Disc brake SUZUKI GRAND VITARA 2004 2.G Service User Guide

YH4
GRAND
VITARA
1. Brake pipe flare nut
2. Brake pipe
3. Brake back plate
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Nut 1. Wheel speed sensor
2. Wheel speed sensor coupler
3. Wheel speed sensor harness clamp
4. Wheel speed sensor harness
3E-16 REAR SUSPENSION
REAR AXLE HOUSING
REMOVAL
1) Drain differential gear oil.
Carry out steps 2) to 7) and 15) to 18) on both right and left
wheels.
Note that left wheel and its related parts are used in illustrations
in this section.
2) Remove rear brake drum. (Refer to steps 1) to 5) of BRAKE
DRUM REMOVAL.)
3) Disconnect brake pipe from wheel cylinder. With right side wheel
cylinder, disconnect 2 brake pipes.
4) For vehicle with ABS, disconnect wheel speed sensor coupler
and remove wheel speed sensor with its harness.
5) Remove rear wheel bearing retainer nuts from rear axle hous-
ing.
6) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.

YH4
GRAND
VITARA
1. Flexible hose
2. E-ring
3. Brake pipe
4. Cross member1. LSPV stay
1. Hose
2. Axle housing
1. Propeller shaft
2. Differential carrier
REAR SUSPENSION 3E-17
7) Using special tools (B) & (C) indicated below, draw out axle
shafts. For vehicle equipped with ABS, remove wheel speed
sensor from axle housing before drawing out axle shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
Special Tool
(C): 09943-35512
(B): 09942-15510
8) For vehicle without ABS, remove LSPV stay from axle housing.
9) Remove brake back plate from rear axle housing.
10) Disconnect brake pipe from flexible hose and remove E-ring
(front side).
11) Remove brake pipe clamps and pipes from axle housing and
disconnect breather hose from axle housing.
12) Disconnect propeller shaft and remove propeller shaft from
transmission.

YH4
GRAND
VITARA
3F-6 WHEELS AND TIRES
ON-VEHICLE SERVICE
WHEEL
REMOVAL
1) Loosen wheel nuts by approximately 180
(half a rotation).
2) Hoist vehicle.
3) Remove wheel.
NOTE:
Never use heat to loosen tight wheel because application of
heat to wheel can shorten life of wheel and damage wheel
bearings.
INSTALLATION
Wheel nuts must be tightened in sequence and to proper torque to
avoid bending wheel or brake drum or disc as in figure.
NOTE:
Before installing wheels, remove any build-up of corrosion on
wheel mounting surface and brake drum or disc mounting sur-
face by scraping and wire brushing. Installing wheels without
good metal-to-metal contact at mounting surfaces can cause
wheel nuts to loosen, which can later allow wheel to come off
while vehicle is moving.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)

YH4
GRAND
VITARA
5
BRAKES 5-1
GENERAL DESCRIPTION5- 2 . . . . . . . . . . . . . .
DIAGNOSIS5- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Road Testing Brakes 5- 3. . . . . . . . . . . . . . . . . .
Brake Fluid Leaks 5- 3. . . . . . . . . . . . . . . . . . . .
Substandard or Contaminated
Brake Fluid 5- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 5- 4. . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5- 7 . . . . . . . . . . . .
Bleeding Brakes 5- 7. . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Free Height Check 5- 9. . . . . . . .
Brake Light Switch Adjustment 5- 9. . . . . . . . .
Excessive Pedal Travel Check 5- 9. . . . . . . . .
Brake Pedal Play Check 5-10. . . . . . . . . . . . . . .
Brake Fluid Level Check 5-10. . . . . . . . . . . . . . . Brake Hose and Pipe Check 5-10. . . . . . . . . . .
Master Cylinder Check 5-10. . . . . . . . . . . . . . . .
Brake Disc Check 5-11. . . . . . . . . . . . . . . . . . . .
Brake Pad Check 5-11. . . . . . . . . . . . . . . . . . . . .
Brake Shoe Check 5-11. . . . . . . . . . . . . . . . . . . .
Parking Brake Check and
Adjustment 5-12. . . . . . . . . . . . . . . . . . . . . . . . .
Flushing Brake Hydraulic System 5-13. . . . . . .
Fluid Pressure Test 5-13. . . . . . . . . . . . . . . . . . .
Booster Operation Check 5-15. . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5-17 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL5-17 . . . . . . . .
SPECIAL TOOLS5-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
BRAKES
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

When inspecting and servicing vehicle equipped with ABS, be sure to refer to section 5E or 5E1 first.

