remote start SUZUKI GRAND VITARA 2017 Owner's Manual

3-16
OPERATING YOUR VEHICLE
54P00-01E
(For diesel engine model)
Cold engine
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off up to 10 seconds afterward.
Warm engine
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”.
Caution when stopping the engine with
turbocharger
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.Restarting diesel engine after fuel-
empty stop
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform the above engine starting pro-
cedure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
SUZUKI dealer to have the engine
inspected.
If the master warning indicator light
blinks and the engine cannot be started
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after checking that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. To start the
engine, use the following method:
58MST0302
1) Check that the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) “PUSH START SWITCH.” message will
appear on the information display in the
instrument cluster. Press the engine
switch (1).
4) The master warning indicator light in
the instrument cluster blinks within
about 10 seconds. Touch the engine
switch with “LOCK” button of remote
controller (2) for about 2 seconds.
NOTICE
Do not crank the engine for more
than 30 seconds at a time.
If the engine does not start on the
first try, wait about 15 seconds before
trying again.
(1)
(2)
EXAMPLE

3-17
OPERATING YOUR VEHICLE
54P00-01E
NOTE:
• If you still cannot start the engine after
several attempts using the above
method, there may be a problem else-
where, such as a low battery. Contact
your SUZUKI dealer for inspection.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display will show a certain
message during this time. Refer to
“Information display” in “BEFORE DRIV-
ING” section for details.
• You may customize the system to cause
the interior buzzer to sound once for
warning that remote controller is out of
sensing range. Please contact an autho-
rized SUZUKI dealer for the customiza-
tion.
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to “ON”. For details on
replacing the battery, refer to “Keyless
push start system remote controller /
keyless entry system transmitter” in
“BEFORE DRIVING” section.Returning ignition mode to “LOCK” (OFF)
NOTE:
Certain problems such as a fault in engine
system may prevent the engine switch
from going back to “LOCK” (OFF) mode. If
this happens, have the vehicle inspected
by an authorized SUZUKI dealer after
doing the following:
• Lock the doors using the key to prevent
theft. (The request switches and the key-
less push start system remote controller
cannot be used to lock them.)
• Disconnect the negative cable from the
battery to prevent discharge.“LOCK” (OFF) mode reminder buzzer
The buzzer will stop sounding if you then
push the engine switch twice, thus bringing
back the ignition mode to “LOCK” (OFF).
• If you open the driver’s door after press-
ing the engine switch to change the igni-
tion mode to “ACC”, the interior buzzer
beeps intermittently.
• The buzzer will stop sounding if you then
push the engine switch twice, thus bring-
ing it back the ignition mode to “LOCK”
(OFF).
NOTE:
Whenever you leave the vehicle, check
that you have returned the ignition mode to
“LOCK” (OFF) using the engine switch and
then lock the doors. Without returning the
ignition mode to “LOCK” (OFF), you can-
not use a request switch or keyless push
start system remote controller to lock the
doors.
Steering lock warning buzzer
If the steering lock fails to engage due to a
fault in the system when the ignition mode
is turned to “LOCK” (OFF) by pressing the
engine switch and any door (including the
tailgate) is opened or closed, the interior
buzzer will warn you of this condition with
repeated short beeps. If this happens,
have the vehicle inspected by an autho-
rized SUZUKI dealer.

5-9
OTHER CONTROLS AND EQUIPMENT
54P00-01E
USB socket (if equipped)
54P000512
Connect your portable digital music player,
etc. to this socket to enjoy music through
the vehicle’s audio system. Refer to “Audio
system (Type A / Type B) (if equipped)” in
this section.
Sunroof (if equipped)
You can tilt or slide the sunroof by operating
the sunroof switch after pressing the engine
switch to change the ignition mode to “ON”.
65D612
• Close the sunroof when you leave the
vehicle unattended.
• Periodically inspect the guide rail for dirt
and clean it if any dirt has accumulated.
WA R N I N G
• Never allow any part of your body
such as hands or head to get out of
the sunroof opening while the vehi-
cle is moving.
• Fasten your seat belts and use child
restraints at all times. In an acci-
dent, you could be thrown from the
vehicle through an open sunroof.
• Check that there are no hands or
other obstructions in the path of the
sunroof when you close the sunroof.
• Always take the keyless push start
system remote controller with you
when leaving the vehicle even if
only for a short time. Also do not
leave children alone in a parked
vehicle. Unattended children could
use the sunroof switches and get
trapped by the sunroof.
NOTICE
• Do not put your body weight on the
roof around the sunroof such as by
sitting on it.
• Remove water drops, snow, ice or
sand from the sunroof before open-
ing.

