checking oil SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Full level mark (hole)
2. Low level mark (hole)
0B-10 MAINTENANCE AND LUBRICATION
NOTE:
Engine oil capacity is specified. However, note that the
amount of oil required when actually changing oil may
somewhat differ from the data in the table depending on
various conditions (temperature, viscosity, etc.).
7) Check oil filter and drain plug for oil leakage.
8) Start engine and run it for three minutes. Stop it and wait five min-
utes before checking oil level. Add oil, as necessary, to bring oil
level to FULL level mark on dipstick.
NOTE:
Step 1) ± 7) outlined above must be performed with ENGINE
NOT RUNNING. For step 8), be sure to have adequate ven-
tilation while engine is running.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug to drain coolant.
3) Remove reservoir, which is on the side of radiator, and drain.
4) Tighten plug securely. Also reinstall reservoir.
5) Fill radiator with specified amount of coolant, and run engine for
2 or 3 minutes at idle. This drives out any air which may still be
trapped within cooling system. STOP ENGINE. Add coolant as
necessary until coolant level reaches the filler throat of radiator.
Reinstall radiator cap.

YH4
GRAND
VITARA
1. Drain plug (Apply sealant)
2. Reverse idle gear shaft bolt (DO NOT LOOSEN IT)
3. Filler / level plug (Apply sealant)
1. Drain plug
2. Filler / level plug
Type 1
Type 2
1. Level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
0B-20 MAINTENANCE AND LUBRICATION
ITEM 6-10
Manual Transmission Oil Inspection and Change
Inspection
1) Inspect transmission case for evidence of oil leakage.
Repair leaky point if any.
2) Make sure that vehicle is placed level for oil level check.
3) Remove level plug of transmission.
4) Check oil level.
Oil level can be checked roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil.
5) Tighten level plug to specified torque.
Refer to Section 7A or 7A1 for installation and tightening torque.
Change
Change transmission oil with new specified oil referring to Section
7A or 7A1.
ITEM 6-11
Automatic Transmission Fluid Inspection and Change
Inspection
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to On-vehicle service in
Section 7B1 and be sure to perform it under specified conditions.
If fluid level is low, replenish specified fluid.

YH4
GRAND
VITARA
1B
AIR CONDITIONING (OPTIONAL) 1B-1
GENERAL DESCRIPTION1B- 3 . . . . . . . . . . . . . .
Identification of Refrigerating System 1B- 3. . . .
Refrigerant Flow of Air Conditioning
System 1B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Major Components and Location 1B- 5. . . . . . .
DIAGNOSIS1B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
General 1B- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis of Abnormal Noise 1B- 8. . . . . . . . . .
Quickly Checking of Refrigerant Charge
(If Equipped with Sight Glass) 1B-10. . . . . . . . .
Compression System Diagnosis 1B-11. . . . . . . .
Performance Diagnosis 1B-12. . . . . . . . . . . . . . .
Wiring Circuit 1B-16. . . . . . . . . . . . . . . . . . . . . . . .
Inspection of A / C Controller and Its
Circuits 1B-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT RECOVERY,
EVACUATION AND CHARGING1B-23 . . . . . . . .
Operation Procedure for Charging A / C
with Refrigerant 1B-23. . . . . . . . . . . . . . . . . . . . .
Recovery 1B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Evacuating 1B-25. . . . . . . . . . . . . . . . . . . . . . . . . .
Charging 1B-26. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Manifold Gauge Set 1B-29. . . . . . . . .
Leak-Testing Refrigerant System 1B-29. . . . . . .
Liquid Leak Detectors 1B-29. . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE1B-30 . . . . . . . . . . . . . . . .
Precaution 1B-30. . . . . . . . . . . . . . . . . . . . . . . . . . .
A / C Condenser Assembly 1B-33. . . . . . . . . . . . .
Condenser Cooling Fan Assembly 1B-35. . . . . .
SECTION 1B
AIR CONDITIONING (OPTIONAL)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CAUTION:
The air conditioning system of this vehicle uses refrigerant HFC-134a (R-134a).
None of refrigerant, compressor oil and component parts is interchangeable between two types of A / C:
one using refrigerant CFC-12 (R-12) and the other using refrigerant HFC-134a (R-134a).
Be sure to check which refrigerant is used before any service work including inspection and mainte-
nance. For identification between these two types, refer to the description in page 1B-2.
When replenishing or changing refrigerant and compressor oil and when replacing parts, make sure
that the material or the part to be used is appropriate to the A / C installed in the vehicle being serviced.
Use of incorrect one will result in leakage of refrigerant, damage in parts or other faulty condition.
For basic servicing method of the air conditioning system that is not described in this section, refer to AIR CONDI-
TIONING BASIC MANUAL (99520-02130).
CONTENTS

