Idle SUZUKI GRAND VITARA 2003 2.G Service Owner's Manual

YH4
GRAND
VITARA
7B1-46 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0741 TCC (LOCK-UP) SOLENOID VALVE PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While running in 2nd or 4th gear, D range, TCC control
of PCM does not agree with actual operation of trans-
mission TCC even though solenoid valve is electrically
in good condition.
(2 driving cycles detection logic)
TCC (lock-up) solenoid valve stuck

TCC control valve stuck

Valve body fluid passage clogged

TCC faulty
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool and check fuel level meter
indication is 1/4 or more.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Increase vehicle speed with D range, and check that gear position changes from 1st to 2nd and keep driving
about 20 mph, 30 km/h in 2nd of ªDº range for 10 seconds. (Throttle valve should be not at idle position and
the opening should be kept constant in this step.)
5) Keep driving about 50 mph, 80 km/h in 4th of ªDº range for 10 seconds.
6) Release accelerator pedal, decrease vehicle speed and stop vehicle.
7) Check pending DTC and DTC by using scan tool.
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2TCC solenoid valve operation check:
1) Check TCC solenoid valve operation referring to
ªSolenoid Valves Operation Checkº in this section.
Is it in good condition?Go to Step 3.Faulty TCC solenoid
valve.
3Valve body check:
1) Check valve body referring to ªUnit Repairº in this
section.
Is it in good condition?Faulty torque
converter.Faulty valve body.

YH4
GRAND
VITARA
1. Fluid pressure check hole
2. Oil pan
1. Oil pan
2. Exhaust pipe
7B1-54 AUTOMATIC TRANSMISSION (4 A / T)
LINE PRESSURE TEST
Purpose of this test is to check operating conditions of each part by
measuring fluid pressure in fluid pressure line. Line pressure test
requires following conditions.

Automatic fluid is at normal operating temperature (70 to 80C /
158 ± 176F).

Fluid is filled to proper level (between FULL HOT and LOW HOT
on dipstick).
1) Apply parking brake securely and place checks against wheels.
2) Attach oil pressure gauge to fluid pressure check hole in trans-
mission case.
Special Tool
(A): 09925-37810
CAUTION:
After attaching oil pressure gauge, check that not fluid
leakage exists.
3) Depress foot brake fully, run engine at idle and stall and then
check fluid pressure in ªDº or ªRº range.
CAUTION:
Do not continue running engine at stall speed longer than
5 seconds.
G16 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
5.1 ± 5.7 kg / cm2
73 ± 81 psi
At stall speed11.7 ± 13.2 kg / cm2
166 ± 188 psi
14.2 ± 16.7 kg / cm2
202 ± 237 psi
J20 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.8 ± 4.3 kg / cm2
54 ± 61 psi
5.3 ± 5.9 kg / cm2
75 ± 84 psi
At stall speed9.7 ± 11.2 kg / cm2
138 ± 159 psi
12.9 ± 15.5 kg / cm2
183 ± 220 psi
H25 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
6.6 ± 7.2 kg / cm2
94 ± 102 psi
At stall speed11.3 ± 12.7 kg / cm2
161 ± 181 psi
14.7 ± 22.7 kg / cm2
209 ± 323 psi

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-55
Check resultPossible cause
Line pressure higher
than standard level in
each range
Malfunctioning regulator valve

Malfunctioning throttle valve

Maladjusted A / T throttle cable
Line pressure lower than
standard level in each
range
Defective O/D clutch

Defective oil pump

Malfunctioning throttle valve

Malfunctioning regulator value

Maladjusted A / T throttle cable
Line pressure lower than
standard level only in ªDº
range
Fluid leakage from forward clutch

Defective O/D clutch

Leakage from ªDº range fluid pressure cir-
cuit
Line pressure lower than
standard level only in ªRº
range
Fluid leakage from direct clutch

Defective O/D clutch

Fluid leakage from reverse brake

Fluid leakage from ªRº range fluid circuit
Tightening torque of transmission case plug:
17 N.m (1.7 kg-m, 12.0 lb-ft)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at ªDº and ªRº ranges. Be sure
to perform this test only when transmission fluid is at normal operat-
ing temperature and its level is between FULL and LOW marks.
CAUTION:

Do not run engine at stall more than 5 seconds continu-
ously, for fluid temperature may rise excessively high.

After performing stall test, be sure to leave engine running
at idle for longer than 30 seconds before another stall test.
1) Apply parking brake and block wheels.
2) Install tachometer.
3) Start engine with select lever shifted to ªPº.
4) Depress brake pedal fully.
5) Shift select lever to ªDº and depress accelerator pedal fully while
watching tachometer. Read engine rpm quickly when it has be-
come constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed in ªRº range.

YH4
GRAND
VITARA
7B1-56 AUTOMATIC TRANSMISSION (4 A / T)
8) Stall speed should be within the following specification.
Stall speed: 2,100 ± 2,400 r / min. for G16 engine
2,300 ± 2,600 r / min. for J20 engine
2,300 ± 2,600 r / min. for H25 engine
Check result
Possible cause
Lower than standard
level
Faulty engine output

Defective torque converter
Higher than standard
level in ªDº range
Slippery O/D clutch

Slippery forward clutch

Malfunctioning O/D one-way clutch

Malfunctioning one-way clutch No. 2

Low line pressure
Higher than standard
level in ªRº range
Slippery direct clutch

Slippery reverse brake

Low fluid pressure

Slippery O/D clutch

Defective O/D one-way clutch
ROAD TEST
This test is to check if upshift and downshift take place at specified
speed while actually driving vehicle on a level road.
WARNING:

Carry out test in very little traffic area to prevent an acci-
dent.

Test requires 2 persons, a driver and a tester.
1) Warm up engine.
2) With engine running at idle, shift select lever ªDº.
3) Accelerate vehicle speed by depressing accelerator pedal grad-
ually.
4) While driving in ªDº range, check if gear shift occurs properly as
shown in Gear Shift Diagram in this section.
Test result
Possible cause
When 1
2 upshift fails to
occur1±2 shift valve stuck
When 2
3 upshift fails to
occur2±3 shift valve stuck
When 3
O/D upshift
fails to occur3±4 shift valve stuck
When gear shift point is in-
correct
Maladjusted throttle cable

Defective shift solenoid valve
-A or -B

1±2, 2±3 or 3±4 shift valve not
operating properly