brake light SUZUKI GRAND VITARA 2008 3.G Operating Manual

Downloaded from www.Manualslib.com manuals search engine Daily Inspection Checklist
Before Driving
60A187S
1) Make sure that windows, mirrors, lights, and reflectors are clean and unob­
structed.
2) Visually check the tires for the following points:
- the depth of the tread groove
-
abnormal wear, cracks and damage
-loose wheel nuts
- existence of foreign material such as nails, stones, etc.
Refer to "Tires" in "INSPECTION AND MAINTENANCE" section for details. 3) Look for fluid and oil leaks.
NOTE:
It is normal for water to drip from the air conditioning system after use.
4) Make sure the hood is fully closed and latched. 5) Check the headlights, turn signal lights, brake lights and horn for proper opera­
tion.
6) Adjust the seat and adjustable head
restraint (if equipped).
7) Check the brake pedal and the parking
brake lever. 8) Adjust the mirrors. 9) Make sure that you and all passengers
have properly fastened your seat belts.
10)Make sure that all warning lights come on as the key is turned to the "ON" posi­
tion.
11 )Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once
a week, or each time you fill your fuel tank, perform the following under-hood
checks:
1) Engine oil level 2) Coolant level 3) Brake fluid level 4) Power steering (if equipped) fluid level 5) Windshield washer fluid level 6) Battery solution level 7) Hood latch operation Pull the hood release handle inside the vehicle. Make sure that you cannot
open the hood all the way without releasing the secondary latch. Be sure
to close the hood securely after check-
OPERATING YOUR VEHICLE
ing for proper latch operation. See the
item "All Latches, Hinges & Locks" of "CHASSIS AND BODY" in the "Periodic Maintenance Schedule" in the "INSPECTION AND MAINTENANCE" section for lubrication schedule.
A WARNING
Make sure the hood is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving,
obstructing your view and
resulting in an accident.
Once a month, or each time you fill your fuel tank, check the tire pressure using a
tire pressure gauge. Also check the tire
pressure of the spare tire.
3-2

