indicator SUZUKI GRAND VITARA 2022 Owner's Guide

2-86
BEFORE DRIVING
54P00-01E
Warning and indicator
messageMaster warning
indicator lightSound Cause and remedy
ESP
®
61MM0A178
Blinks Beep (one time from interior
buzzer) There may be a problem with ESP® sys-
tem.
Have your vehicle inspected by an autho-
rized SUZUKI dealer.
Hill Hold Control System
61MM0A179
Blinks Beep (one time from interior
buzzer) There may be a problem with hill descent
control system (if equipped) and hill hold
control system.
Have your vehicle inspected by an autho-
rized SUZUKI dealer.

2-87
BEFORE DRIVING
54P00-01E
NOTE:
• When you operate the four-mode 4WD system (if equipped), the information display may show messages other than those in the
above chart. Refer to “Four-mode 4WD system (if equipped)” in “OPERATING YOUR VEHICLE” section for details.
• If your vehicle is equipped with a parking sensor system, the information display also indicates warning and indicator messages
related to the system. For information on these messages, refer to “Parking sensors (if equipped)” in “OPERATING YOUR VEHICLE”
section.
• If your vehicle is equipped with the radar brake support system, the information display also indicates warning and indicator messages
related to the system. For information on these messages, refer to “Radar brake support system (if equipped)” in “OPERATING YOUR
VEHICLE” section.
• If your vehicle is equipped with the adaptive cruise control system, the information display also indicates warning and indicator mes-
sages related to the system. For information on these messages, refer to “Adaptive cruise control system (if equipped)” in “OPERAT-
ING YOUR VEHICLE” section.Warning and indicator
messageMaster warning
indicator lightSound Cause and remedy
61MM0A180
Blinks Beep (one time from interior
buzzer) If this message is displayed, have your
vehicle inspected by an authorized SUZUKI
dealer.

2-88
BEFORE DRIVING
54P00-01E
Warning and indicator lights
NOTE:
If warning and indicator lights blink or
come on, the corresponding messages
may be shown on the information display.
Low tire pressure warning light
(if equipped)
52D305
As an added fuel efficiency feature, your
vehicle is equipped with a tire pressure
monitoring system (TPMS) that uses a low
tire pressure warning light to inform you
when one or more of your tires is signifi-
cantly under-inflated.
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When the low tire pressure warning light is
lit, one or more of your tires is significantly
under-inflated. You should stop and check
your tires as soon as possible, and inflate
them to the proper pressure as indicatedon the vehicle’s tire information placard.
Driving on a significantly under-inflated tire
causes the tire to overheat and can lead to
tire failure. Under-inflation also reduces
fuel efficiency and tire tread life, and may
affect the vehicle’s handling and stopping
ability. Each tire, including the spare,
should be checked at least once a month
when cold and set to the recommended
inflation pressure as specified in the vehi-
cle placard.
The low tire pressure warning light is also
used to inform you of a TPMS malfunction.
When the system detects a malfunction,
this light will blink for about 75 seconds
and then remain continuously illuminated.
This sequence will be repeated after the
ignition switch is turned to “ON” position or
the engine switch is pressed to change the
ignition mode to “ON” as long as the mal-
function exists.
NOTE:
The low tire pressure warning light may not
come on immediately if you have a sudden
loss of air pressure.
WA R N I N G
Failure to take corrective action when
the low tire pressure warning light is
not working or when it comes on and
blinks while driving can lead to an
accident.
If the low tire pressure warning light
does not come on for 2 seconds after
the ignition switch is turned to “ON”
position or the engine switch is
pressed to change the ignition mode
to “ON”, or comes on and blinks
while driving, have your vehicle
inspected by an authorized SUZUKI
dealer. Even if the light turns off after
blinking, indicating that the monitor-
ing system has recovered, you
should still have the system checked
by your authorized SUZUKI dealer.