YH4
GRAND
VITARA
3C1
AIR BAG STEERING WHEEL AND COLUMN 3C1-1
GENERAL DESCRIPTION3C1- 2 . . . . . . . . . . . . .
DIAGNOSIS3C1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair Required after
Accident 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C1- 3 . . . . . . . . . . . . . . .
Service Precautions 3C1- 3. . . . . . . . . . . . . . . . .
Diagnosis and Servicing 3C1- 3. . . . . . . . . . . .
Disabling Air Bag System 3C1- 3. . . . . . . . . . .
Enabling Air Bag System 3C1- 3. . . . . . . . . . .
Handling and Storage 3C1- 3. . . . . . . . . . . . . .
Disposal 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Air Bag (Inflator) Module 3C1- 4. . . . . . . .
Steering Wheel 3C1- 6. . . . . . . . . . . . . . . . . . . . . . Centering Contact Coil 3C1- 6. . . . . . . . . . . . .
Contact Coil and Combination Switch
Assembly 3C1- 7. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Column 3C1- 9. . . . . . . . . . . . . . . . . . . .
Steering Lock Assembly (Ignition
Switch) 3C1-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Lower Shaft Assembly 3C1-15. . . . . . .
Checking Steering Column for Accident
Damage 3C1-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Steering Column Release
Lever 3C1-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3C1-18 . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C1-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3C1
AIR BAG STEERING WHEEL AND COLUMN
WARNING:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in air bag system section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintentional activation of the system
or could render the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
1. Drain plug
2. Propeller shaft
1. Dipstick (G16 / J20)
2. Dipstick (H25)
7B1-60 AUTOMATIC TRANSMISSION (4 A / T)
LEVEL CHECK AT ROOM TEMPERATURE
The fluid level check at room temperature performed after repair or
fluid change before test driving is just preparation for level check of
normal operating temperature. The checking procedure itself is the
same as that described previously. If the fluid level is between FULL
COLD and LOW COLD, proceed to test drive. And when the fluid
temperature has reached the normal operating temperature, check
fluid level again and adjust it as necessary.
FLUID CHANGE
1) Lift up vehicle.
2) With engine is cool, remove drain plug from oil pan and drain A / T
fluid.
3) Install drain plug.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Lower vehicle and fill proper amount of an equivalent of DEX-
RON
-III.
5) Check fluid level according to procedure described under LEV-
EL CHECK NORMAL OPERATING TEMPERATURE.
Fluid specification
An equivalent of DEXRON
-III
Fluid capacity
When draining
from drain plug
hole
2.5 liters (5.28/4.40 US/lmp.pt.)
When
overhauling
6.9 liters (14.58/12.14 US/lmp.pt.)
for G16
7.1 liters (15.00/12.50 US/lmp.pt.)
for J20 / H25

YH4
GRAND
VITARA
1. Heat wire
2. Tin foil
3. Tester probe
1. VoltmeterAt center
Good
Broken
wire
broken
wire
8D-16 WINDOWS, MIRRORS, SECURITY AND LOCKS
REAR WINDOW DEFOGGER (IF EQUIPPED)
INSPECTION
DEFOGGER SWITCH
Check for continuity between terminals at each switch position as
shown below.
If check result is not as specified, replace switch.
DEFOGGER WIRE
NOTE:

When cleaning rear window glass, use a dry cloth to wipe it
along wire direction.

