ignition SUZUKI GRAND VITARA 2020 Owners Manual

5-85
OTHER CONTROLS AND EQUIPMENT
54P00-01E
Confirming the Personal Identification
Number (PIN)
When the main power source is discon-
nected such as when the battery is
replaced, etc, it is required to enter the PIN
to operate the unit again.
1) Set the ignition switch to “ACC” posi-
tion or the ignition mode to “ON”.
“SECURITY” will be displayed.
2) Press UP button (3) and the button
numbered [1] of PRESET buttons (2)
simultaneously.
3) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1]
- [4] of PRESET buttons (2).
4) Hold down “TUNE/FLD PUSH
SOUND” knob (4) for 1 second or lon-
ger.
When the same PIN as registered is
entered, the power of the audio system
will be turned off automatically and it
will become operable again.
NOTE:
If an incorrect PIN is entered, “ERROR”
and the total number of incorrect entry
attempts will be displayed.
If an incorrect PIN is entered 10 times or
more, “HELP” will be displayed and the
audio system will become inoperable.

7-1
INSPECTION AND MAINTENANCE
54P00-01E
60B128S
WA R N I N G
Take extreme care when working on
your vehicle to prevent accidental
injury. Carefully observe the follow-
ing precautions:
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, check
that the battery is disconnected and
the ignition switch has been in
“LOCK” position or the ignition
mode has been “LOCK” (OFF) for at
least 90 seconds before performing
any electrical service work on your
SUZUKI vehicle. Do not touch air
bag system components, seat belt
pretensioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
(Continued)
WA R N I N G
(Continued)
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
• When it is necessary to perform
service work with the engine run-
ning, check that the parking brake
is set fully and the transaxle is in
Neutral.
• Do not touch ignition wires or other
ignition system parts when starting
the engine or when the engine is
running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
(Continued)
WA R N I N G
(Continued)
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.

7-13
INSPECTION AND MAINTENANCE
54P00-01E
For Mexico
Recommended maintenance items by an authorized SUZUKI dealer or a qualified service technician
#1: Inspect every 100000 km (60000 miles) or 60 months for 1st time and 2nd time.
Inspect every 50000 km (30000 miles) or 30 months for 3rd time, by a shorter interval.
These inspection intervals will be repeated after 4th time.
For details, refer to the following maintenance timing.
1st: 100000 km (60000 miles) or 60 months 2nd: 200000 km (120000 miles) or 120 months 3rd: 250000 km (150000 miles) or 150 months
4th: 350000 km (210000 miles) or 210 months 5th: 450000 km (270000 miles) or 270 months 6th: 500000 km (300000 miles) or 300 months
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months, which-
ever comes first.
miles (×1000)67.5121522.53037.5456090km (×1000)1012.5202537.55062.575100150months67.5121522.53037.5456090Engine and powertrain
Valve lash (clearance)I
Cooling system hoses and connections NormalI
SevereI
Exhaust pipes and mountings NormalISevereI
Drive axle boots NormalISevereI
Manual transaxle oil Genuine
“SUZUKI GEAR OIL 75W-80”NormalIRSevereIR
Other than
“SUZUKI GEAR OIL 75W-80”NormalIRSevereR
Fuel and emission control system
Emission-related hoses & tubes NormalI(#1)
SevereI
Ignition coil (plug cap)I
Fuel tank & capI
Fuel filterReplace every 250000 km (150000 miles) or 150 months.
Fuel lines and connections Normal
I
SevereI

7-15
INSPECTION AND MAINTENANCE
54P00-01E
NOTE:
*1:Clean more frequently if the air flow from the air conditioner decreases.
The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform recom-
mended maintenance items enclosed with a rectangle will not nullify the emission warranty or limit recall liability prior to the completion of
the vehicle’s useful life. SUZUKI, however, urges that all recommended maintenance services be performed at the indicated intervals
and the maintenance recorded.
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months,
whichever comes first.
miles (×1000)67.51530km (×1000)1012.52550months67.51530Chassis, body and others
Steering system Steering wheel linkage NormalISevereI
Air conditioner filter element (if equipped) *1 NormalIRSevereIR
For gasoline engine models
Select maintenance timing by mileage (odometer reading) or months, which-
ever comes first.
miles (×1000)15 30 45 60 75 90 105 120 135 150
km (×1000) 25 50 75 100 125 150 175 200 225 250
months 15 30 45 60 75 90 105 120 135 150
Items
Cooling system hoses and connectionIExhaust pipes and mountingsIIII
Emission-related hoses & tubesIIIgnition coil (plug cap)IIII
Fuel tank & capIIIIIIIII
Fuel line and connectionIIII

