjust
if necessary.
Also check pedal shaft bolt and master cylinder pin installation for
looseness and replace if defective.
Pedal play ªdº: 1 ± 8 mm (0.04 ± 0.32 in.)
BRAKE FLUID LEVEL CHECK
Be sure to use particular brake fluid either as indicated on reservoir
cap of that vehicle or recommended in owner's manual which
comes along with that vehicle.
Use of any other fluid is strictly prohibited.
Fluid level should be between MIN and MAX lines marked on reser-
voir.
When warning light lights sometimes during driving, replenish fluid
to MAX line.
When fluid decreases quickly, inspect brake system for leakage.
Correct leaky points and then refill to specified level.
CAUTION:
Do not use shock absorber fluid or any other fluid which
contains mineral oil. Do not use a container which has been
used for mineral oil or a container which is wet from water.
Mineral oil will cause swelling and distortion of rubber parts
in hydraulic brake system and water mixed into brake fluid
will lower fluid boiling point. Keep all fluid containers
capped to prevent contamination.
BRAKE HOSE AND PIPE CHECK
The brake hose assembly should be checked for road hazard dam-
age, for cracks and chafing of the outer cover, for leaks and blisters.
A light and mirror may be needed for an adequate inspection. If any
of the above conditions are observed on the brake hose, it is neces-
sary to replace it.
Inspect the pipe for damage, cracks, dents and corrosion. If any de-
fect is found, replace it.
MASTER CYLINDER CHECK
Check for a cracked master cylinder casting or brake fluid around
the master cylinder. Leaks are indicated only if there is at least a
drop of fluid. A damp condition is not abnormal.

YH4
GRAND
VITARA
Diagnostic Trouble Code (DTC) Table 5E1-14. . .
System Circuit 5E1-15. . . . . . . . . . . . . . . . . . . . . . .
Table ± A ªABSº Warning Lamp Circuit
Check ± Lamp does not come ªONº
at ignition switch on 5E1-16. . . . . . . . . . . . . . . . . .
Table ± B ªABSº Warning Lamp Circuit
Check ± Lamp comes ªONº steady 5E1-17. . . .
Table ± C ªABSº Warning Lamp Circuit
Check ± The lamp flashes continuously
while ignition switch is on5E1-18 . . . . . . . . . . . . . .
Table ± D Code (DTC) is not Outputted
even with Diag. Switch Terminal
Connected to Ground 5E1-19. . . . . . . . . . . . . . . .
Table ± E EBD Warning Lamp (Brake
Warning Lamp) Check-lamp Comes
ªONº Steady 5E1-20. . . . . . . . . . . . . . . . . . . . . . . .
DTC 15 ± G Sensor Circuit 5E1-21. . . . . . . . . . . .
DTC 21, 22, 25, 26, 31, 32, 35 or 36
± Wheel Speed Sensor Circuit 5E1-23. . . . . . . .
DTC 41, 45 or 56 ± Solenoid Circuit 5E1-26. . . . .
DTC 57 ± Solenoid and Pump Motor
Power Source Circuit 5E1-27. . . . . . . . . . . . . . . .
DTC 61 ± ABS Pump Motor Circuit 5E1-28. . . . . .
DTC 63 ± ABS Fail-Safe Relay Circuit 5E1-29. . .
DTC 71 ± ABS Control Module 5E1-30. . . . . . . . .
ON-VEHICLE SERVICE5E1-31 . . . . . . . . . . . . . . . .
Precaution 5E1-31. . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS Hydraulic Unit Operation Check 5E1-31. . . .
ABS Hydraulic Unit / Control Module
Assembly 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic unit inspection 5E1-32. . . . . . . . . . . . . Removal 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-33. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 5E1-34. . . . . . . . . . . .
Output voltage inspection 5E1-34. . . . . . . . . . . .
Removal 5E1-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-35. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-35. . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Front Sensor Rotor 5E1-36. . . . . . . . . . . . . . . . . . .
Removal 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel Speed Sensor 5E1-37. . . . . . . . . . . .
Output voltage inspection 5E1-37. . . . . . . . . . . .
Removal 5E1-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-38. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-38. . . . . . . . . . . . . .
Installation 5E1-38. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sensor Rotor 5E1-39. . . . . . . . . . . . . . . . . . . .
Removal 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . .
G Sensor 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Transfer 4WD Switch 5E1-41. . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5E1-41 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5E1-42 . . . . . . . . . . . . . . . . . . . . . .
5E1-2 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
GENERAL DESCRIPTION
The ABS (Antilock Brake System) controls the fluid pressure applied to the wheel cylinder of each brake from the
master cylinder so that each wheel is not locked even when hard braking is applied. This ABS is a 4-wheel type
which controls the fluid pressure applied to the wheel cylinder of each of the four brakes to prevent each wheel
from getting locked.
The component parts of this ABS includes following parts in addition to those of the conventional brake system.

