service SUZUKI GRAND VITARA 2016 Service Manual

8-9
EMERGENCY SERVICE
54P00-01E
1) Use only a 12-volt battery to jump-start
your vehicle. Position the good 12-volt
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, check that two vehicles
do not touch each other. Set the park-
ing brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
54P000804
3) Connect jump leads as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of
the flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery
(2).
3. Connect one end of the second jump
lead to the negative (–) terminal of
the booster battery (2).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mount bracket (3)) of the
engine of the vehicle with the flat
battery (1).4) If the booster battery you are using is
fitted to another vehicle, start the
engine of the vehicle with the booster
battery. Run the engine at moderate
speed.
5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
NOTICE
Your vehicle should not be started by
pushing or towing. This starting
method could result in permanent
damage to the catalytic converter.
Use jump leads to start a vehicle with
a weak or flat battery.
(2)
(1)
(3)
EXAMPLE
WA R N I N G
Never connect the jump lead directly
to the negative (–) terminal of the dis-
charged battery, or an explosion may
occur.
CAUTION
Connect the jump lead to the engine
mount bracket securely. If the jump
lead disconnects from the engine
mount bracket because of vibration
at the start of the engine, the jump
lead could be caught in the drive
belts.

8-10
EMERGENCY SERVICE
54P00-01E
Towing
If you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
2-wheel drive (2WD) manual tran-saxle
Manual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the
ground. Before towing, check that the
parking brake is released.
2) From the rear, with the rear wheels
lifted and the front wheels on the
ground, provided the steering and
drivetrain are in operational condition.
Before towing, check that transaxle is in
neutral, the steering wheel is unlocked
(vehicle without keyless push start sys-
tem - the ignition key should be in
“ACC” position) (vehicle with keyless
push start system - the ignition mode is
“ACC”), and the steering wheel is
secured with a clamping device
designed for towing service.
4-wheel drive (4WD)
Your vehicle should be towed under one of
the following conditions:
1) With all four wheels on a flat-bed truck.
2) With the front or rear wheels lifted and a
dolly under the other wheels.
WA R N I N G
For vehicles equipped with the radar
brake support system, if your vehicle
is towed with the engine on, press
radar brake support OFF switch and
turn off the radar brake support sys-
tem. If not, unexpected accidents
related to the system being turned on
may occur.
NOTICE
Observe the following instructions
when towing your vehicle.
• To help avoid damage to your vehi-
cle during towing, proper equip-
ment and towing procedures must
be used.
• Using the frame hook, tow your
vehicle on paved roads for short
distances at low speed.
NOTICE
The steering column is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing. Always unlock the steering
wheel before towing.

8-11
EMERGENCY SERVICE
54P00-01E
Engine trouble: Starter does
not operate
1) Try turning the ignition switch to
“START” position or try pressing the
engine switch to change the ignition
mode to “START” with the headlights
turned on to determine the battery con-
dition. If the headlights go excessively
dim or go off, it usually means that
either the battery is flat or the battery
terminal contact is poor. Recharge the
battery or correct battery terminal con-
tact as necessary.
2) If the headlights remain bright, check
the fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the vehi-
cle inspected by your authorized
SUZUKI dealer.
Engine trouble: Flooded
engine
(Vehicle without keyless push start sys-
tem)
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine.
• For gasoline engine model, do not oper-
ate the starter motor for more than 12
seconds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
(Vehicle with keyless push start sys-
tem)
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine.
• For gasoline engine model, do not oper-
ate the starter motor for more than 12
seconds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
NOTE:
If the engine refuses to start, the starter
motor automatically stops after a certain
period of time. After the starter motor hasautomatically stopped or if there is any-
thing abnormal in the engine starting sys-
tem, the starter motor runs only while the
engine switch is held pressed.

