lock SUZUKI GRAND VITARA 2008 3.G Inspection And Maintenance Manual

Downloaded from www.Manualslib.com manuals search engine Open the engine hood. Disconnect the Front Fog Light coupler. Remove the sealing rubber.
Push the retaining spring forward and
unhook it. Then remove the bulb. Install a
new bulb in the reverse order of removal.
•
Discharge head lamp
Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for bulb replacement.
High beam
78F072
Open the engine hood. Disconnect the coupler while pushing the lock release. Turn the bulb holder counterclockwise to remove it.
II~
~1
79K090
1) Insert a flat blade screw driver into the hole (2) and remove the clips (1) by twist the driver as shown in the illustra-tion. .
2) Remove the bolt (3) by a Phillips-head screw driver. .
INSPECTION AND MAINTENANCE
79K091
3) Remove the clip (4) with the same way as No.1).
7-38

Downloaded from www.Manualslib.com manuals search engine INSPECTION AND MAINTENANCE
78F072
4) Open the fender cover. Disconnect the
coupler with pushing the lock release.
Turn the bulb holder counterclockwise
and remove it.
7-39
Other General Lights
Bulb holder
EXAMPLE 0 "'"
o (2~
~
(2) ,~
(1) ~.
(1) Removal (2) Installation
54G123
To remove a bulb holder from a light hous­
ing, turn the holder counterclockwise and
pull
it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
EXAMPLE~
.. O~y
X?3
-< ~~
~& "~d
(1) • B>~
.(3) r<0' Q(4) V-=-(2)
(3) Removal
(4) Installation
54G124
There are two types of bulb, "Full glass type" (1) and "Glass/metal type" (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.

Downloaded from www.Manualslib.com manuals search engine Parking light Front turn signal light
For 3 door model
64J193
For 5 door model
To replace the bulb of parking/turn signal
light, follow the procedure for the bulb
replacement of the "Front Fog Light".
Rear combination light
78K124
Side turn signal light
64J195
INSPECTION AND MAINTENANCE
As the bulb is built-in type, the light assem­bly must be replaced. Remove the light
assembly by sliding the light housing left­ward with your finger.
License plate light
65J345
Turn the cover (1) counterclockwise to
remove it.
NOTE: When reinstalling, put the packing . (2)
between the cover and bulb holder.
7-40

Downloaded from www.Manualslib.com manuals search engine INSPECTION AND MAINTENANCE
For windshield wipers:
70G119
1) Hold the wiper arm away from the win­dow.
7-43
EXAMPLE
EXAMPLE
54G130
2) Squeeze lock (1) towards wiper arm (2) and remove the wiper frame from the
arm as shown.
3)
Unlock the lock end of the wiper blade and slide the blade out as shown.
Type A (Removal)
60A260
Type A (Installation)
..,
54G132
(1) Locked end

Downloaded from www.Manualslib.com manuals search engine Type B (Removal)
54G133
Type B (Installation)
54G134
(1) Locked end
TypeC
650151
NOTE:
For Type C, do not flex the wiper blade frame end more than necessary If you do, it can break off.
INSPECTION AND MAINTENANCE
(1) Retainer
4) If the new blade is provided without the
two metal retainers, move them from
the old blade to the new one. 5) Install the new blade in the reverse
order of removal, with the locked end
positioned toward the wiper arm
(except
Type C). Make sure the blade is properly
retained by all the hooks. Lock the
blade end into place.
6) Reinstall wiper frame to arm, making
sure that the lock lever is snapped
securely into the arm.
7-44