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A. WARNING
(Continued) • Always return the ignition switch to the "LOCK" position and remove
the ignition key and the remote controller (if equipped) when leav­ing the vehicle even if a short time. Also do not leave children or pets alone in a parked vehicle. Unat­
tended children could cause acci­dental movement of the vehicle or could tamper with power windows or power sunroof. They also could suffer from heat stroke in warm or hot weather. These could result in
severe injury or even death.
CAUTION
• Do not use the starter motor for more than 15 seconds at a time.
For diesel engine model, do not use the starter motor for more than 30 seconds at a time. If the engine
does not start, wait 15 seconds
before trying again. If the engine
does not start after several attempts, check the fuel and igni­tion systems or consult your SUZUKI dealer.
• Do not leave the ignition switch in
the "ON" position if the engine is not running as the battery will dis­charge.
3-7
Parking Brake Lever
EXAMPLE
(1) To set (2) To release (3) To release
64J081
The parking brake lever is located between the seats. To set the parking brake, hold the brake pedal down and pull the parking
brake lever all the way up. To release the parking brake, hold the brake pedal down, pull up slightly on the parking brake lever, push the button on the end of the lever with
your thumb, and lower the lever to its origi­nal position. For
automatic transmission
vehicles,
always set the parking brake before mov­ing the gearshift lever to the "P" (PARK) position. If you park on an incline and shift
into "P" before setting the parking brake, the weight of the vehicle may make it diffi­cult to shift out of "P" when you are ready to drive the vehicle.
When preparing to drive the vehicle, move the gearshift lever out of the "P" position
before releasing the parking brake.
A. WARNING
• Never drive your vehicle with the
parking brake on: rear brake effec­
tiveness can be reduced from over­
heating, brake life may be
shortened,
or permanent brake
damage may result.
• If
the parking brake does not hold the vehicle securely or does not fully release, have your vehicle inspected immediately by an autho­
rized SUZUKI dealer.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Diesel Particulate Filter (DP~ ;::D.:..p.:..j=®----=:w:..::a::..:rn..:.:i:..::ng~lig~h:..:..:t~ _____ _____, The DPj=® filters off the soot 'particles in the exhaust gas, so the DPp!9 could get clogged depending on the driving condi­tion. The DPPW is cleaned by the regener­ating function that combusts the soot
particles in the DPPW by raising the
exhaust gas temperature during driving.
A WARNING
Keep away from the exhaust pipe
when the engine is running. If the DPj=® is regenerating, the exhaust
gas temperature could be higher.
NOTE: When you drive your vehicle, white smoke
may be emitted depending on the grade of fuel used. This is due to the particle filter
regenerating automatically, and does not
affect the way the vehicle runs.
3-11
64J244
If the DPpID warning light comes on when
driving, the DPpID is nearly clogged. You should regenerate the DPpID when the DPPW warniqg light comes on. To regener­ate the DPp!9, you must drive the vehicle
until the light goes out, at a speed of 75 km/h (47 mph) or higher for a while (max. 30 minutes).
However, you should drive carefully and
within the legal speed limit, and should
take in to consideration the surrounding
traffic condition. If you drive your vehicle
until the light goes out, the regeneration of
the DPPW will be completed.
CAUTION
Be sure to regenerate the DPj=® when
the DPj=® warning light comes on.
Failure to regenerate the DPj=® will cause a vehicle malfunction due to the clogged filter.
Using the Transmission
Manual Transmission
Starting off
650449
To start off, depress the clutch pedal all the
way to the floor and shift into 1 st gear. After releasing the parking brake, gradually release the clutch. When you hear a
change in the engine's sound, slowly press
the accelerator while continuing to gradu­
ally release the clutch.
Shifting All forward gears are synchronized, which
provides for quiet, and easy shifting.
Always push
in the clutch pedal fully before
shifting gears.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
• Reduce your speed and downshift to a lower gear before going down
a long or steep hill. A lower gear
will allow the engine to provide
braking. Avoid riding the brakes or they may overheat, resulting in
brake failure.
• When driving on slippery roads, be
sure to slow down before down­shifting. Excessive and or sudden
changes in engine speed may
cause
loss of traction, which could cause you to lose control.
• Make sure that the vehicle is com­
pletely stationary before you shift into reverse.
CAUTION
• To help avoid clutch damage, do not use the clutch pedal as a foot­rest while driving or use the clutch to keep the vehicle stationary on a
hill. Depress the clutch fully when
shifting.
• When shifting or starting off, do not race the engine. Racing the engine
can shorten engine life and affect
smooth shifting.
3-13
5-Speed Automatic Transmission
EXAMPLE
(1) Power mode selector switch
D:
66J055
5-speed automatic transmission mode 4: 4-speed automatic transmission mode
The 4-speed mode is suitable for the fol­
lowing driving conditions: • Driving on hilly, winding roads
-You can drive more smoothly with less frequent gearshifting
• Going down a steep hill -Some engine braking is provided
NOTE:
With the transfer switch in the "4L LOCK" position, the 5-speed automatic transmis­sion will remain in the 4-speed mode.
Power mode selector switch
A/T
POWER
650448
When you need more power for climbing
hills or smooth starting on slippery road,
push the "AfT POWER" switch. To activate
the power mode selector, push the "AfT POWER" switch, and the "POWER" indica­tor light in the instrument cluster comes on. To deactivate, push the switch again, and
the "POWER" indicator light goes off.
Power driving mode When the "AfT POWER" switch is on with
shift in "0" (Drive), "4" (Low 3) or "3" (Low 2) position, if you depress the accelerator
pedal, the shifting points are delayed so
the engine can rev higher in each gear.
Therefore, you can drive more powerfully than normal driving.

Downloaded from www.Manualslib.com manuals search engine Gearshift lever
EXAMPLE
66J056
The gearshift lever is designed that it can not be shifted out of the "P" position unless the ignition switch is in the "ON" position
and the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving unexpectedly when you shift.
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use. the
other gearshift lever positions as described below:
P (Park) Use this position to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle, never leave the transfer switch in uN" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park.
R (Reverse)
Use this position to reverse the vehicle
from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral) Use this position for starting the engine if
the engine stalls and you need to restart it while the vehicle is moving. You may also shift into Neutral and depress the brake pedal to hold the vehicle stationary during idling.
OPERATING YOUR VEHICLE
D (Drive) Use this position for all normal driving.
With the gearshift
lever in "0" range you can get an automatic downshift by press­ing the accelerator pedal. The higher the vehicle speed is, the more you need to press the accelerator pedal to get a down­shift.
4 (Low 3) . Use this position for driving on moderate uphill and downhill gradients. The engine
braking effect on moderate downhills can be used in this position. The transmission
shifts up only to 4th gear.
3 (Low 2) Use this position to provide extra power
when climbing hills, or to provide engine
braking when going down hills.
NOTE: In these 4 or 3 positions, if the power mode
selector switch is turned to the "ON" posi­tion, the transmission will not downshift
into "I.!' (Low 1).
L (Low 1) Use this position to provide maximum
power when climbing steep hills or driving
through deep snow or mud, or to provide
maximum engine braking when going
down steep
hills.
3-14

