lock SUZUKI GRAND VITARA 2008 3.G Operating Manual

Downloaded from www.Manualslib.com manuals search engine Transfer Switch Operation
Switching between U4H LOCK" and U4L LOCK"
Switching between U4H" and UN"
Warning and Indicator messages
I 1).'110 .8.CCEL ':'FF 1<>1 OE."-.RSHIFT I·.J
79K080
79K081
79K082
I 1<>1 SV'-iIT':Hlf'.JG
79K083
Master Warn­ing Indicator
Off
Off
Off
Off
Sound
Series of Beeps
Series of Beeps
Beep or
Off
Off
OPERATING YOUR VEHICLE
Cause and Remedy
(For automatic transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal.
Shift the automatic transmission gear­shift lever to the uN" position.
(For
manual transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal and clutch
pedal.
The desired transfer gear has not been
engaged.
Turn the transfer switch back to the pre­
viously selected position, and operate
the transfer switch again.
This message informs
you the 4WD
mode is switching.
Do not move your vehicle.
3-28

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Cruise Control (if equipped)
79K032
The cruise control system allows you to maintain a steady speed without keeping
your foot on the accelerator pedal. The controls for operating the cruise control system are on the steering wheel. You can
use the cruise control system at speeds of
about 40 km/h (25 mph) or higher.
A WARNING
To help avoid loss of vehicle control, do not use the cruise control system
when driving in heavy traffic, on slip­pery or winding roads, or on steep
downgrades.
3-29
NOTE: If the transfer switch (if equipped) is in the "4L LOCK" position, you can not use the
cruise control system. Refer to "Using the
Transfer Switch (if equipped)" in this sec­
tion.
CRUISE
52Dl13
When you push the "ON/OFF" switch, the
system is on and a "CRUISE" indicator light on the instrument cluster will be on.
SET
65D474
When the vehicle's speed is controlled by the cruise control system, a "SET' indica­
tor light on the instrument cluster will be on.
(2) ----\-l~
(4) (1)
79K049
To Set Cruising Speed Turn on the cruise control system by push­
ing the "ON/OFF" switch (1). Accelerate to the desired speed and push the "SET/
COAST' switch (3). Take your foot off the accelerator pedal and the set speed will be maintained.
With the cruise
control on, you can increase speed for passing by using the accelerator pedal. When you take your foot
off the pedal, your vehicle will return to the
set speed.
To Change Cruising Speed To reset the cruise control to a slower speed, hold in the "SET/COAST' switch (3) until the vehicle has slowed to the desired
speed, then release the switch. The new
speed will be maintained.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
If
water gets into the brake drums,
brake performance may become poor
and unpredictable.
After driving through water or wash­
ing the underside of the vehicle, test
the brakes while driving at a slow speed to see if they have maintained
their normal effectiveness. If the
brakes are less effective than normal, dry them by repeatedly applying the
brakes while driving slowly until the
brakes have regained their normal effectiveness.
Power Assisted Brakes Your vehicle has power assisted brakes. If power assistance is lost due to a stalled engine or other failures, the system is still
fully operational on reserve power and you can bring the vehicle to a complete stop by pressing the brake pedal once and holding it down. The reserve power is partly used
up when you depress the brake pedal and reduces each time the pedal is pressed. Apply smooth and even pressure to the pedal. Do not pump the pedal.
3-31
A WARNING
Even without reserve power in the
brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. How­ever, the stopping distance may be longer.
Brake Assist System When you slam the brakes on, the brake
assist system judges as an emergency
stop and provides more powerful braking
for a driver who cannot hold down the
brake pedal firmly.
NOTE: If you quickly and forcefully depress the
brakes, you may hear a clicking sound in
the brake pedal. This is normal and indi­
cates that the brake assist system is acti­
vated properly.
Anti-Lock Brake System (ABS) ASS will help you avoid skidding by elec­
tronically controlling braking pressure. It
will also help you maintain steering control when braking on slippery surfaces or when
braking hard.
The
ASS works automatically, so you do
not need any special braking technique.
Just push the brake pedal down without
pumping. The ASS will operate whenever it
senses that the wheels are locking up. You may feel the brake pedal pulsate while the ASS is operating.
NOTE: The ABS will not work if vehicle speed is under about 5 - 6 kmlh (3 - 4 mph).
A WARNING
•
On some types of loose surfaces
(such as gravel, snow-covered
roads, etc.) the stopping distance
required for
an ABS-equipped vehi­cle may be slightly greater than for
a comparable vehicle with a con­ventional brake system. With a conventional brake system, skid­
ding tires are able to "plow" the gravel or snow layer, shortening
the stopping distance, ABS mini­
mizes this resistance effect. Allow for extra stopping distance when driving on loose surfaces. • On regular paved roads, some driv­
ers may be able to obtain slightly shorter stopping distances with
conventional brake systems than
with
ABS. • In both of the above conditions, ABS wi II still offer the advantage of helping you maintain directional control. However, remember that ABS will not compensate for bad road or weather conditions or poor
driver judgment. Use good judg­
ment and do not drive faster than
conditions will
safely allow.

