horn SUZUKI GRAND VITARA 2003 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2003, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2003 2.GPages: 801, PDF Size: 12.15 MB
Page 173 of 801
YH4
GRAND
VITARA
1. Steering wheel
2. Steering wheel pad
3. Screw
1. Steering shaft nut
1. Steering wheel
1. Lugs
2. Grooves
3. Alignment marks
STEERING WHEEL AND COLUMN 3C-3
ON-VEHICLE SERVICE
STEERING WHEEL
REMOVAL
1) Disconnect negative battery cable at battery terminal.
2) Remove steering wheel pad screw.
3) Remove steering wheel pad and disconnect horn harness.
4) Remove steering shaft nut.
5) Make alignment marks on steering wheel and shaft for a guide
during reinstallation.
6) Remove steering wheel with special tool.
Special Tool
(A): 09944-36011
CAUTION:
Do not hammer the end of the shaft. Hammering it will
loosen the plastic shear pins which maintain the column
length and impair the collapsible design of the column.
INSTALLATION
1) Install steering wheel to steering shaft with 2 lugs on combina-
tion switch fitted in two grooves in the back of steering wheel and
also aligning marks on steering wheel and steering shaft.
2) Tighten steering shaft nut to specified torque.
Tightening Torque
(a): 33 N
.m (3.3 kg-m, 23.5 lb-ft)
3) Connect horn harness and install steering wheel pad.
4) Tighten steering wheel pad screw.
5) Connect negative battery cable.
Page 188 of 801
YH4
GRAND
VITARA
1 11
1. Mounting bolt
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
3C1-4 AIR BAG STEERING WHEEL AND COLUMN
DRIVE AIR BAG (INFLATOR) MODULE
WARNING:
When handling an air bag (inflator) module, be sure to read
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SERVICEº
in Section 10B and observe each instruction. Failure to fol-
low them could cause a damage to the air bag (inflator) mod-
ule or result in personal injury.
REMOVAL
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Loosen 2 bolts mounting driver air bag (inflator) module till it
turns freely, pull them out and fix them to bolt clamps.
4) Remove air bag (inflator) module from steering wheel.
5) Remove driver air bag (inflator) module (yellow) connector and
horn connector from steering wheel.
6) Disconnect driver air bag (inflator) module (yellow) connector of
driver air bag (inflator) module and horn connector as shown in
the figure.
ii) Release locking of lever.
ii) After unlocked, disconnect connector.
WARNING:
Special care is necessary when handling and storing a
live (undeployed) air bag (inflator) module. Observe
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SER-
VICEº in Section 10B. Otherwise, personal injury may re-
sult.
Page 189 of 801
YH4
GRAND
VITARA
6, (a)
1. Trim cover (pad surface)
2. Inflator case
3. Wire harness
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
5. Mounting bolt (left side)
6. Mounting bolt (right side)
AIR BAG STEERING WHEEL AND COLUMN 3C1-5
INSPECTION
WARNING:
Never disassemble air bag (inflator) module or measure its
resistance. Otherwise, personal injury may result.
CAUTION:
If air bag (inflator) module was dropped from a height of
90 cm (3 ft) or more, it should be replaced.
Check air bag (inflator) module visually and if any of the following
is found, replace it with a new one.
Air bag being deployed.
Trim cover (pad surface) being cracked.
Wire harness or connector being damaged.
Air bag (inflator) module being damaged or having been exposed
to strong impact (dropped).
INSTALLATION
1) Connect horn connector securely.
2) Connect yellow connector of driver air bag (inflator) module con-
nector as shown in the figure securely.
ii) Connect connector.
ii) Lock connector with lock lever.
3) Install horn connector and driver air bag (inflator) module con-
nector.
4) Install driver air bag (inflator) module to steering wheel, taking
care so that no part of wire harness is caught between them.
5) Make sure that clearance between module and steering wheel
is uniform all the way.
6) Tighten driver air bag (inflator) module mounting bolt (left side)
to specified torque first and then driver air bag (inflator) module
mounting bolt (right side) to specified torque.
Tightening Torque
(a): 9 N
.m (0.9 kg-m, 6.5 lb-ft)
7) Connect negative battery cable.
8) Enable air bag system. Refer to ªENABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
Page 536 of 801
YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-5
CLEARANCE, TAIL AND LICENCE PLATE LIGHTS
TroublePossible causeCorrection
All lights do not lightªTAILº fuse blown
Lighting switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Some lights do not light
upBulb(s) blown
Wiring or grounding faultyReplace bulb(s)
Repair
BACK-UP LIGHTS
TroublePossible causeCorrection
Back-up lights do not
lightªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)
Bulb blown
switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace bulb
Replace switch
Repair
Back-up lights remains
ONBack-up light switch or shift switch faulty
Wiring or grounding faultyReplace switch
Repair
BRAKE LIGHTS
TroublePossible causeCorrection
Brake lights do not light
upªSTOP / HORNº fuse blown (Hard Top
Model)
ªSTPº fuse blown (Canvas Top Model)
Bulb(s) blown
Brake light switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace bulb(s)
Adjust or replace switch
Repair
Brake lights stay onBrake light switch faultyAdjust or replace switch
Only one light does not
lightBulb blown
Wiring or grounding faultyReplace bulb
Repair
REAR FOG LIGHT (IF EQUIPPED)
TroublePossible causeCorrection
Rear fog light does not
come onªFOGº fuse blown
Rear fog light switch faulty
Lighting switch faulty
Wiring or grounding faulty
Bulb blownReplace fuse to check for short
Replace fog light switch
Replace switch
Repair
Replace bulb
INTERIOR LIGHTS
TroublePossible causeCorrection
Interior light (s) does (do)
not light upBulb(s) blown
ªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top Model)
Wiring or grounding faulty
Door switch faulty
Interior light switch faultyReplace bulb(s)
Replace fuse to check for short
Repair
Replace switch
Replace light assy
Front spot lights do not
light upBulb(s) blown
Wiring or grounding faulty
Spot light switch faultyReplace bulb(s)
Repair
Replace light assy