When cleaning glass, do not use detergent or abrasive-con-
taining glass cleaner.

When measuring wire voltage, use a tester with negative
probe wrapped with a tin foil which should be held down on
wire by finger pressure.
1) Checking wire damage
a. Turn main switch ON.
b. Turn defogger switch ON.
c. Use a voltmeter to check voltage at the center of each heat
wire, as shown.
Voltage
Criteria
Approx. 5 VGood (No break in wire)
Approx. 10 V or 0 VBroken wire
If measured voltage is 10 V, wire must be damaged between
its center and positive end. If voltage is zero, wire must be
damaged between its center and ground.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-7
[INTERMITTENT TROUBLES]


There are cases where output of diagnostic output terminal
and / or malfunction indicator lamp indicate a diagnostic trouble
code representing a trouble which occurred only temporarily and
has gone. In such case, it may occur that good parts are replaced
unnecessarily. To prevent such accident, be sure to follow instruc-
tions given below when checking by using ªDiagnostic Flow
Tableº.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM / PCM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and / or malfunction indicator lamp indicate a
trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what malfunction indicator lamp and / or output of diag-
nostic output terminal indicate.
Only when they indicate trouble code again, substitute a known-
good ECM / PCM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.


There are cases where output of diagnostic output terminal and/
or Suzuki scan tool indicates a diagnostic trouble code represent-
ing a trouble which occurred only temporarily and has gone. In
such case, it may occur that good parts are replaced unnecessar-
ily. To prevent such accident, be sure to follow instructions given
below when checking by using ªDiagnostic Flow Tableº.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM / PCM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and/or Suzuki scan tool indicates a trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what Suzuki scan tool and/or output of diagnostic out-
put terminal indicates.
Only when they indicate trouble code again, substitute a known-
good ECM / PCM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.

YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-63
REPAIRS AND INSPECTIONS REQUIRED AFTER AN ACCIDENT
CAUTION:

All air bag system components, including the electrical harness (component mounting points), must
be inspected after an accident. If any components are damaged or bent, they must be replaced even
if air bag system activation did not occur.

Never use air bag system parts from another vehicle.

Do not attempt to service the parts below. Service of these parts is by replacement only.
± Driver/Passenger air bag (inflator) module
± Driver/Passenger seat belt pretensioner
± SDM
± Contact coil and combination switch assembly
± Air bag wire harness

Proper operation of the sensors and air bag system requires that any repairs to the vehicle structure
return it to its original production configuration.
CAUTION:
After detecting one time of such collision as to meet deployment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.
ACCIDENT WITH DEPLOYMENT ± COMPONENT
REPLACEMENT
Certain air bag system components must be replaced. Those com-
ponents are:

Driver and passenger air bag (inflator) modules
± Replace with new one.

Driver and passenger seat belt pretensioners
± Replace with new one as an assembly.

SDM after detecting such collision as to meet deployment condi-
tions
± Replace with new one.

YH4
GRAND
VITARA
10B-64 AIR BAG SYSTEM
ACCIDENT WITH OR WITHOUT DEPLOYMENT ± COM-
PONENT INSPECTIONS
Certain air bag and restraint system components must be in-
spected after any crash, whether the air bag deployed or not.
Those components are:

Steering column and shaft joints
± Check for length, damage and bend according to ªChecking
Steering Column for Accident Damageº in SECTION 3C1.

Steering column bracket and capsules
± Check for damage and bent.
If any faulty condition is found in above checks, replace faulty
part.

Steering wheel and driver air bag (inflator) module
± Check for damage or air bag (inflator) module fitness.
± Check trim cover (pad surface) for cracks.
± Check wire harness and connector for damage or tightness.
If any faulty condition is found in above checks, replace faulty
part.

Contact coil and combination switch assembly
± Check wire harness and connectors for damage or tightness.
± Check contact coil case for damage.
If any faulty condition is found in above checks, replace.

Instrument panel member and reinforcement
± Check for any distortion, bending, cracking or other damage.
If any faulty condition is found in above checks, replace.