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
NOTE: 4-Speed Automatic Transmission If you move the gearshift lever to a ~ower gear while driving faster than the maximum EXAMPLE allowable speed for the lower gear, the
transmission will not actually downshift
until your speed drops below the maximum
speed for the lower gear.
CAUTION
Be sure to take the following precau­tions to help avoid damage to the
automatic transmission:
• Make sure that the vehicle is com­
pletely stationary before shifting
into "P" or "R". • Do not shift from "P" or "N" to "R", "0" "4" "3" or "L" when the
engine is'runni'ng above idle speed. • Do not rev the engine with the
transmission in a drive position ("R", "0", "4", "3", or "L") and the
rear wheels not moving. • Do not use the accelerator to hold the vehicle on a hill. Use the vehi­
cle's brakes.
3-15
(1) Power mode selector switch
0:
64J141
4-speed automatic transmission mode 3: 3-speed automatic transmission mode
The 3-speed mode is suitable for the fol­
lowing driving conditions: • Driving on hilly, winding roads .
-You can drive more smoothly with less frequent gearshifting • Going down a steep hill -Some engine braking is provided
NOTE: With the transfer switch in the "4L LOCK" position, the 4-speed automatic transmis­sion will remain in the 3-speed mode. Power
mode
selector switch
A/T
POWER
650448
When you need more power for climbing hills or smooth starting on slippery road,
push the "AfT POWER" switch. To activate
the power mode selector, push the "AfT POWER" switch, and the "POWER" indica­tor light in the instrument cl~ster c0n:'es on. To deactivate, push the sWitch again, and
the "POWER" indicator light goes off.
Power driving mode When the "AfT POWER" switch is on with
shift in "0" (Drive) or "3" (Low 3), if you
depress the accelerator pedal, .the shifting
points are delayed so the engine can rev
higher
in each gear. Therefore, yo~. can
drive more powerfully than normal driving.

Downloaded from www.Manualslib.com manuals search engine Slippery road mode
When the "AfT POWER" switch is on with
shift in "2" (Low 2) position, the gear will be
fixed in second while driving or when start
driving. Therefore, you can drive smoothly
on slippery road.
NOTE: • When you start driving with the gearshift lever in "2" (Low 2) position while the "AI T POWER" switch is on, the gear will be fixed in second. If you need to shift up, shift the' lever into "3" (Low 3) or "0" (Drive) position. • When the "AfT POWER" is on, if you
shift the gearshift lever from "3" (Low 3) or "0" (Drive) position to "2" (Low 2) posi­tion, the gear will be fixed in second. Gearshift
lever
64J142
The
gearshift lever is designed that it can­not be shifted out of the "P" position unless
the ignition switch is in the "ON" position and. the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from' "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving
unexpectedly when you shift.
OPERATING YOUR VEHICLE
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use the
other gearshift lever positions as described
below: .
P (Park)
Use this position
to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle,
never leave the transfer switch in "N" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park ..
R (Reverse) Use this position to reverse the vehicle from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral)
Use this position for starting the engine if
the engine
stalls and you need to restart it while the vehicle is moving. You may also
shift into Neutral and depress the brake
pedal to hold the I('ehicle stationary during
idling.
3-16

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
4L LOCK (4-wheel drive low range center differential lock)
000
64J222
3-23
In this position, engine power is supplied to
the front and rear axles and you get better
traction and more low-speed torque than
when driving in "4H". Use this position
when you need better traction than "4H" provides and more low-speed torque than "4H LOCK" provides, such as when climb­ing or descending steep, slippery hills etc.
NOTE: When the transfer switch (if equipped) is
turned to the "4L LOCK" position, the ESfiW systems (other than ABS) (if
equipped) will be canceled to provide
improved vehicle traction, and the "ESP
OFF" indicator light will come on. When the transfer switch (if equipped) is turned to the "4L LOCK" position, brake­traction control can be activated. Brake­traction control brakes the spinning wheel to distribute drive power to the other
wheels for increased climbing ability or for
better performance on
a rolling hill or a slippery surface.
ESP® is a registered trademark of Daimler AG.

