short SUZUKI GRAND VITARA 2003 2.G Service Repair Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2003, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2003 2.GPages: 801, PDF Size: 12.15 MB
Page 720 of 801
YH4
GRAND
VITARA
10B-14 AIR BAG SYSTEM
DIAGNOSTIC TROUBLE CODE TABLE (Page 1 of 2)
EXAMPLE: WHEN DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH (CODE NO.21) IS SET
Turn ON
Turn OFF
0.30.3 1.0 3.0 3.0 Malfunction indicator lamp
(ªAIR BAGº warning lamp)Code No. 21 Code No. 21 Code No. 21
Time (sec.)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
12Normal±±±±±
15Resistance high
16Passenger
air bag
Resistance low
18
air bag
circuitShort to ground
19Short to power circuit
21Resistance high
Diagnose trouble
according to ªDiagnos-
tic Flow Tableºcorre-
22
Driver air bag
Resistance low
tic Flow Table corre-
sponding to each code
No.
24
g
circuitShort to ground
25Short to power circuit
31Power
source
Too high
32
source
voltageToo low
Page 721 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-15
DIAGNOSTIC TROUBLE CODE TABLE (Page 2 of 2)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
41Resistance high
42Driver
pretensionerResistance low
43circuit
(if equipped)Short to ground
44Short to power circuit
45Resistance highDiagnose trouble
di t ªDi
46Passenger
pretensionerResistance low
according to ªDiagnos-
tic Flow Tableº corre-
sponding to each code
47circuit
(if equipped)Short to ground
s onding to each code
No.
48Short to power circuit
51SDMFrontal crash detected
61ªAIR BAGº warning lamp circuit
71SDMInternal fault
NOTE:
When 2 or more codes are indicated, the lowest numbered code will appear first.
If a code not listed on the table is displayed, then the SDM is faulty.
Current DTC and history DTC can be identified by lighting and flashing of ªAIR BAGº warning lamp as
follows.
Current DTC is set.
(Abnormality exists at present.)History DTC is set only. (Faulty condi-
tion occurred once in the past but nor-
mal condition is restored at present.)
ªAIR BAGº warning lamp
after ignition switch ONRemains ON.Flashing 6 times and turns OFF.
ªAIR BAGº warning lamp
when grounding diagnosis
switch
Current DTC is displayed.History DTC is displayed.
However, if a multiple number of DTC's are set an even one of them is a current DTC, ªAIR BAGº warning
lamp remains on after ignition switch is turned ON. Therefore, it is not possible to identify any of them
as to whether it is a current one or a history one. (But use of scan tool (Tech 1) will make identification
possible.)
Page 722 of 801
YH4
GRAND
VITARA
7. SDM
7-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin 1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B: Air bag harness
10B-16 AIR BAG SYSTEM
TABLE A ± ªAIR BAGº WARNING LAMP COMES ªONº STEADY (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Ignition switch OFF.
2) Remove and inspect ªAIR BAGº fuse.
3) Is fuse good?Go to step 2.ªBI/Rº wire short to ground.
After repair, replace
ªAIR BAGº fuse.
21) Disconnect SDM.
2) Check proper connection to SDM at
terminal ªA16º.
3) If OK then check voltage between ªA16º
terminal of SDM connector and body
ground with ignition switch ON.
4) Is it 8 V or more?Go to step 3.ªBI/Rº wire (between
ªAIR BAGº fuse and SDM
connector) open ªBI/Bº wire
(between ignition switch and
ªAIR BAGº fuse) open or short
to ground.
31) Disconnect 16p connector from
combination meter, referring to Section
8C.
2) Check resistance between ªA5º terminal
of SDM connector and body ground.
3) Is resistance 1 k or more?Substitute a known-
good SDM and
recheck.ªBIº wire (between combina-
tion meter and SDM connec-
tor) short to ground.
Page 724 of 801
YH4
GRAND
VITARA
7. SDM
7-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin 1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B: Air bag harness
10B-18 AIR BAG SYSTEM
TABLE B ± ªAIR BAGº WARNING LAMP DOES NOT COME ªONº (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Set parking brake.
2) Note combination meter as ignition switch
is turned ON.
3) Does the ªBRAKEº indicator (warning lamp)
come ON?Go to step 2.ªB/Wº wire, ªIG.COIL
METERº fuse or J/B
(between ignition
switch and combination
meter) open or short to
ground.
21) With ignition switch OFF, disconnect SDM.
2) Check electrical connection check
mechanism (connection detection pin).
3) Is it in good condition?Go to step 3.Repair electrical
connection check
mechanism.
31) Disconnect SDM.
2) Check proper connection to SDM at
terminal ªA5º.
3) If OK then check voltage from ªA5º terminal of
SDM connector to body ground with ignition
switch ON.
4) Is it 9 V or more?Substitute a known-good
SDM and recheck.Go to step 4 on the
next page.
Page 725 of 801
YH4
GRAND
VITARA
(A)ªA5º
1. Combination meter connector (16p)
2. ªY / Gº wire terminal1. Connection detection pin
AIR BAG SYSTEM 10B-19
TABLE B ± ªAIR BAGº WARNING LAMP DOES NOT COME ªONº (Page 2 of 2)
STEPACTIONYESNO
41) Remove combination meter, referring to
SECTION 8C.