8-12
EMERGENCY SERVICE
54P00-01E
Engine trouble: Overheating
The engine could overheat temporarily
under severe driving conditions. If the
engine coolant temperature gauge indi-
cates overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and
park.
3) Run the engine at a normal idle speed
for a few minutes until the indicator is
within the normal, acceptable tempera-
ture range between “H” and “C”.If the temperature indication does not
come down to within the normal, accept-
able range:
1) Turn off the engine and check that the
water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, correct it.
2) Check the coolant level in the reservoir.
If it is found to be lower than “LOW”
line, check radiator, water pump, radia-
tor hoses and heater hoses for leakage.
If leakage that may cause overheating
is found, do not run the engine until
these problems have been corrected.
3) If leakage is not found, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “Engine
coolant” in “INSPECTION AND MAIN-
TENANCE” section.)
NOTE:
If engine overheats and you are not sure
what to do, contact your SUZUKI dealer.
79J007
WA R N I N G
If you see or hear escaping steam,
stop the vehicle in a safe place and
immediately turn off the engine to
cool it. Do not open the hood when
steam is present. When the steam
can no longer be seen or heard, open
the hood to see if the coolant is still
boiling. If it is, you must wait until it
stops boiling before you proceed.WA R N I N G
• It is hazardous to remove the radia-
tor cap (or degassing tank cap for a
diesel engine) when the water tem-
perature is high, because scalding
fluid and steam may be blown out
under pressure. The cap should
only be taken off when the coolant
temperature has lowered.
• To help prevent personal injury,
keep hands, tools and clothing
away from the engine cooling fan
and air-conditioner fan (if
equipped). These electric fans can
automatically turn on without warn-
ing.

8-13
EMERGENCY SERVICE
54P00-01E
MEMO

10-1
GENERAL INFORMATION
54P00-01E
Vehicle identification
Chassis serial number
63J10468LM101
The chassis and/or engine serial numbers
are used to register the vehicle. They are
also used to assist your dealer when
ordering or referring to special service
information. Whenever you have occasion
to consult your SUZUKI dealer, remember
to identify your vehicle with this number.
Should you find the number difficult to
read, you will also find it on the identifica-
tion plate.
Engine serial number
60G128
The engine serial number is stamped on
the cylinder block as shown in the illustra-
tion.
EXAMPLE
EXAMPLE (for some vehicles)

12-4
SUPPLEMENT
54P00-01E
NOTE:
Oxygenated fuels are fuels which contain
oxygen-carrying additives such as MTBE
or alcohol.
If “RON 95” label is attached, you must use
unleaded gasoline with a minimum rating
of 91 pump octane ((R + M)/2 method).
Gasoline containing MTBE
Unleaded gasoline containing MTBE
(methyl tertiary butyl ether) may be used in
your vehicle if the MTBE content is not
greater than 15%. This oxygenated fuel
does not contain alcohol.
Gasoline-ethanol blends
Blends of unleaded gasoline and ethanol
(grain alcohol), also known as gasohol,
may be used in your vehicle if the ethanol
content is not greater than 10%.
Gasoline-methanol blends
Fuels containing 5% or less methanol
(wood alcohol) may be suitable for use in
your vehicle if they contain cosolvents and
corrosion inhibitors. Do not use fuels con-
taining more than 5% methanol under any
circumstances. Fuel system damage or
vehicle performance problems resulting
from the use of such fuels are not the
responsibility of SUZUKI and may not be
covered under the New Vehicle Limited
Warranty.
Fuel pump labeling
In some states, pumps that dispense oxy-
genated fuels are required to be labeled
for the type and percentage of oxygenate
and whether important additives are pres-
ent. Such labels may provide enough infor-
mation for you to determine if a particular
blend of fuels meets the requirements
listed above. In other areas, pumps may
not be clearly labeled as to the content or
type of oxygenate and additives. If you are
not sure that the fuel you intend to use
meets these requirements, check with the
service station operator or the fuel sup-
plier.
NOTE:
To help clean the air, SUZUKI recom-
mends you use the oxygenated fuels.
However, if you are not satisfied with the
driveability or fuel economy of your vehicle
when you are using an oxygenated fuel,
switch back to the regular unleaded gaso-
line.
Engine oil and filter
Specified oil
“Starburst” symbol
80JC103
Use engine oil for gasoline engines with
the above “Starburst” symbol, certified by
American Petroleum Institute.
We highly recommend you use SAE 0W-20
or 5W-30 oil.
SAE 0W-20 is the best choice for good fuel
economy and good starting in cold
weather.
NOTICE
Be careful not to spill fuel containing
alcohol while refueling. If fuel is
spilled on the vehicle body, wipe it up
immediately. Fuels containing alco-
hol can cause paint damage, which is
not covered under the New Vehicle
Limited Warranty.
NOTICE
Failure to use the recommended oil
can result in engine damage.