Wheel speed sensor which senses revolution speed of each wheel and outputs its signal.

In this ABS, ABS hydraulic unit (actuator assembly), ABS control module, pump motor relay and fail-safe relay
are combined as one component.

ABS control module which sends operation signal to ABS hydraulic unit to control fluid pressure applied to each
wheel cylinder based on signal from each wheel speed sensor so as to prevent wheel from locking.

ABS hydraulic unit which operates according to signal from ABS control module to control fluid pressure applied
to wheel cylinder of each of 4 wheels.

Fail-safe (solenoid valve) relay which supplies power to solenoid valve in ABS hydraulic unit and pump motor
relay.

Pump motor relay which supplies power to pump motor in ABS hydraulic unit.

ªABSº warning lamp which lights to inform abnormality when system fails to operate properly.

G sensor which detects body deceleration speed. (For 4WD model only)
This ABS is equipped with Electronic Brake force Distribution (EBD) system that controls a fluid pressure of rear
wheels to best condition, which is the same function as that of proportioning valve, by the signal from wheel sensor
independently of change of load due to load capacity and so on. And if the EBD system fails to operate properly,
the brake warning lamp lights to inform abnormality.

YH4
GRAND
VITARA
1. Diagnosis connector
(6 pins connector)
2. Ground terminal3. Diag. switch terminal
4. Service wire
5E1-6 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
ABS HYDRAULIC UNIT/CONTROL MODULE
ASSEMBLY
ABS control module is a component of ABS hydrauli unit / control
module assembly and has the following functions.
Self-Diagnosis Function
ABS control module diagnoses conditions of the system compo-
nent parts (whether or not there is any abnormality) all the time and
indicates the results (warning of abnormality occurrence and DTC)
through the ªABSº warning lamp as described below.
1) When ignition switch is turned ON, ªABSº warning lamp lights for
2 seconds to check its bulb and circuit.
2) When no abnormality has been detected (the system is in good
condition), ªABSº warning lamp turns OFF after 2 seconds.
3) When the vehicle starts to move after the ignition switch is turned
ON (more than one wheel speed sensor signals are inputted),
solenoid valves and motor of ABS hydraulic unit operate once
one after another for electrical check.
During this check, motor operation sound may be heard but that
means nothing abnormal.
4) When an abnormality in the system is detected, ªABSº warning
lamp lights and the area where that abnormality lies is stored in
the memory of EEPROM in ABS control module.
5) When Diag. switch terminal of diagnosis connector (monitor
connector) is grounded, the abnormal area is output as DTC. It
is indicated by flashing of ªABSº warning lamp. (Refer to the
table below. )
ABS WARNING LAMP
SYSTEM CONDITIONDiag. switch
terminal is not
groundedDiag. switch
terminal is
grounded
In good condi-
No trouble in
the pastOFFDTC 12g
tion at presentTrouble occur-
red in the pastOFFHistory DTC
Abnormality
exists at
No trouble in
the pastONCurrent DTC
exists at
presentTrouble occur-
red in the pastONCurrent and
history DTCs
For procedure to clear all DTC's, refer to the item ªDiagnostic
Trouble Code Clearanceº in this section.
Also ABS control module turns ON EBD warning lamp (brake warn-
ing lamp) depending on the trouble that detected by the module and
EBD warning lamp does not indicate DTC as well as ªABSº warning
lamp.
Fail-Safe Function
When an abnormality occurs (an abnormal DTC is detected), ABS
control module turns OFF the fail-safe relay which supplies power
to ABS hydraulic unit. Thus, with ABS not operating, brakes func-
tion just like the brake system of the vehicle not equipped with ABS.