7-29
INSPECTION AND MAINTENANCE
54P00-01E
(For diesel engine model)
61MM0A126
1) Unclamp the side clamps and remove
the element from the air cleaner case. If
it appears to be dirty, replace it with a
new one.
2) Clamp the side clamps securely.
Spark plugs
Spark plug replacement and inspec-
tion
(For gasoline engine model)
80JM125
To access the spark plug:
1) Remove the air cleaner case. Refer to
“Air cleaner” in this section.
2) If necessary, disconnect the coupler (1)
while pushing the release lever.
3) Remove the bolts.
4) Pull out the ignition coils straight.NOTE:
During installation, check that the wires,
couplers, sealing rubber of air cleaner
chassis and washers, are correctly
returned in place.
78K179
(1)
EXAMPLE
NOTICE
• When pulling out the ignition coils,
do not pull on the cable. Pulling on
the cable can damage it.
• When servicing the iridium/plati-
num spark plugs (slender center
electrode type plugs), do not touch
the center electrode, as it is easy to
be damaged.
EXAMPLE
Correct Wrong

7-41
INSPECTION AND MAINTENANCE
54P00-01E
Fuses
Your vehicle has three types of fuses, as
described below:
Main fuse
The main fuse takes current directly from
the battery.
Primary fuses
These fuses are between the main fuse
and individual fuses, and are for electrical
load groups.
Individual fuses
These fuses are for individual electrical cir-
cuits.
To remove a fuse, use the fuse puller pro-
vided in the fuse box.
63J095
Fuses in engine compartment
61MM0B068
54P00070654P000707
(1)
(2)
(3)
(4)
(5)(6)
(7)
(8) (20)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)(21)
(22)
(23)
(24)
(25)
(26)(33)
(34)
(35)
(27)
(28)
(29)(36)
(30)(37) (31)
(32)
(38)
(39)
(40)
(41)
(42)
MAIN FUSE / PRIMARY FUSE
(1)50 A FL7 (GAS)
60 A FL7 (DIESEL)
(2)50 A FL6 (GAS)
80 A FL6 (DIESEL)
(3)
100 AFL5
(4)
80 AFL4
(5)
100 AFL3
(6)
60 AFL2 (GAS)
100 AFL2 (DIESEL)
(7)
100 AFL1 (GAS)
120 AFL1 (DIESEL)
(8) 7.5 A Ignition-1 signal 2
(43) (44) (45)

7-42
INSPECTION AND MAINTENANCE
54P00-01E
The main fuse, primary fuses and some of the
individual fuses are located in the engine
compartment. If the main fuse blows, no elec-
trical component will function. If a primary fuse
blows, no electrical component in the corre-
sponding load group will function. When
replacing the main fuse, a primary fuse or an
individual fuse, use a genuine SUZUKI
replacement.To remove a fuse, use the fuse puller pro-
vided in the fuse box. The amperage of each
fuse is shown in the back of the fuse box
cover. (9) 30 A Radiator fan 2
(10) 20 A Front fog light
(11) 7.5 A Headlight 2
(12) 25 A Headlight 3
(13) 25 A ESP
® control module
(14) 25 A Headlight
(15) 30 A Back up
(16) 30 A DCDC 2
(17) 40 A Ignition switch
(18) 40 A ESP
® motor
(19) 30 A Starting motor
(20) 7.5 A Transaxle 3
(21) 30 A Fuel heater
(22) 30 A Radiator fan
(23) 30 A Transaxle 2
(24) 40 A HY pump
(25) 30 A DCDC
(26) 30 A FI main (DIESEL)
(27) 20 AFI (GAS)
Fuel pump (DIESEL)
(28) 10 A Air compressor
(29) 15 A Transaxle 1
(30) 30 A Blower fan
(31) 15 A Transaxle 4
(32) 15 A Transaxle 5
(33) 7.5 A Starting signal
(34) 15 A Headlight (Left)
(35) 15 A Headlight high (Left)
(36) 7.5 A FI 2 (DIESEL)
(37) 20 A INJ DRV
(38) 15 A FI
(39) 15 A Headlight (Right)
(40) 15 A Headlight high (Right)
(41) 50 AIgnition switch 2
(DIESEL)
(42) 50 A Battery (DIESEL)
(43) 40 A Sub heater (DIESEL)
(44) 40 A Sub heater 3 (DIESEL)
(45) 40 A Sub heater 2 (DIESEL)