54P00-01E
For countries applied for the revised edition since the third edition of UN Regulation No.10
Installation of Radio Frequency (RF) Transmitting Equipment
Your vehicle is conformed to the revised edition since the third edition of UN Regulation No.10.
When you intend to use RF transmitting equipment in your vehicle, we strongly recommend that you select the equipment which
conforms to applicable rules or regulations in your country, and consult your SUZUKI dealer or qualified service technician for advice.
Table : Installing and the use of the on-board RF transmitter equipment
(1) Front
(2) Antenna installation position: Front left of roof
(3) Antenna installation position: Front right of roof
*The illustration is example of hatchback vehicle.Frequency bands (MHz)Antenna position at
vehicle*Maximum output power (W)
144-146 Amateur band
84MM01201
50
430-440 Amateur band 50
1200-1300 Amateur band 10
(2)
(1)
(3)

54P00-01E
No-Using Conditions
- When temperature under -40
.
- On miring or sand ground.
- On big gradient road.
-In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm,thunder-storm, etc.
- Loading dangerous heavy, for instance: melted metal, acidity substance, radioactivity
substance or specially crisp goods.
-Contact with hood directly.
-Using on boat.
-The ground with difference in level.
Operation instructions
Whenever a wheel is changed, always remove any corrosion
that may be present on inside of wheel and wheel mounting
surface on vehicle.
Details:
Please operate according to the “operation instructions”.
Operate the jack on the level ground while checking the jack
and the load.
Mustn’t operate under raising load, unless the load is fastened
surely.
- Park the car on the flat, level ground and apply the brake
firmly.
- Set transmission in “reverse”(automatic transmission in
“park”).
- Turn on the hazard warning flasher.
- Remove jacking tools and spare tire from stowage area.
- Block front and rear of wheel diagonally opposite wheel
being removed before operating jack.
- Loosen, but do not remove wheel nuts by turning wrench counter clockwise.
- Raise jack until jack-head groove fits boss of frame see illustrations.
- Operate jack with slow, smooth motion, using jack handle.
- Raise vehicle so an inflated tire will just clear surface, remove nuts and wheel.
- Install wheel, then slightly tighten each nut, wheel must be seated on hub.
- Lower vehicle, and fully tighten wheel nuts in across-cross sequence by turning wrench
clockwise.
Maintenance
- Please prevent the JACK SCREW from accretion of dirt.
- Check the nameplate, keep the shape same as original.
- No-rejigger the jack’s construction privately.
- After any use, consult immediately your Suzuki Dealer or Service Partner for inspection
and maintenance of the jack.
- If the label (sticker) is damaged, please consult your Suzuki Dealer or Service Partner.
>ö>í>ï>÷>õ>ú>ó>Ì
>ü>û>õ>ú?>Ì
>ö>í>ï>÷>õ>ú>ó>Ì>ü>û>õ>ú?>Ì
>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì>î>í>þ>Ì>ö>í>ï>÷>Ì>ô>í>ú>ð>ø>ñ>Ì