2-92
BEFORE DRIVING
54P00-01E
ESP® OFF indicator light
57L30045
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When the ESP
® OFF switch is pushed to
turn off the ESP® systems (other than
ABS), the ESP® OFF indicator light comes
on and stays on.
For details of the ESP
® systems, refer to
“Electronic stability program (ESP®)” in
“OPERATING YOUR VEHICLE” section.
Hill descent control indicator light (if equipped)
79K050
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When you push the hill descent control
switch and the hill descent control operat-
ing conditions are fulfilled, the hill descent
control indicator comes on. If the hill
descent control indicator blinks, the hill
descent control will not be activated.
For details of the hill descent control sys-
tem, refer to “Hill descent control system (if
equipped)” in “OPERATING YOUR VEHI-
CLE” section.
Oil pressure light
50G051
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on. When the engine is started, the
light goes out. The light will come on and
remain on if there is insufficient oil pres-
sure. If the light comes on when driving,
pull off the road as soon as you can and
stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your SUZUKI
dealer before you drive the vehicle again.
NOTICE
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the oil pressure light
to indicate the need to add oil. Peri-
odically check the engine oil level.

2-94
BEFORE DRIVING
54P00-01E
Malfunction indicator light
65D530
Your vehicle has a computer-controlled
emission control system. A malfunction
indicator light is provided on the instrument
cluster to indicate when it is necessary to
have the emission control system serviced.
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on. When the engine is started, the
light goes out.
If the malfunction indicator light comes on
or blinks when the engine is running, there
is a damage in the emission control sys-
tem.
Bring the vehicle to your SUZUKI dealer to
have the damage fixed.
(For EU specification vehicle)
Also, if this light comes on when the
engine is running, there is a problem with
the continuously variable transaxle sys-
tem. Ask your SUZUKI dealer to have the
system inspected.
Immobilizer/keyless push start sys-tem warning light
80JM122
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working. If this light stays on, there
is a problem with the system.
Open door warning light
54G391
This light remains on until all doors (includ-
ing the tailgate) are completely closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors completely.
NOTICE
Continuing to drive the vehicle when
the malfunction indicator light is on
or blinking can cause permanent
damage to the vehicle’s emission
control system, and can affect fuel
economy and driveability.

2-96
BEFORE DRIVING
54P00-01E
Radar brake support system indica-tor light (if equipped)
54P000255
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When the brake support system is acti-
vated, this light blinks rapidly.
In the following situations, this light will come
on and the radar brake support system will
stop functioning when the ignition switch is
in “ON” position or the ignition mode is “ON”.
• When there is a problem with the radar
brake support system. In this case, you
should have the system inspected by an
authorized SUZUKI dealer.
• When dirt is detected on the surface of
the radar sensor cover. In this case,
clean the cover.
• When there is a problem with the ABS or
ESP
®. The ABS warning light or the
ESP® warning light will also come on.• When there is a problem with the brake
control systems.
For details, refer to “Radar brake support
system (if equipped)” in “OPERATING
YOUR VEHICLE” section.
Radar brake support system OFF indicator light (if equipped)
54P000254
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
In the following situations, this light will come
on and the radar brake support system will
stop functioning when the ignition switch is
in “ON” position or the ignition mode is “ON”.
• When the radar brake support OFF
switch is pushed and held to turn off the
radar brake support system.
• When the ESP
® OFF switch is pushed to
turn off the ESP® systems (other than
ABS), the ESP® OFF indicator light will
also come on.
For details, refer to “Radar brake support
system (if equipped)” in “OPERATING
YOUR VEHICLE” section.

2-97
BEFORE DRIVING
54P00-01E
Adaptive cruise control system warning light (if equipped)
54P000233
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light stays on, there is a problem with
the adaptive cruise control system. Have
the system inspected by your SUZUKI
dealer.
Automatic headlight leveling system warning light (if equipped)
64J046
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light comes on, there is a problem
with the automatic headlight leveling sys-
tem. Bring the vehicle to your SUZUKI
dealer to have the problem corrected.
Rear fog light indicator light
(if equipped)
54G491
The rear fog light indicator light comes on
when the rear fog light operates.
LED headlight warning light (if equipped)
54P000234
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light comes on, there is a problem
with the LED headlight. Park the vehicle in
a safe place and consult your SUZUKI
dealer to have the problem corrected.