Downloaded from www.Manualslib.com manuals search engine (8) or ABS
(1) (2)
(CD)
BRAKE (3)
(1) ABS warning light Type 1 (2) ABS warning light Type 2 (3) Brake system warning light
A WARNING
65D451
If the ABS warning light «1) or (2» on
the instrument panel comes on and
stays on while driving, there may be a
problem with the ABS system. If this happens:
1) Pull off the road and stop care­
fully.
2) Turn the ignition switch to "LOCK" and then start the engine again.
(Continued)
A WARNING
(Continued) If the warning light comes on briefly then turns off, the system is normal.
If the. warning light still stays on,
have the system inspected by your
SUZUKI dealer immediately.
If the ABS system becomes inopera­tive, the brake system will function as
an ordinary brake system that has no
ABS.
A WARNING
If the ABS warning light «1) or (2» and the Brake system warning light (3) on the instrument panel simulta­
neously stays on or comes on when
driving, both anti-lock function and
rear brake force control function (pro­portioning valve function) of the ABS system may have failed. If so, the rear wheels may easily skid or the vehicle can even spin in the worst case when
braking on a slippery road or when
hard braking even on a dry paved
road. Ask your SUZUKI dealer to inspect the ABS system immediately. Drive carefully, avoiding hard braking
as much as possible.
OPERATING YOUR VEHICLE
How the ABS Works A computer continuously monitors wheel speed. The' computer compares the
changes in wheel speed when braking. If the wheels slow suddenly, indicating a
skidding Situation, the computer will change braking pressure several times
each second to prevent the wheels from locking. When you start your vehicle or when you accelerate after a hard stop, you may hear a momentary motor or clicking sound as the system resets or checks itself.
A WARNING
The ABS may not work properly if
tires or wheels other than those
specified in the owner's manual are
used. This is because the ABS works
by comparing changes in wheel speed. When replacing tires or wheels, use only the size and type
specified in this owner's manual.
3-32

