parts SUZUKI GRAND VITARA 2004 2.G Service Owner's Guide

YH4
GRAND
VITARA
3C
STEERING WHEEL AND COLUMN 3C-1
SECTION 3C
STEERING WHEEL AND COLUMN
(NOT EQUIPPED WITH AIR BAG)
NOTE:
All steering wheel and column fasteners are important parts in that they could affect the performance of
vital parts and systems, and / or could result in major repair expense. They must be replaced with one of
the same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality of substitute design. Torque values must be used as specified during reassemb-
ly to assure proper retention of this part.
CONTENTS
GENERAL DESCRIPTION3C- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS3C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and repair required after accident 3C- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Combination switch3C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering column assembly3C- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lock assembly (ignition switch) 3C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lower shaft assembly3C-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking steering column for accident damage 3C-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable steering column release lever 3C-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified bolts be used as designated and that
they are tightened to the specified torque. When the column assembly is removed from the vehicle, special care
must be taken in handling it. Use of a steering wheel puller other than the one recommended in this manual or a
sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly could shear the
plastic shear pins which maintain column length and position.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
: If equipped
*
3C-6 STEERING WHEEL AND COLUMN
2) Remove steering wheel and combination switch, if necessary.
Refer to ªSTEERING WHEELº and ªCOMBINATION SWITCHº
in this section.
Perform the following procedure if not removing steering wheel
and / or combination switch.
i) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
3) Remove steering column hole cover.
4) Disconnect all connectors for the following parts.

Combination switch

Ignition switch

Immobilizer control system parts (if equipped)
5) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
6) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C-14 STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at higher position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
SPECIAL TOOL

YH4
GRAND
VITARA
3C1
AIR BAG STEERING WHEEL AND COLUMN 3C1-1
GENERAL DESCRIPTION3C1- 2 . . . . . . . . . . . . .
DIAGNOSIS3C1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair Required after
Accident 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C1- 3 . . . . . . . . . . . . . . .
Service Precautions 3C1- 3. . . . . . . . . . . . . . . . .
Diagnosis and Servicing 3C1- 3. . . . . . . . . . . .
Disabling Air Bag System 3C1- 3. . . . . . . . . . .
Enabling Air Bag System 3C1- 3. . . . . . . . . . .
Handling and Storage 3C1- 3. . . . . . . . . . . . . .
Disposal 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Air Bag (Inflator) Module 3C1- 4. . . . . . . .
Steering Wheel 3C1- 6. . . . . . . . . . . . . . . . . . . . . . Centering Contact Coil 3C1- 6. . . . . . . . . . . . .
Contact Coil and Combination Switch
Assembly 3C1- 7. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Column 3C1- 9. . . . . . . . . . . . . . . . . . . .
Steering Lock Assembly (Ignition
Switch) 3C1-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Lower Shaft Assembly 3C1-15. . . . . . .
Checking Steering Column for Accident
Damage 3C1-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Steering Column Release
Lever 3C1-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3C1-18 . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C1-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3C1
AIR BAG STEERING WHEEL AND COLUMN
WARNING:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in air bag system section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintentional activation of the system
or could render the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
1
3C1-10 AIR BAG STEERING WHEEL AND COLUMN
REMOVAL
WARNING:
Never rest a steering column assembly on the steering
wheel with air bag (inflator) module face down and column
vertical. Otherwise personal injury may result.
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Remove steering wheel and contact coil and combination switch
assembly, if necessary. Refer to ªSTEERING WHEELº and
ªCONTACT COIL AND COMBINATION SWITCH ASSEMBLYº
in this section.
Perform the following procedure if not removing steering wheel
and/or combination switch.
ii) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
4) Remove steering column hole cover.
5) Disconnect all connectors for the following parts.

Contact coil and combination switch

Ignition switch
6) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
7) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C1-18 AIR BAG STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at upper position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Driver air bag (inflator) module bolt90.96.5
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
Shift (key) interlock cable screw2.20.221.6
SPECIAL TOOL

YH4
GRAND
VITARA
3D
FRONT SUSPENSION 3D-1
GENERAL DESCRIPTION3D- 2 . . . . . . . . . . . . . .
DIAGNOSIS3D- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3D- 3. . . . . . . . . . . . . . . . . . . . . .
Stabilizer Bar and Bushing Check 3D- 3. . . . . .
Strut Damper and / or Coil Spring Check 3D- 3. .
Suspension Arm / Knuckle Check 3D- 3. . . . . . . .
Suspension Control Arm Joint Check 3D- 4. . . .
Suspension Control Arm Bushing Check 3D- 4.
Wheel Disc, Nut & Bearing Check 3D- 4. . . . . .
ON-VEHICLE SERVICE3D- 5 . . . . . . . . . . . . . . . . Stabilizer Bar / Bushings 3D- 5. . . . . . . . . . . . . . .
Strut Damper 3D- 6. . . . . . . . . . . . . . . . . . . . . . . .
Coil Spring 3D- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Stopper / Spring Rubber Seat 3D-11. . . . .
Wheel Hub (Included Wheel Bearing) 3D-12. . .
Knuckle / Wheel Spindle 3D-17. . . . . . . . . . . . . . . .
Suspension Control Arm / Bushings 3D-21. . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3D-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3D-24 . . . . . .
SPECIAL TOOLS3D-25 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3D
FRONT SUSPENSION
CAUTION:

All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and / or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
CONTENTS

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to Section 3.
STABILIZER BAR AND BUSHING CHECK
BAR
Inspect for damage or deformation. If defective, replace.
BUSHING
Inspect for damage, wear or deterioration. If defective, replace.
STRUT DAMPER AND / OR COIL SPRING
CHECK
1) Inspect strut for oil leakage. If strut is found faulty, replace it as
an assembly unit, because it can not be disassembled.
2) Strut function check
Check and adjust tire pressures as specified.
Bounce body three or four times continuously by pushing front
end on the side with strut to be checked. Apply the same amount
of force at each push and note strut resistance both when
pushed and rebounding.
Also, note how many times vehicle body rebounds before com-
ing to stop after hands are off. Do the same for strut on the other
side.
Compare strut resistance and number of rebound on the right
with those on the left.
And they must be equal in both. With proper strut, body should
come to stop the moment hands are off or after only one or two
small rebounds. If struts are suspected, compare them with
known good vehicle or strut.
3) Inspect for damage or deformation.
4) Inspect strut boot for damage or crack.
5) Inspect for cracks or deformation in spring seat.
6) Inspect for deterioration of bump stopper.
7) Inspect strut mount for wear, cracks or deformation.
Replace any parts found defective in steps 2) ± 7).
SUSPENSION ARM / KNUCKLE CHECK
Inspect for cracks, deformation or damage.

YH4
GRAND
VITARA
3D-4 FRONT SUSPENSION
SUSPENSION CONTROL ARM JOINT CHECK
1) Check for smoothness of rotation.
2) Inspect ball stud for damage.
3) Inspect dust cover for damage.
Replace any parts found defective in steps 1) ± 3).
SUSPENSION CONTROL ARM BUSHING
CHECK
Inspect for damage, wear or deterioration.
WHEEL DISC, NUT & BEARING CHECK
1) Inspect each wheel disc for dents, distortion and cracks.
Disc in badly damaged condition must be replaced.
2) Check wheel nuts for tightness and retighten them to specifica-
tion as necessary.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
3) Check wheel bearing for wear. After retightening lock nut to spe-
cified torque, apply dial gauge to wheel hub center and measure
thrust play.
Thrust play limit: 0.05 mm (0.002 in.)
When measurement exceeds limit, replace bearing.
4) By rotating wheel actually, check wheel bearing for noise and
smooth rotation. If defective, replace bearing.

YH4
GRAND
VITARA
3E
REAR SUSPENSION 3E-1
GENERAL DESCRIPTION3E- 2 . . . . . . . . . . . . . .
DIAGNOSIS3E- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3E- 3. . . . . . . . . . . . . . . . . . . . . .
Shock Absorber Check 3E- 3. . . . . . . . . . . . . . . .
Lower / Upper / Lateral Rod Check 3E- 3. . . . . . . .
Axle Housing and Coil Spring Check 3E- 3. . . .
Bearing Retainer & Axle Shaft Inner Oil
Seal Check 3E- 4. . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Disc, Nut & Bearing Check 3E- 4. . . . . .
ON-VEHICLE SERVICE3E- 5 . . . . . . . . . . . . . . . .
Shock Absorber 3E- 5. . . . . . . . . . . . . . . . . . . . . . Coil Spring 3E- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Rod 3E- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Rod 3E- 9. . . . . . . . . . . . . . . . . . . . . . . . . .
Lateral Rod 3E-10. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Axle Shaft and Wheel Bearing 3E-10. . . . .
Rear Axle Shaft Inner Oil Seal 3E-15. . . . . . . . . .
Rear Axle Housing 3E-16. . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3E-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3E-23 . . . . . .
SPECIAL TOOLS3E-24 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3E
REAR SUSPENSION
NOTE:

All suspension fasteners are an important attaching part in that it could affect the performance of vital
parts and systems, and / or could result in major repair expense. They must be replaced with one of the
same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality or substitute design. Torque values must be used as specified during reas-
sembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any suspension part. Replace it with a new part, or damage
to the part may result.
CONTENTS