12-5
SUPPLEMENT
54P00-01E
Tire rotation
4-tire rotation
54G114
To avoid uneven wear of your tires and to
prolong their life, rotate the tires as illus-
trated. Tires should be rotated as recom-
mended in the periodic maintenance
schedule. After rotation, adjust front and
rear tire pressures to the specification
listed on your vehicle’s tire information
label.
For European countries,
Mexico and South Africa
Theft deterrent alarm system
A theft deterrent alarm system is armed in
about 20 seconds after you lock the doors.
Keyless push start system – Use the
remote controller or push the request
switch on driver’s door handle, front pas-
senger’s door handle or tailgate.
Keyless entry system – Use the transmit-
ter.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless push start system remote
controller, the request switch, the keyless
entry system transmitter or engine hood
(for EU specification vehicle) will cause the
alarm to be triggered.
* These means include the following:
–The key
– The lock knob on a door
– The power door locking switchNOTE:
The theft deterrent alarm system gener-
ates alarms when any of the predeter-
mined conditions is met. However, the
system does not have any function of
blocking unauthorized entry into your
vehicle.
Always use the keyless push start sys-
tem remote controller, the request switch
or the keyless entry system transmitter
to unlock the doors when the theft deter-
rent alarm system has been armed.
Using a key instead will trigger the
alarm.
If a person who does not know the theft
deterrent alarm system is going to drive
your vehicle, we recommend you explain
the system and its operation to the per-
son, or disable the system beforehand.
Mistakenly triggering the alarm may
cause a nuisance to others.
Even if the theft deterrent alarm system
is armed, you should still be careful to
guard against theft. Do not leave money
or things of value in your vehicle.

12-6
SUPPLEMENT
54P00-01E
How to arm the theft deterrent alarm
system (when enabled)
Lock all doors (including the tailgate) using
the keyless push start system remote con-
troller, the request switch or the keyless
entry system transmitter. The theft deter-
rent light (1) will start blinking, and the theft
deterrent alarm system will be armed in
about 20 seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds.
54P000208
NOTE:
To prevent the alarm from being acciden-
tally triggered, avoid arming it while any-
one remains inside the vehicle. The
alarm will be triggered if any person
inside unlocks a door or engine hood (for
EU specification vehicle) by operating
the lock knob or power door locking
switch.
The theft deterrent alarm system is not
armed when all doors are locked using
the key from outside, or using the door
lock knobs or the power door locking
switch from inside.
If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless push
start system remote controller, the
request switch or the keyless entry sys-
tem transmitter, the doors are automati-
cally locked again. At the same time, the
theft deterrent alarm system is armed if
the system is in the enabled state.How to disarm the theft deterrent alarm
system
Simply unlock the doors using the keyless
push start system remote controller, the
request switch or the keyless entry system
transmitter. The theft deterrent light will go
out, indicating that the theft deterrent
alarm system is disarmed.
(1)