2-98
BEFORE DRIVING
54P00-01E
Turn signal indicators
50G055
When you turn on the left or right turn sig-
nals, the corresponding green arrow on the
instrument cluster will flash along with the
respective turn signal lights. When you
turn on the hazard warning switch, both
arrows will flash along with all of the turn
signal lights.
Main beam (high beam) indicator
light
50G056
This indicator comes on when headlight
main beams (high beams) are turned on.
Illumination indicator light
64J045
This indicator light comes on while the
position lights, tail light and/or the head-
lights are on.
4WD warning light (if equipped)
57L30042
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
• This light comes on if there is any prob-
lem with the four-mode 4WD system.
The system will be deactivated automati-
cally.
• The light blinks if the vehicle is in either
of the following conditions, and the sys-
tem will be deactivated automatically.
– Wheels of different diameters are fitted
to the vehicle.
– Drive train components overheat as a
result of spinning of a drive wheel in
mud or snow.
NOTE:
Should the light blink, immediately move
the vehicle to a safe place and park it there
to protect the drive train components. If
you let the engine run at idle for a while
except for the case of different sized
wheels are fitted, the light will go out and
the system will resume.

2-100
BEFORE DRIVING
54P00-01E
Whenever the engine oil and oil filter are
changed, the light must be reset to monitor
the next oil change timing properly. To
reset the light, consult your SUZUKI
dealer.
NOTE:
• Note that engine oil degrades faster
under the following conditions:
– Mainly urban use of the vehicle,
requiring more frequent regeneration
of the DPF
®;
– Use of the vehicle for short drives, in
which the engine does not have time
to reach its regular operating tem-
perature;
– Repeated interruptions to the regen-
eration process signaled by the DPF
®
warning light coming on.
• Since special procedures and tools are
required, ask your authorized SUZUKI
dealer to reset the oil life monitoring sys-
tem for diesel engine.
Glow plug indicator light (for diesel engine model)
60A543
If the coolant temperature is cool enough,
this light comes on when the ignition
switch is turned to “ON” position or the
engine switch is pressed to change the
ignition mode to “ON” and goes out when
the glow plug is heated enough for engine
starting.
Fuel filter warning light (for diesel engine model)
60A541
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on for several seconds so you can
check that the light is working.
If the light comes on when driving, it is pos-
sible that water may be in the fuel filter.
Drain water as soon as possible. Have
your vehicle inspected by an authorized
SUZUKI dealer.
NOTICE
Severe engine damage will result, if
you keep operating the engine after
this light blinks.
Change the engine oil and oil filter
immediately when the light blinks.

2-101
BEFORE DRIVING
54P00-01E
Diesel particulate filter (DPF®)
warning light (for diesel engine
model)
64J244
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on for several seconds so you can
check that the light is working. If the light
comes on when driving, the DPF
® is nearly
clogged. To turn off the warning light, the
vehicle must stay in motion until regenera-
tion has been completed.
The process normally takes about 25 min-
utes.
The optimum condition for ending the pro-
cess are achieved by keeping the vehicle
in motion at a speed of 50 km/h (31 mph)
or higher, or an engine speed higher than
2,000 rpm.
If you drive your vehicle until the light goes
out, the regeneration of the DPF
® will be
completed.
For details of the DPF
®, refer to “Diesel
particulate filter (DPF®) (For diesel enginemodel)” in “OPERATING YOUR VEHICLE”
section.
“ENG A-STOP” indicator light
(if equipped)
72M00032
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When the engine is stopped by “ENG A-
STOP” system, this light comes on.
For details, refer to “ENG A-STOP system
(engine auto stop start system) (if
equipped)” in “OPERATING YOUR VEHI-
CLE” section.
“ENG A-STOP OFF” light (if equipped)
72M00159
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
When you push “ENG A-STOP OFF”
switch, this light comes on.
If this light blinks when driving, there may
be something wrong with “ENG A-STOP”
system. You should have the system
inspected by an authorized SUZUKI
dealer.
For details, refer to “ENG A-STOP system
(engine auto stop start system) (if
equipped)” in “OPERATING YOUR VEHI-
CLE” section.
NOTICE
Regenerate the DPF® when the DPF®
warning light comes on.
Failure to regenerate the DPF® will
cause the vehicle malfunction due to
the clogged filter.