gear box SUZUKI GRAND VITARA 2003 2.G Service User Guide

YH4
GRAND
VITARA
1. Steering gear box mounting bolts
1. Mark
2. Gear case
3. Pinion shaft
POWER STEERING (P / S) SYSTEM 3B1-15
7) Remove steering gear box mounting bolts and then remove
steering gear box from vehicle.
Steering gear box found to be in defective condition should be
replaced with a new one.
CAUTION:
Never disassemble P / S gear box. If perform this prohib-
ited service, it will affect original performance.
INSTALLATION
Reverse removal procedure for installation of steering gear box
noting the following points.

After confirming that front tire is in straight position, install steering
gear box to body temporarily. Next, with tie-rod end installed to
knuckle, set rack in position close to neutral. Then obtain the neu-
tral state by aligning match marks on pinion shaft and steering
gear case and insert steering lower joint into pinion shaft.
CAUTION:
Be sure to confirm that steering wheel and front tires
(wheels) are in straight position when inserting steering
lower joint into steering pinion shaft.

If a plug was put to disconnected pipe when removing steering
gear box, remove that plug before reconnecting pipe.

Use specified torque as given below.
Tightening Torque
(a): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
(b): 40 N
.m (4.0 kg-m, 29.0 lb-ft)
(c): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
(d): 55 N
.m (5.5 kg-m, 40.0 lb-ft)

After installation, be sure to fill specified power steering fluid and
bleed air.

Check toe setting. Adjust as required. (Refer to Front End Align-
ment.)

YH4
GRAND
VITARA
3B1-16 POWER STEERING (P / S) SYSTEM
1. Clip
2. Wire
Make marking here
RACK BOOT AND TIE-ROD (EXCEPT CANVAS
TOP LH MODEL)
REMOVAL
CAUTION:
Never disassemble tie-rod except for canvas top LH model.
Performing this prohibited service will affect original per-
formance.
1) Remove steering gear box by referring to ªPOWER STEERING
GEAR BOX ASSEMBLY REMOVALº in this section.
2) For ease of adjustment after installation, make marking of tie-rod
end lock nut position of tie-rod end thread.
3) Loosen tie-rod end lock nut and remove tie-rod end.
4) Remove boot wire and clip.
5) Remove boot from tie-rod.
INSTALLATION
1) Visually inspect that rack and rack end ball joint are free from dirt
or foreign matters. Clean thoroughly with cloth or such.
Position boot properly in grooves of gear case and tie-rod and
clamp it with wire and clip.
Wire should be new and should go around twice.
Pull its both ends together by screw driver or such and make
sure that the wire won't be crossed. Then twist the ends several
times, the twisted ends should be bent in the circumferential
direction.
After this, check to ensure that wire is tight and boot is free from
twist and dent.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-17
1. Tie-rod
2. Steering rack
3. Boot
4. Mark
1. Tie-rod lock washer
2. Tie-rod
3. Steering rack
4. Aluminium plate
5. Vise
1. Tie-rod
2. Mark
3. Lock nut
4. Tie-rod end
5. Knuckle
6. Nut
2) Install tie-rod end lock nut and tie-rod end to tie-rod. Position lock
nut to the mark made in removal.
3) Install steering gear box assembly by referring ªPOWER
STEERING GEAR BOX ASSEMBLY INSTALLATIONº in this
section.
After installation, fill specified P / S fluid and bleed air from sys-
tem. Then check toe setting and adjust as required.
RACK BOOT AND TIE-ROD
(FOR CANVAS TOP LH MODEL)
REMOVAL
1) Remove steering gear case, refer to ªPOWER STEERING
GEAR BOX ASSEMBLY REMOVALº in this section.
2) For ease of adjustment after installation, make marking of tie-rod
end lock nut position of tie-rod thread.
3) Loosen tie-rod end lock nut and remove tie-rod end.
4) Remove boot band and clip.
5) Remove boot from tie-rod.
6) Unbend washer (2 places), and remove tie-rod from rack.