YH4
GRAND
VITARA
Example: When right-front wheel speed sensor circuit opens (DTC 21)
1. Diagnosis connector
(6 pins connector)
2. Ground terminal3. Diag. switch terminal
4. Service wire
Voltmeter indicator
(or ªABSº warning
lamp)HIGH
(ON)
LOW
(OFF)
Time (sec.)
1. EBD warning lamp
(brake warning lamp)
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-11
EBD WARNING LAMP (BRAKE WARNING
LAMP) CHECK
NOTE:
Perform this check on a level place.
1) Turn ignition switch ON with parking brake applied.
2) Check that brake warning lamp is turned ON.
3) Release parking brake with ignition switch ON and check that
EBD warning lamp (brake warning lamp) goes off.
If it doesn't go off, go to ªTABLE-Eº in this section.
ªABSº WARNING LAMP CHECK
1) Turn ON the ignition switch.
2) Check that ªABSº warning lamp lights for about 2 seconds and
then goes OFF.
If anything faulty is found, advance to Diagnostic table ± A, B or
C.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
(USING ªABSº WARNING LAMP)
1) Using service wire, connect diag. switch terminal of diagnosis
connector to ground.
2) Turn ignition switch ON.
3) Read flashing of ªABSº warning lamp which represents DTC as
shown in example below and write it down. When more than 2
DTC's are stored in memory, deflection and flashing for each
DTC is repeated three times starting with the smallest DTC num-
ber in increasing order.
For details of DTC, refer to ªDTC Tableº.

YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-5
CLEARANCE, TAIL AND LICENCE PLATE LIGHTS
TroublePossible causeCorrection
All lights do not light
ªTAILº fuse blown

Lighting switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Some lights do not light
up
Bulb(s) blown

Wiring or grounding faultyReplace bulb(s)
Repair
BACK-UP LIGHTS
TroublePossible causeCorrection
Back-up lights do not
light
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Bulb blown

 
  
 switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace bulb
Replace switch
Repair
Back-up lights remains
ON
Back-up light switch or shift switch faulty

Wiring or grounding faultyReplace switch
Repair
BRAKE LIGHTS
TroublePossible causeCorrection
Brake lights do not light
up
ªSTOP / HORNº fuse blown (Hard Top
Model)
ªSTPº fuse blown (Canvas Top Model)

Bulb(s) blown

Brake light switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace bulb(s)
Adjust or replace switch
Repair
Brake lights stay on
Brake light switch faultyAdjust or replace switch
Only one light does not
light
Bulb blown

Wiring or grounding faultyReplace bulb
Repair
REAR FOG LIGHT (IF EQUIPPED)
TroublePossible causeCorrection
Rear fog light does not
come on
ªFOGº fuse blown

Rear fog light switch faulty

Lighting switch faulty

Wiring or grounding faulty

Bulb blownReplace fuse to check for short
Replace fog light switch
Replace switch
Repair
Replace bulb
INTERIOR LIGHTS
TroublePossible causeCorrection
Interior light (s) does (do)
not light up
Bulb(s) blown

ªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top Model)

Wiring or grounding faulty

Door switch faulty

Interior light switch faultyReplace bulb(s)
Replace fuse to check for short
Repair
Replace switch
Replace light assy
Front spot lights do not
light up
Bulb(s) blown

Wiring or grounding faulty

Spot light switch faultyReplace bulb(s)
Repair
Replace light assy

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-7
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
TroublePossible causeCorrection

All power doors are not
locked / unlocked by
both driver side door key
switch and power door
lock switch. But all
power doors are locked /
unlocked by keyless
entry transmitter

All power doors are not
locked / unlocked by
driver side door key
switch, power door lock
switch and keyless entry
transmitter

When power doors are
locked / unlocked by
keyless entry
transmitter, hazard
warning lights do not
flash
ªDOOR LOCKº fuse blown

Power door lock and keyless entry system
faultyReplace fuse to check for short
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
keyless entry transmitter
Code registration error

Transmitter battery dead

Transmitter faulty

Power door lock and keyless entry system
faultyRegister code
Replace battery
Replace transmitter
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
Although any door is
opened within 30 seconds
after power door(s)
unlocked by keyless entry
transmitter, all power
doors are locked again
automatically
Door switch faulty

Wiring harness connected to door switch
brakesReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator
Operation distance of
keyless entry is unstable
Transmitter battery dead

Transmitter faultyReplace battery
Replace transmitter