7-44
INSPECTION AND MAINTENANCE
54P00-01E
81A283
Headlight aiming
Since special procedures are required, ask
your authorized SUZUKI dealer for this job. (12) 7.5 A BCM
(13) 15 A Ignition coil
(14) 10 A ABS control module
(15) 15 A Accessory socket
(16) 10 A A-STOP controller
(17) 15 A Horn
(18) 10 A Stop light
(19) 10 A Air bag
(20) 10 A Back-up light
(21) 15 A Wiper / Washer
(22) 30 A Front wiper
(23) 10 A Dome light
(24) 15 A 4WD
(25) 7.5 A RR fog lamp
(26) – Blank
(27) 7.5 A Ignition-1 signal
(28) 15 A Radio 2
(29) 10 A Accessory socket 3
(30) 15 A Radio
(31) 10 A Tail light
(32) 20 A D/L
(33) 7.5 A Cruise control
(34) 10 A Meter
(35) 7.5 A Ignition-2 signal
(36) 20 A Seat heater
WA R N I N G
Always replace a blown fuse with a
fuse of the correct amperage. Never
use a substitute such as aluminum
foil or wire to replace a blown fuse. If
you replace a fuse and the new one
blows in a short period of time, you
may have a major electrical problem.
Have your vehicle inspected immedi-
ately by your SUZUKI dealer.
BLOWN OK

8-10
EMERGENCY SERVICE
54P00-01E
Towing
If you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
2-wheel drive (2WD) manual tran-saxle
Manual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the
ground. Before towing, check that the
parking brake is released.
2) From the rear, with the rear wheels
lifted and the front wheels on the
ground, provided the steering and
drivetrain are in operational condition.
Before towing, check that transaxle is in
neutral, the steering wheel is unlocked
(vehicle without keyless push start sys-
tem - the ignition key should be in
“ACC” position) (vehicle with keyless
push start system - the ignition mode is
“ACC”), and the steering wheel is
secured with a clamping device
designed for towing service.
4-wheel drive (4WD)
Your vehicle should be towed under one of
the following conditions:
1) With all four wheels on a flat-bed truck.
2) With the front or rear wheels lifted and a
dolly under the other wheels.
WA R N I N G
For vehicles equipped with the radar
brake support system, if your vehicle
is towed with the engine on, press
radar brake support OFF switch and
turn off the radar brake support sys-
tem. If not, unexpected accidents
related to the system being turned on
may occur.
NOTICE
Observe the following instructions
when towing your vehicle.
• To help avoid damage to your vehi-
cle during towing, proper equip-
ment and towing procedures must
be used.
• Using the frame hook, tow your
vehicle on paved roads for short
distances at low speed.
NOTICE
The steering column is not strong
enough to withstand shocks trans-
mitted from the front wheels during
towing. Always unlock the steering
wheel before towing.

8-11
EMERGENCY SERVICE
54P00-01E
Engine trouble: Starter does
not operate
1) Try turning the ignition switch to
“START” position or try pressing the
engine switch to change the ignition
mode to “START” with the headlights
turned on to determine the battery con-
dition. If the headlights go excessively
dim or go off, it usually means that
either the battery is flat or the battery
terminal contact is poor. Recharge the
battery or correct battery terminal con-
tact as necessary.
2) If the headlights remain bright, check
the fuses. If the reason for failure of the
starter is not obvious, there may be a
major electrical problem. Have the vehi-
cle inspected by your authorized
SUZUKI dealer.
Engine trouble: Flooded
engine
(Vehicle without keyless push start sys-
tem)
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine.
• For gasoline engine model, do not oper-
ate the starter motor for more than 12
seconds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
(Vehicle with keyless push start sys-
tem)
If the engine is flooded with gasoline, it
may be hard to start. If this happens, press
the accelerator pedal all the way to the
floor and hold it there while cranking the
engine.
• For gasoline engine model, do not oper-
ate the starter motor for more than 12
seconds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
NOTE:
If the engine refuses to start, the starter
motor automatically stops after a certain
period of time. After the starter motor hasautomatically stopped or if there is any-
thing abnormal in the engine starting sys-
tem, the starter motor runs only while the
engine switch is held pressed.