Downloaded from www.Manualslib.com manuals search engine To reset the cruise control to a faster
speed, use either of the following proce­
dures:
• Hold in the "RES/ACC" switch (4). Vehi­cle speed will steadily increase. When you release the switch, the new speed will be maintained. • Accelerate· to the desired speed using the accelerator pedal and push the "SET/COAST" switch (3). The new
speed will be maintained.
To Cancel To cancel cruise control operation, use one of the following procedures:
• Slightly depress the brake pedal or clutch pedal, or push the "CANCEL:' switch (2). Cruise control operation will be canceled until you reset a cruising
speed by pushing the "SET/COAST" switch (3) or "RES/ACC" switch (4). • Push the "ON/OFF" switch (1). Cruise control operation will be canceled until you turn on the system by pushing the "ON/OFF" switch (1) again and reset a
cruising speed by pushing the "SET/
COAST" switch (3).
Cruise control operation will also be can­celed any time the vehicle speed falls
below 40 km/h (25 mph).
To "Resume" a Previously Set
Speed
After canceling cruise control operation
without turning off the "ON/OFF" switch (1), you can "resume" a previously set
speed, by holding the "RES/ACC" switch (4) for about one second. When you release the switch, the vehicle will acceler­ate to and maintain the previously set
speed.
NOTE: If the "ON/OFF" switch (1) is turned off, the set speed in the memory is cleared and
you can not use the Resume feature. In this case, reset your CRUISE speed.
OPERATING YOUR VEHICLE
Braking
60G165S
The distance needed to bring any vehicle to a halt increases with the speed of the vehicle. The braking distance needed, for example, at 60 km/h (37 mph) will be approximately 4 times greater than the braking distance needed at 30 km/h (19 mph). Start to brake the vehicle when there is plenty of distance between your vehicle
and the stopping point, and slow down
gradually.
3-30

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
If
water gets into the brake drums,
brake performance may become poor
and unpredictable.
After driving through water or wash­
ing the underside of the vehicle, test
the brakes while driving at a slow speed to see if they have maintained
their normal effectiveness. If the
brakes are less effective than normal, dry them by repeatedly applying the
brakes while driving slowly until the
brakes have regained their normal effectiveness.
Power Assisted Brakes Your vehicle has power assisted brakes. If power assistance is lost due to a stalled engine or other failures, the system is still
fully operational on reserve power and you can bring the vehicle to a complete stop by pressing the brake pedal once and holding it down. The reserve power is partly used
up when you depress the brake pedal and reduces each time the pedal is pressed. Apply smooth and even pressure to the pedal. Do not pump the pedal.
3-31
A WARNING
Even without reserve power in the
brake system, you can still stop the vehicle by pressing the brake pedal harder than normally required. How­ever, the stopping distance may be longer.
Brake Assist System When you slam the brakes on, the brake
assist system judges as an emergency
stop and provides more powerful braking
for a driver who cannot hold down the
brake pedal firmly.
NOTE: If you quickly and forcefully depress the
brakes, you may hear a clicking sound in
the brake pedal. This is normal and indi­
cates that the brake assist system is acti­
vated properly.
Anti-Lock Brake System (ABS) ASS will help you avoid skidding by elec­
tronically controlling braking pressure. It
will also help you maintain steering control when braking on slippery surfaces or when
braking hard.
The
ASS works automatically, so you do
not need any special braking technique.
Just push the brake pedal down without
pumping. The ASS will operate whenever it
senses that the wheels are locking up. You may feel the brake pedal pulsate while the ASS is operating.
NOTE: The ABS will not work if vehicle speed is under about 5 - 6 kmlh (3 - 4 mph).
A WARNING
•
On some types of loose surfaces
(such as gravel, snow-covered
roads, etc.) the stopping distance
required for
an ABS-equipped vehi­cle may be slightly greater than for
a comparable vehicle with a con­ventional brake system. With a conventional brake system, skid­
ding tires are able to "plow" the gravel or snow layer, shortening
the stopping distance, ABS mini­
mizes this resistance effect. Allow for extra stopping distance when driving on loose surfaces. • On regular paved roads, some driv­
ers may be able to obtain slightly shorter stopping distances with
conventional brake systems than
with
ABS. • In both of the above conditions, ABS wi II still offer the advantage of helping you maintain directional control. However, remember that ABS will not compensate for bad road or weather conditions or poor
driver judgment. Use good judg­
ment and do not drive faster than
conditions will
safely allow.