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Electronic Stability Program
(ESP~ (if equipped)
ESP® is a registered trademark of Daimler AG.
The Electronic Stability Program (ESP~ helps to control the vehicle during corner­
ing if front wheels or rear wheels skid. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the
engine's output, and by selectively apply­ing the brakes. In addition, ESP® helps to
avoid skidding by controlling braking pres­
sure.
A WARNING
The ESP® cannot enhance the vehi­
cle's driving stability in all situations and does not control your vehicle's entire braking system. The ESP® can­not prevent accidents, including those resulting from excessive speed
in turns, or hydroplaning. Only a safe
and attentive driver can prevent acci­dents. The capabilities of an ESP®­equipped vehicle must never be used
as a substitute for careful driving.
3-33
The ESP® has the following three systems:
Stability Control System The vehicle stability control system helps provide integrated control of systems such as anti-lock brakes, traction control, engine control, etc. This system automatically
controls the brakes and engine to help pre­
vent the vehicle from skidding when cor­
nering on a slippery road surface or when
turning the steering wheel abruptly.
Traction Control System The traction control system automatically
helps prevent the spinning of wheels when
the vehicle is started or accelerated on slippery road surfaces. The system oper­
ates only if it senses that some of the wheels are spinning or beginning to lose traction. When this happens, the system
operates the front or rear brakes and
reduces engine power to
limit wheel spin.
NOTE: You may hear a clicking sound in the
engine compartment for a few seconds when you start the engine or just after the
vehicle begins to move. This means that
the above systems are in the self-check mode. This sound does not indicate a mal­
function.
Anti-Lock Braking System (ABS) ABS will help you avoid skidding by elec­
tronically controlling braking pressure. It will also help you maintain steering control when braking on slippery surfaces or when
braking hard. The ABS works automati­cally, so you do not have to use any special braking technique. Just push the brake pedal down without pumping. The ABS will operate whenever it senses that wheels are locking up. You may feel the brake pedal pulsate while the ABS is operating.
(For more information on ABS, see "Brak­
ing" in the "OPERATING YOUR VEHICLE" section.)
NOTE: If the ABS system is activated, you may
hear a clunking noise and/or feel pulsating in the brake pedal. This is normal and indi­
cates that the brake fluid pressure is being
controffed properly

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
"ESP" Warning Light
ESP
66J031
When the ESP® systems (other than ABS) have a system malfunction, the "ESP" warning light in the instrument cluster comes on.
CAUTION
If the "ESP" warning light comes on,
or stays on while driving, there may
be a malfunction of the ESP® sys­tems (other than ABS). You should
have the systems inspected by an authorized SUZUKI dealer.
NOTE: When the "ESP" warning light comes on, or stays on while driving, indicating a mal­function of the ESp!Y systems (other than ABS), the brake system will function as an
ordinary ABS that has no additional ESp!Y functions.
NOTE: The information display shows the warning and indicator message when this light
comes on.
3-35
"ESP OFF" Indicator Light
ESP
OFF
66J032
You should turn the ESP® on during your
ordinary driving, so that you have the ben­efits of all of the ESP® systems.
It may be required to turn the ESP® sys­tems (other than ABS) off if your vehicle is stuck in sand, mud, or snow, or when driv­ing in extreme off-road conditions where wheel spin is necessary.
"ESP OFF" switch
(without hill descent control)
(1)
78K045
(with hill descent control)
'"'---+-( 1 )
78K046
(1) "ESP OFF" switch
When the
"ESP OFF" switch located at the
center of the instrument panel is pushed
and held
to turn off the ESP® systems
(other than ABS), the "ESP OFF" indicator
light in the instrument cluster comes on. When you push and hold the "ESP OFF" switch again, the "ESP OFF" indicator light will go out and all of the ESP® systems will be activated.
NOTE: • When the vehicle speed is greater than
approximately 30 kmlh (19 mph), the ESp!Y systems (other than ABS) will turn on automatically and the "ESP OFP' indicator light will go out. • When the transfer switch (if equipped) is turned to the "4L LOCK" position, the