12-7
SUPPLEMENT
54P00-01E
How to stop the alarm
Should the alarm be triggered accidentally,
unlock the doors using the keyless push
start system remote controller, the request
switch or the keyless entry system trans-
mitter, or press the engine switch to
change the ignition mode to “ON” or turn
the ignition switch to “ON” position. The
alarm will then stop.
NOTE:
Even after the alarm has stopped, if you
lock the doors using the keyless push
start system remote controller, the
request switch or the keyless entry sys-
tem transmitter, the theft deterrent alarm
system will be rearmed with a delay of
about 20 seconds.
If you disconnect the battery while the
theft deterrent alarm system is in the
armed condition or the alarm is actually
in operation, the alarm will be triggered
or re-triggered when the battery is then
reconnected, although, in the latter case,
the alarm remains stopped for the period
between disconnection and reconnec-
tion of the battery.
Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any door or
engine hood (for EU specification vehi-
cle) is opened without disarming the
theft deterrent alarm system.Checking whether the alarm has been
triggered during parking
If the alarm was triggered due to an unau-
thorized entry into the vehicle and you then
press the engine switch to change the igni-
tion mode to “ON” or turn the ignition
switch to “ON” position, the theft deterrent
light will blink rapidly for about 8 seconds
and a buzzer will beep 4 times during this
period. If this happens, check whether your
vehicle has been broken into while you
were away from it.
Enabling and disabling the theft deter-
rent alarm system
The theft deterrent alarm system can be
either enabled or disabled.
When enabled (factory setting)
When the system is enabled, it causes the
hazard warning lights to flash for about 40
seconds if any of the alarm trigger condi-
tions is met. The system also causes the
interior buzzer to beep intermittently for
about 10 seconds, which is followed by
intermittent sounding of the horn for about
30 seconds.
The theft deterrent light continues to blink
during this time.
When disabled
When the system is disabled, it stays dis-
armed even if you perform any system
arming operation.How to switch the state of the theft
deterrent alarm system
You can switch the theft deterrent alarm
system from the enabled state to the dis-
abled state, and vice versa, using the fol-
lowing method.
54P000209
(2)(3)
(1)
EXAMPLE

13-3
INDEX
54P00-01E
Fuel gauge ............................................................................ 2-64
Fuel pump labeling .............................................................. 12-4
Fuel recommendation .................................................. 1-1, 12-3
Full wheel cover ..................................................................... 8-5
Fuses .................................................................................... 7-41
Fuses in engine compartment ............................................ 7-41
Fuses under dashboard ...................................................... 7-43
G
Gasoline containing MTBE ................................................. 12-4
Gasoline engine ..................................................................... 1-1
Gasoline-ethanol blends .............................................. 1-1, 12-4
Gasoline-methanol blends ........................................... 1-1, 12-4
Gear oil ................................................................................. 7-30
Gear oil change .................................................................... 7-32
Gear oil level check ............................................................. 7-31
Gearshift indicator ...................................................... 2-71, 3-21
Glove box ............................................................................. 5-12
Glove box light .............................................................. 5-6, 7-55
Glow plug indicator light................................................... 2-100
H
Hazard warning switch ...................................................... 2-110
Head restraints............................................................ 2-23, 2-26
Headlight leveling switch .................................................. 2-108
Heated rear window switch / heated outside
rearview mirror switch ...................................................... 2-115
Heating and air conditioning system ................................. 5-23
Heating system .................................................................... 5-25
Highway driving ..................................................................... 4-3
Hill descent control indicator light..................................... 2-92
Hill descent control switch ................................................. 3-80
Hill descent control system ................................................ 3-79Hill hold control system ...................................................... 3-82
Horn ..................................................................................... 2-115
How ABS works.................................................................... 3-76
I
Ignition key reminder ............................................................. 2-2
Ignition switch ........................................................................ 3-3
Illumination indicator light .................................................. 2-98
Immobilizer system ................................................................ 2-1
Immobilizer/keyless push start system warning light ...... 2-94
Improving fuel economy........................................................ 4-2
Information display ........................................... 2-66, 3-43, 3-46
Inside rearview mirror.......................................................... 2-20
Installation of child restraint with top tether ..................... 2-47
Installation of radio frequency transmitters ...................... 5-39
Installation with ISOFIX type anchorages.......................... 2-46
Installation with lap-shoulder seat belts ............................ 2-45
Instantaneous fuel consumption ........................................ 2-67
Instrument cluster ................................................................ 2-63
Instrument panel pocket...................................................... 5-14
Interior light ...................................................................5-5, 7-54
Interior workable area for engine starting ........................... 3-9
J
Jacking instructions .............................................................. 8-1
Jump-starting instructions.................................................... 8-8
K
Keyless entry system transmitter................................2-6, 2-13
Keyless push start system .................................................... 3-6
Keyless push start system remote controller ..............2-6, 2-7
Keys......................................................................................... 2-1
L
Lap-shoulder belt ................................................................. 2-30