YH4
GRAND
VITARA
3B1-18 POWER STEERING (P / S) SYSTEM
ªAº
1
1
1. Mark
1. Tie-rod lock washer
(A)
INSTALLATION
1) Install new tie-rod lock washer and tie-rod to rack.
2) Tighten tie-rod ball nut to specified torque.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
3) Bend lock washer 2 place at the flat part of tie-rod ball nut.
4) Apply grease to ªAº indicated in figure.
5) Position boot properly in grooves of gear case and tie-rod.
Check to ensure that boot is free from twist and dent.
6) Fasten boot with new clamp and clip securely.
Special Tool
(A): 09943-55010
7) Install tie-rod end lock nut and tie-rod end to tie-rod.
Position lock nut to marking made in removal.
NOTE:
When tie-rod was replaced, measure length ªAº on re-
moved tie-rod and use it on new replacement tie-rod so as
to position lock nut properly.
8) Install steering gear case. Refer to ªPOWER STEERING GEAR
BOX ASSEMBLY INSTALLATIONº in this section.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-19
Tightening Torque
(a): 60 N.m (6.0 kg-m, 43.5 lb-ft)
(b): 25 N.m (2.5 kg-m, 18.5 lb-ft)
(c): 55 N.m (5.5 kg-m, 40.0 lb-ft)
(d): 11 N.m (1.1 kg-m, 8.0 lb-ft)
(e): 35 N.m (3.5 kg-m, 25.5 lb-ft)
( f ): 40 N.m (4.0 kg-m, 29.0 lb-ft)
(g): 45 N.m (4.5 kg-m, 33.0 lb-ft)
1. Power steering pump assembly
2. Bracket
3. P / S fluid reservoir4. High pressure hose & pipe
5. Suction hose
6. Low pressure return hose7. Oil tank bracket
8. To P / S gear box
[G16 ENGINE MODEL]
[J20 ENGINE MODEL][H25 ENGINE MODEL]
POWER STEERING PUMP

YH4
GRAND
VITARA
3B1-26 POWER STEERING (P / S) SYSTEM
09915-77420
Oil pressure gauge
attachment and hose set09915-77410
Oil pressure gauge09943-55010
Boot clamp plier
TIGHTENING TORQUE SPECIFICATION
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Gear box mounting bolts555.540.0
Gear box cylinder pipe flare nuts292.921.0
Gear box low pressure pipe union bolt404.029.0
Gear box high pressure pipe union bolt353.525.5
Tie-rod end lock nut656.547.0
G16 Type engine555.540.0
Pump bracket boltJ20 Type engine252.518.5
H25 Type engine454.532.5
Pump union bolt606.043.5
Oil pump mount bolts252.518.5
Pipe clamp bolt / Reservoir bracket bolt111.18.0
Steering shaft joint bolt252.518.0
High pressure flare nuts404.029.0
Pump cover bolts232.317.0
Plug606.043.5
Pressure switch (Terminal)282.820
Suction connector bolt101.07.5
Tie-rod end nut484.835.0
Tie-rod (for canvas top LH model only)858.561.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUPER GREASE (A)
(99000-25010)
Oil seal lip of P / S pump pulley shaft
Power steering fluidAn equivalent of DEXRON
-III or
DEXRON
-II

To fill P / S fluid reservoir

Parts lubrication when installing
SPECIAL TOOL

YH4
GRAND
VITARA
5C-16 PARKING AND REAR BRAKE
1. Brake back plate
2. Cable cap
3. Parking brake cable
6) Install wheel cylinder, and tighten wheel cylinder bolts and
brake pipe flare nut (or nuts) to specified torque. (Refer to steps
1) to 4) of WHEEL CYLINDER INSTALLATION of this section.)
7) Install parking brake cable to brake back plate.
8) Install brake shoes, referring to steps 1) to 4) of BRAKE SHOE
INSTALLATION.
9) Install brake drum. Refer to steps 1) to 2) of BRAKE DRUM
INSTALLATION in this section.
10) Refill differential housing with new specified gear oil. Refer to
ªMAINTENANCE SERVICEº in Section 7E for refill.
11) Fill reservoir with brake fluid and bleed brake system. (For
bleeding operation, refer to BLEEDING BRAKES in Section 5.)
12) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
13) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-
to-shoe clearance.
Adjust parking brake cable. (For adjustment, refer to PARKING
BRAKE CHECK AND ADJUSTMENT in Section 5.)
14) Tighten rear center console box screws.
15) Check to ensure that brake drum is free from dragging and
proper braking is obtained. Then remove vehicle from hoist
and perform brake test (foot brake and parking brake).
16) Check each installed part for oil leakage.