All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to as-
sure proper retention of all parts. There is to be no welding as it may result in extensive damage and
weakening of the metal.
DIAGNOSIS5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKE PIPE / HOSE / MASTER CYLINDER5A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT BRAKE5B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING AND REAR BRAKE5C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS

YH4
GRAND
VITARA
[FOR VEHICLE WITHOUT ABS]
[FOR VEHICLE WITH ABS]
1. Master cylinder
2-1. 4-way joint
2-2. 2-way joint
3. LSPV (Load Sensing Proportioning Valve)
4. Rear axle housing
5. ABS actuator (H.U.)
F.R.:Front side
5-2 BRAKES
GENERAL DESCRIPTION
When the foot brake pedal is depressed, hydraulic pressure is developed in the master cylinder to actuate pistons
(two in front and four in rear).
The master cylinder is a tandem master cylinder. Brake pipes are connected to the master cylinder and they make
two independent circuits. One connects front brakes (right and left) and the other connects rear brakes (right and
left).
The load sensing proportioning valve (LSPV) is included in these circuits between the master cylinder and the rear
brake for the vehicle without ABS.
In this brake system, the disc brake type is used for the front wheel brake and a drum brake type (leading / trailing
shoes) for the rear brake.
The parking brake system is mechanical. It applies brake force to only rear wheels by means of the cable and me-
chanical linkage system. The same brake shoes are used for both parking and foot brakes.

YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing force
Brake oil leakage from brake lines.

Brake disc or pads stained with oil.

Overheated brakes.

Poor contact of shoes on brake drum.

Brake shoes linings stained with oil or wet
with water.

Badly worn brake shoe linings.

Defective wheel cylinders.

Malfunctioning caliper assembly.

Air in system.

Maladjusted sensor spring length of LSPV.

Broken sensor spring of LSPV.

Defective collar of LSPV.

Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)
Pad or shoe linings are wet with water or
stained with oil in some brakes.

Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)

Drum is out of round in some brakes.

Wheel tires are inflated unequally.

Malfunctioning wheel cylinders.

Disturbed front end alignment.

Unmatched tires on same axle.

Restricted brake pipes or hoses.

Malfunctioning caliper assembly.

Loose suspension parts.

Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)
Front lining worn out.Replace linings.
Rear brake locked
prematurely
Maladjusted sensor spring length of LSPV.

Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)
Malfunctioning ABS, if equipped.Check system and replace as
necessary.

YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)
Partial brake system failure.

Insufficient fluid in master cylinder
reservoirs.

Air in system. (pedal soft / spongy)

Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)

Bent brake shoes.

Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)
Master cylinder pistons not returning
correctly.

Restricted brake pipes or hoses.

Incorrect parking brake adjustment on rear
brakes.

Weakened or broken return springs in the
brake.

Sluggish parking-brake cables or linkage.

Wheel cylinder or caliper piston sticking.

Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)
Damaged or loose wheel bearings.

Distorted steering knuckle or rear axle
shafts.

Excessive disc lateral runout.

Parallelism not within specifications.

Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noise
Glazed shoe linings, or foreign matters
stuck to linings.

Worn or distorted shoe linings.

Loose front wheel bearings.

Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.

YH4
GRAND
VITARA
1. 4-way joint / 2-way joint
2. Master cylinder
3. LSPV
4. Right brake caliper
5. Left brake caliper
6. Right wheel cylinder
7. Left wheel cylinder
8. ABS actuator