2) Check proper connection to combination
meter at terminal for ªAIR BAGº warning lamp
and to SDM at terminal ªA5º.
3) If OK then check resistance between ªY / Gº
wire terminal of combination meter connector
(16p) and ªA5º terminal of SDM connector.
4) Is resistance 1 or less?Go to step 5.Repair high resistance
or open in ªBIº or ªY / Gº
wire circuit (between
combination meter and
SDM).
51) Measure voltage from ªA5º terminal of SDM
connector to body ground with ignition switch
ON.
2) Is it 9 V or more?Repair short from ªBIº or
ªY / Gº wire circuit
(between combination
meter and SDM) to
power circuit.Go to step 6.
61) Remove and inspect ªAIR BAGº bulb.
2) Is bulb good?Substitute a known-good
combination meter and
recheck.Replace bulb.
Fig. for STEP 2 Fig. for STEP 3 and 5
Fig. for STEP 4
Special Tool
(A): 09932-76010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.
Page 726 of 801
YH4
GRAND
VITARA
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter7. Connection detection pin
8. SDM
8-1. ªAIR BAGº warning lamp driver circuit -5. ªAIR BAGº fuse in ªAIR BAGº fuse box
-6. ªAIR BAGº monitor coupler
6-1. Diagnosis switch terminal : Air bag harness
6±1 6
10B-20 AIR BAG SYSTEM
TABLE C ± ªAIR BAGº WARNING LAMP FLASHES (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Check ªAIR BAGº monitor coupler.
2) Is it connected diagnosis switch terminal and
ground terminal in ªAIR BAGº monitor coupler
by service wire?Remove service wire.Go to step 2.
21) With ignition switch OFF, disconnect SDM.
2) Measure resistance between ªA8º terminal of
SDM connector and body ground.
3) Is resistance 1 k or more?Substitute a known-good
SDM and recheck.Repair short from ªVº
wire circuit to ground.
Page 729 of 801
YH4
GRAND
VITARA
1. DLC
2. Scan tool1. ªW/Bº wire terminal
AIR BAG SYSTEM 10B-23
TABLE D ± SDM CANNOT COMMUNICATE THROUGH THE SERIAL DATA CIRCUIT
(Page 2 of 2)
STEPACTIONYESNO
21) Check if communication is possible by
trying communication with other
controller (ECM (or PCM), ICM or ABS
controller).
2) Is it possible to communicate with other
controller?Go to step 3.Repair open in common
section of serial data circuit
(ªW/Bº wire circuit) used by
all controllers or short to
ground or power circuit
which has occurred some-
where in serial data circuit
(ªW/Bº wire circuit).
31) With ignition switch OFF, disconnect
SDM and ªLamp, DLC and Monitor
Coupler Groundº (ªEº) connector.
2) Check proper connection at ªW/Bº wire
terminal for DLC in ªEº connector.
3) If OK, then check resistance between
ªW/Bº wire terminal in ªEº connector and
ªA4º terminal of SDM connector.
4) Is resistance 1 or less?Substitute a known-good
SDM and recheck.Repair high resistance or
open in ªW/Bº wire circuit
(in air bag harness).
Fig. for STEP 1 Fig. for STEP 3
Special Tool
(A): 09932-76010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.
Page 730 of 801
YH4
GRAND
VITARA
1. SDM
2. Passenger air bag (inflator) module: Shorting bar
: Air bag harness
10B-24 AIR BAG SYSTEM
CODE 15 ± PASSENGER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The combined resistance of the passenger air bag (inflator) module, harness wiring and connector terminal contact
is above a specified value for specified time.
Page 731 of 801
YH4
GRAND
VITARA
STEERING WHEEL1. Paper
AIR BAG SYSTEM 10B-25
CODE 15 ± PASSENGER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH (Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, disconnect
passenger air bag (inflator) module
connector behind the glove box.
2) Check proper connection to passenger air
bag (inflator) module at terminals in ªBº
connector.
3) If OK then connect Special Tool (B) to
passenger air bag (inflator) module
connector disconnected at the step 1).
4) With ignition switch ON, is DTC 15 current?Go to step 2.1) Ignition switch OFF.
2) Replace passenger
air bag (inflator)
module.
21) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at
terminals ªA2º and ªA3º.
3) Release shorting bar in SDM connector by
inserting a piece of paper, referring to the
figure below.
4) If OK then measure resistance between ªA2º
and ªA3º terminals with connected Special
Tool (B).
5) Is resistance 2.9 or less?Substitute a known-
good SDM and recheck.Repair high resistance
or open in ªYº or ªY/Rº
wire circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.
Page 732 of 801
YH4
GRAND
VITARA
1. SDM
2. Passenger air bag (inflator) module: Shorting bar
: Air bag harness
10B-26 AIR BAG SYSTEM
CODE 16 ± PASSENGER AIR BAG INITIATOR CIRCUIT RESISTANCE LOW (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The combined resistance of the passenger air bag (inflator) module, harness wiring and connector terminal contact
is below a specified value for specified time.