YH4
GRAND
VITARA
7A
MANUAL TRANSMISSION (TYPE 1) 7A-1
TYPE 1
GENERAL DESCRIPTION7A- 1 . . . . . . . . . . . . . .
DIAGNOSIS7A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A- 3 . . . . . . . . . . . . . . . .
Gear Oil 7A- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A- 4. . . . . . . . . . . . . . . . . . .
Switches 7A- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A- 8. . . . . . . . . . . . . . . .
Dismounting of Trans. Unit 7A- 9. . . . . . . . . . . . .
Remounting of Trans. Unit 7A-12. . . . . . . . . . . . . Extension Case (2WD MODEL) 7A-13. . . . . . . .
Extension Case Oil Seal
(2WD MODEL) 7A-13. . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A-14 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A-14 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A-14 . . . . . .
SPECIAL TOOL7A-14 . . . . . . . . . . . . . . . . . . . . . . .
As the aluminum case is sealed with liquid type gas-
ket, it is necessary to use genuine sealant or its equiv-
alent on its mating surfaces when reassembling it.
Also, the case fastening bolts must be tightened to
specified torque by means of the torque wrench and
tightening over or below the specified torque should
be avoided.
The description under ON-VEHICLE SERVICE in this
section covers a part of the TYPE 2 manual transmis-
sion and the transfer. The transfer is next to the trans-
mission as well, but their gear boxes are independent
and each of them has its own drain and level / filler
plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A
MANUAL TRANSMISSION
(TYPE 1)
CONTENTS
GENERAL DESCRIPTION
The manual transmission consists of the input shaft,
main shaft, countershaft and reverse gear which are
installed in the aluminum case. Its gears are of for-
ward five speeds in synchro mesh and reverse one
speed in constant mesh system.
The main shaft gears are held by the needle bearings
and on them the synchronizer rings and synchronizer
sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.

YH4
GRAND
VITARA
1. Bolt
2. Console box
bracket
3. Boot cover
1. Boot No. 3
2. Boot cover
3. Boot No. 2
4. Control lever
5. Lever case
6. Control case cover
7. Boot No. 1
1. Transmission control
lever locating bolt
2. Transfer control lever
locating bolt
7A-4 MANUAL TRANSMISSION (TYPE 1)
SHIFT CONTROL LEVERS
REMOVAL
1) Remove 4 screws at the front and rear and 2 clips at the center
then take off front and rear center console boxes.
NOTE:
To remove clip, push in its center pin first.
2) Remove console box bracket by removing bolts and lift up boot
cover and boot No. 2.
3) Remove boot clamp and then remove boot No. 1 from transmis-
sion shift lever case.
4) With gear shift control case cover pushed down with fingers, turn
it to counter clockwise and take out shift control lever.
5) Take out transfer shift control lever in similar manner as de-
scribed above.
INSPECTION AND INSTALLATION
1) Check shift control lever lower portion and control lever locating
sheet for excessive wear, and boot for damage. Correct or re-
place if necessary.
2) Apply grease to pivot portions and seat, then install shift control
lever.
ªAº: Grease 99000-25010
3) Perform above steps also for transfer shift control lever.
4) If control lever locating bolts (a) are replaced or retightened,
torque them as specified below.
Replacing of control lever locating bolts requires thread lock ce-
ment.
ªBº: Cement 99000-32020
Tightening Torque
(a): 17 N
.m (1.7 kg-m, 12.5 lb-ft)

YH4
GRAND
VITARA
7A1
MANUAL TRANSMISSION (TYPE 2) 7A1-1
TYPE 2
GENERAL DESCRIPTION7A1-1 . . . . . . . . . . . . . .
DIAGNOSIS7A1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A1-3 . . . . . . . . . . . . . . . .
Gear Oil 7A1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A1-4. . . . . . . . . . . . . . . . . . .
Switches 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A1-4. . . . . . . . . . . . . . . . Dismounting / Remounting of
Trans. Unit 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A1-4 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A1-5 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A1-5 . . . . . .
The manual transmission consists of the input shaft,
main shaft, counter shaft and reverse gear which are
installed in the aluminum and castings cases. Its
gears are of forward five speeds in synchro mesh and
reverse one speed in sliding idler gear arrangement
system.
The main shaft gears are held by the needle bear-
ings and on them the synchronizer rings and syn-
chronizer sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.As the aluminum and castings cases are sealed with
liquid type gasket, it is necessary to use genuine seal-
ant or its equivalent on its mating surfaces when reas-
sembling them. Also, the case fastening bolts must be
tightened to specified torque by means of the torque
wrench and tightening over or below the specified
torque should be avoided.
The description under ON-VEHICLE SERVICE in this
section covers the transfer partially which is next to
the transmission as well, but their gear boxes are in-
dependent and each of them has its own drain and
level / filler plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A1
MANUAL TRANSMISSION
(TYPE 2)
CONTENTS
GENERAL DESCRIPTION