: Air bleeding point [A]: Without ABS
[B]: With ABS
1. Plug cap2. Vinyl tube (See-through tube)
3. Container
[A]
[B]
BRAKES 5-7
CHECK AND ADJUSTMENT
BLEEDING BRAKES
CAUTION:
Brake fluid is extremely damaging to paint. If fluid should
accidentally touch painted surface, immediately wipe
fluid from paint and clean painted surface.
NOTE:
For vehicle equipped with ABS, make sure that ignition switch
turns off.
Be sure to bleed air of brake system according to following proce-
dure when its oil hydraulic circuit has been disconnected.
Hydraulic lines of brake system consists of two separate lines, one
for front wheel brakes and the other for rear wheel brakes.
Air bleeding is necessary at right and left front wheel brakes, left
rear wheel brake and LSPV (if equipped without ABS), i.e. 4 places
(3 places for vehicle with ABS) in all.
1) Fill master cylinder reservoir with brake fluid and keep at least
one-half full of fluid during bleeding operation.
2) Remove bleeder plug cap.
Attach a vinyl tube to bleeder plug of wheel cylinder, and insert
the other end into container.
3) Depress brake pedal several times, and then while holding it de-
pressed, loosen bleeder plug about one-third to one half turn.

YH4
GRAND
VITARA
1. Pad rim
2. Lining
3. Disc
1. Rubber plug
2. Brake shoe
3. Brake shoe rim
BRAKES 5-11
BRAKE DISC CHECK
Refer to FRONT DISC BRAKE PAD of Section 5B for inspection
point and procedure.
BRAKE PAD CHECK
Inspect pad linings periodically according to maintenance schedule
whenever wheels are removed (for tire rotation or other reason).
Take a look through hole of caliper and check lining thickness of in-
side pad.
Thickness ªeº
Standard: 10.0 mm (0.39 in.)
Service Limit: 2.0 mm (0.08 in.)
If one of brake pad is worn to service limit, all linings must be re-
placed at the same time.
BRAKE SHOE CHECK
Inspection should be carried out on following points after brake ped-
al travel ªcº (pedal to asphalt sheet clearance) check as described
on previous page of this section, even when it is more than 115 mm
(4.53 in.).
Amount of brake shoe wear can be checked as follows.
1) Hoist vehicle.
2) Remove rubber plug from brake back plate.
3) Through hole of back plate, visually check for thickness of brake
shoe lining. If lining thickness ªfº is found less than below speci-
fied wear limit, replace with new brake shoes.
Thickness ªfº
Service Limit: 1.0 mm (0.04 in.)

YH4
GRAND
VITARA
3. LSPV stay
1. Master cylinder
2. Disconnect brake pipe1. LSPV lever
2. LSPV spring
3, ªAº 2
1
2(a)
ªaº
ªbº
5-14 BRAKES
3) Depress brake pedal gradually till fluid pressure of front brake
becomes as specified below and check corresponding pressure
of rear brake then. It should be within specification given below.
Front brake
Rear brake
8,000 kPa
80 kg / cm2
3 Door
6,000 ± 7,300 kPa
60 ± 73 kg / cm2
853 ± 1,038 psi80 kg / cm2
1,138 psi5 Door
4,500 ± 7,300 kPa
45 ± 73 kg / cm2
640 ± 1,038 psi
As done above, apply 100 kg / cm2 pressure to front brake and
check that rear brake pressure then is within specification as giv-
en below.
Front brake
Rear brake
10,000 kPa
100 kg / cm2
3 Door
6,500 ± 8,000 kPa
65 ± 80 kg / cm2
924 ± 1,138 psi100 kg / cm2
1,422 psi5 Door
5,000 ± 8,000 kPa
50 ± 80 kg / cm2
711 ± 1,138 psi
4) If rear brake pressure is not within specification, adjust it by
changing stay ªAº position as follows.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

If rear brake pressure is higher than specification, move stay
ªAº to direction ªaº and if it is lower, to direction ªbº.

Repeat steps 3) and 4) until rear brake pressure is within spec-
ification.

After adjustment, be sure to torque bolt to specification.
5) Disconnect brake pipe (connecting between master cylinder
secondary side and 4-way joint) from master cylinder.
Tighten plug (special tool) to master cylinder.
Depress brake pedal. If rear brake pressure is 95 ± 100 kg / cm
2
when front brake pressure is 100 kg / cm2, it means that front fail-
safe system functions properly.
Front brake
Rear brake
10000 kPa
100 kg / cm2
1422 psi
9500 ± 10000 kPa
95 ± 100 kg / cm2
1350 ± 1422 psi
Special Tool
(A): 09956-02210