Downloaded from www.Manualslib.com manuals search engine ES~ systems (other than ABS) will be
canceled to provide improved vehicle
traction, and the
~'ESP OFF" indicator
light will come on. When the transfer switch (if equipped) is
turned to the "4L LOCK" position, brake­
traction control can be activated. Brake­
traction control brakes the spinning
wheel to distribute drive power to the other wheels for increased climbing abil­
ity or for better performance on a rolling
hill or a slipe,ery surface .. • If the ESpE> systems operate continu­ously, such as when driving on slippery roads, the traction control functions of the ES~ systems may be canceled
temporarily to avoid overheating the brake pads, and the "ESP OFF" indicator
light will come on. After a short period of time, the ES~ systems (other than ABS) will turn on automatically and the "ESP OFF" indicator light will go out. • If your vehicle is equipped with a hill
descent control system and a hill hold
control system, these systems will not be
turned off
when the "ESP OFF" switch is pushed to turn off the ES~ systems.
E'::.F' OFF I-Qf - -a.'ND S\l',/IT'_ H V"/I)R~;',. I-6-t ONL ',' IN 4HL
79K084
NOTE: If, you push the "ESP OFF" switch when the transfer switch is in the "4H" position, the ES~ systems will not be turned off, and the message shown in the above illus­
tration will appear on the information dis­play. You should turn the transfer switch to the "4H LOCK" position to turn off the ES~ systems. Refer to "Using the Transfer Switch" in this section.
ABS Warning Light I Brake System
Warning Light
See 'Braking" in the "OPERATING YOUR VEHICLE" section.
OPERATING YOUR VEHICLE
Hill descent control System
(if equipped)
The hill descent control system is designed
to reduce the driver's workload when going
down steep, rough and/or slippery hills where the vehicle cannot decelerate enough by engine braking alone. The hill descent control system helps to control
vehicle speed by automatically engaging
the vehicle's brakes, as needed, so you can concentrate on steering the vehicle.
A WARNING
Do not rely excessively on the hill
descent control system. The hill
descent control system may not con­trol vehicle speed on a hill under all load or road conditions. Always be prepared to control vehicle speed by applying the brakes. Failure to pay
attention and control vehicle speed
using the brakes when necessary
may
result in loss' of control or an accident.
3-36

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
H ill descent control switch
ff--+-(1)
79K051
(1) Hill descent control switch
To activate the hill descent control system: 1) Turn the transfer switch to the "4H LOCK" or "4L LOCK" position. 2) Shift the gearshift lever into a forward
gear or reverse gear.
3) Push the hill descent control switch (1) when the vehicle speed is under 25 km/
h (15 mph). The hill descent control
indicator on the instrument cluster will come on and the hill descent control
system will be activated.
If the transfer switch is in the "4H LOCK" position, vehicle speed is maintained at
approximately 1 0 km/h (6 mph) when
going down a hill. If the transfer switch is in the "4L LOCK" position, the vehicle speed is maintained at
3-37
approximately 5 km/h (3 mph) when going
down a hill. The brake/tail lights come on and the slip
indicator light blinks while the hill descent
control system applies the brakes to main­tain the vehicle speed. If the accelerator or brake pedal is
depressed while the hill descent control
system is activated, the system will stop
working temporarily. As soon as the
accel­erator or brake pedal is released, the hill descent control system begins to function
again if the hill descent control operating
conditions are fulfilled. However, when the
vehicle speed exceeds 25 km/h (15 mph),
the
hill descent control system will be deactivated automatically.
To deactivate the hill descent control sys­tem, push the hill descent control switch
again.
CAUTION
When the hill descent control system
is used continuously for a long time,
the temperature of the brake system
may increase and the hill descent
control system may be disabled
tem­porarily. The hill descent control indi­cator blinks to let you know the
system is disabled. Depress the
brake pedal and stop the vehicle
in a
safe place. When the temperature of
the brake system goes down, the hill
descent control indicator will come
on and the system is activated again.
NOTE: You may hear a sound coming from the engine when the hill descent control sys­tem is activated. This sound is normal and
does not indicate a malfunction.
Hill descent control Indicator Light
79K050
When the hill descent control system is
activated, the hill descent control indicator
comes on.
NOTE: If any of the following conditions occur when the hill descent control system is
activated, the hill descent control indicator
blinks.
• The transfer switch is in the "4H" or "N" position • The gearshift lever is in the "P" position • The gearshift lever is moved to the "N" position while driving • The vehicle speed exceeds 25 kmlh (15
mph)