54P00-01E
Delenes betegnelse for Saksedonkraft Se FIG 1 på den engelsksprogede side. Tekniske data og anvendelse Se FIG 2 på den engelsksprogede side.
Betingelser, hvor donkraften ikke må bruges - Temperatur under -40 °C.
- På mudret eller sandet underlag.
- På stærkt hældende veje.
-Under ekstreme vejrforhold: kraftigt regnvejr, tyfon, cyklon, snestorm, tordenvejr mv.
- Tungt eller farligt gods, fx: smeltet metal, syrer, radioaktive stoffer eller særligt skrøbelige varer.
-Direkte kontakt med køretøjets understel.
-På et skib.
-På underlag med niveauforskelle.
BrugsanvisningNår du skifter hjul, skal du altid fjerne eventuel rust,
der måtte findes inde i hjulet eller på køretøjets hjulmonteringsoverflade.
Nærmere anvisninger:
Gå frem ifølge brugervejledningen.
Brug donkraften på et jævnt underlag, og hold øje med både donkraften og
lasten.
Du må ikke foretage indgreb under en løftet last,med mindre lasten er gjort
sikkert fast.
- Parker køretøjet på et fladt, jævnt underlag, og træk bremsen godt.
- Sæt gearkassen i bakgear (en automatisk gearkasse sættes
på ”parkering”).
- Tænd katastrofeblinket.
- Tag donkraftens redskaber og reservehjulet ud af deres
opbevaringsrum.
- Bloker foran og bag på det hjul, der sidder diagonalt i forhold til det hjul,
der fjernes, inden donkraften bruges.
- Løsn hjulmøtrikkerne uden at fjerne dem ved at dreje skruenøglen
mod uret.
- Løft donkraften, indtil rillerne i donkraftens løftebakke passer til rammen - se illustrationerne.
- Betjen donkraften ved hjælp af donkraftens håndtag med langsomme, jævne bevægelser.
- Løft køretøjet, så et oppustet dæk netop vil være frit af underlaget. Fjern møtrikkerne, og tag hjulet af.
- Sæt det nye hjul på plads, og stram hver møtrik lidt. Hjulet skal sidde på et nav.
- Sænk køretøjet ned, og stram hjulmøtrikkerne fuldstændigt skiftevis i en overfor/diagonalt-sekvens ved at
dreje skruenøglen med uret.
Vedligeholdelse - Pas på at undgå, at DONKRAFTENS SKRUE samler snavs.
- Tjek typeskiltet. Bevar den originale form.
- Det er forbudt selv at foretage ændringer på donkraftens konstruktion.
- Efter ethvert brug, skal du øjeblikkeligt konsultere din Suzuki-forhandler eller servicepartner, for eftersyn og
vedligeholdelse af donkraften.
- Hvis mærkaten (etiketten) er beskadiget, skal du rådføre dig med din Suzuki-forhandler eller
servicepartner.
A : LØFTEBAKKE F : DONKRAFTENS SKRUE X : LØFTEHØJDE (mm)
B : BASE G : NOMINEL LØFTEKAPACITET (t) Y : BELASTNING (t)
C : ØVRE ARM H
1: MINIMUMSHØJDE (mm) M : MODEL
D : NEDRE ARM H2: MAKSIMUMSHØJDE (mm) T : TYPE
E : HÅNDTAGETS LED H3 : HØJDE FOR SIKKER BETJENING (mm)
LØFTE-
PUNKT
LØFTEPUNKT
DONKRAFTSTANG HÅNDTAG
DONKRAFT
BRUGSANVISNING
Fabrikanter:
RIKENKAKI CO., LTD. 5-6-12 Chiyoda, Sakado-shi, Saitama, 350-0214 Japan
Tel: 049-248-1661
Fax:049-284-4340
CHANGZHOU RIKENSEIKO MACHINERY CO., LTD. No. 1903 Zhongwu Ave. Zhonglou Changzhou, Jiangsu CHINA
Tel: 0519-327-5284
Fax:0519-327-0811
Læs denne BRUGSANVISNING før brug!
Standard: EN 1494:2000+A1:2008
Advarsel- DONKRAFTEN må kun anvendes til udskiftning af dæk, ikke til andre formål.
- Brug ikke DONKRAFTEN flere end 50 gange.
- Løft aldrig mennesker.
- Kravl aldrig ind under et køretøj, der er løftet med en donkraft.
- Brug af defekte eller utilstrækkeligt vedligeholdte donkrafte, er ekstremt farligt.
Betydning af piktogrammet på advarselsmærket

Dette symbol angiver en mulig fare, der kan medføre dødsfald
eller alvorlig skade.
Dette symbol betyder, at du aldrig må kravle ind under et
køretøj, der er løftet med donkraften.
Orange baggrund
Sort
Sort
Rød Hvid baggrund
Dansk (Danish)