cruise control SUZUKI GRAND VITARA 2022 Owners Manual

ILLUSTRATED TABLE OF CONTENTS
54P00-01E
1. Adaptive cruise control switch
(if equipped) (P.3-35)/
Cruise control switches
(if equipped) (P.3-42)/
Speed limiter switches
(if equipped) (P.3-45)
2. Instrument cluster (P.2-63)/
Information display (P.2-66)
3. Windshield wiper and washer lever
(P.2-110)/
Rear window wiper/
washer switch (P.2-113)
4. Audio (if equipped) (P.5-40)
5. Hazard warning switch (P.2-110)
6.
Front passenger air bag deactivation
system indicator (if equipped) (P.2-60)/
Theft deterrent alarm system
(if equipped) (P.12-5)/Theft deterrent
light (if equipped) (P.2-16)
7. Fuses (P.7-43)
8. Ignition switch (vehicle without
keyless push start system) (P.3-3)
9. Engine switch (vehicle with keyless
push start system) (P.3-5)
10. Gearshift lever (P.3-19)
11. Front seat heater switch
(if equipped) (P.2-23)
12. USB socket (if equipped) (P.5-9)
13. Accessory socket (P.5-8)
14. Heating and air conditioning
system (P.5-23)/
Heated rear window switch / heated
outside rearview mirrors switch
(if equipped) (P.2-115)
15. Clock (if equipped) (P.5-15)
54P000008
16
75
89
10 11 12 13 1415 234EXAMPLEVIEW C

2-87
BEFORE DRIVING
54P00-01E
NOTE:
• When you operate the four-mode 4WD system (if equipped), the information display may show messages other than those in the
above chart. Refer to “Four-mode 4WD system (if equipped)” in “OPERATING YOUR VEHICLE” section for details.
• If your vehicle is equipped with a parking sensor system, the information display also indicates warning and indicator messages
related to the system. For information on these messages, refer to “Parking sensors (if equipped)” in “OPERATING YOUR VEHICLE”
section.
• If your vehicle is equipped with the radar brake support system, the information display also indicates warning and indicator messages
related to the system. For information on these messages, refer to “Radar brake support system (if equipped)” in “OPERATING YOUR
VEHICLE” section.
• If your vehicle is equipped with the adaptive cruise control system, the information display also indicates warning and indicator mes-
sages related to the system. For information on these messages, refer to “Adaptive cruise control system (if equipped)” in “OPERAT-
ING YOUR VEHICLE” section.Warning and indicator
messageMaster warning
indicator lightSound Cause and remedy
61MM0A180
Blinks Beep (one time from interior
buzzer) If this message is displayed, have your
vehicle inspected by an authorized SUZUKI
dealer.

2-97
BEFORE DRIVING
54P00-01E
Adaptive cruise control system warning light (if equipped)
54P000233
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light stays on, there is a problem with
the adaptive cruise control system. Have
the system inspected by your SUZUKI
dealer.
Automatic headlight leveling system warning light (if equipped)
64J046
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light comes on, there is a problem
with the automatic headlight leveling sys-
tem. Bring the vehicle to your SUZUKI
dealer to have the problem corrected.
Rear fog light indicator light
(if equipped)
54G491
The rear fog light indicator light comes on
when the rear fog light operates.
LED headlight warning light (if equipped)
54P000234
When the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON”, this light
comes on briefly so you can check that the
light is working.
If this light comes on, there is a problem
with the LED headlight. Park the vehicle in
a safe place and consult your SUZUKI
dealer to have the problem corrected.

OPERATING YOUR VEHICLE
3
54P00-01E
60G408
OPERATING YOUR VEHICLE
Exhaust gas warning .......................................................... 3-1
Daily inspection checklist .................................................. 3-1
Engine oil consumption ..................................................... 3-2
Ignition switch
(vehicle without keyless push start system) .................... 3-3
Engine switch
(vehicle with keyless push start system) .......................... 3-5
Keyless push start system (if equipped) .......................... 3-6
Parking brake lever ............................................................. 3-10
Pedal ..................................................................................... 3-11
Starting engine
(vehicle without keyless push start system) .................... 3-12
Starting engine
(vehicle with keyless push start system) .......................... 3-14
Using transaxle ................................................................... 3-19
Gearshift indicator .............................................................. 3-21
Four-mode 4WD system (if equipped) .............................. 3-23
ENG A-STOP system
(engine auto stop start system) (if equipped) .................. 3-29
Adaptive cruise control system (if equipped) .................. 3-32
Cruise control (if equipped) ............................................... 3-42
Speed limiter (if equipped) ................................................. 3-45
Radar brake support system (if equipped) ....................... 3-47
Emergency stop signal (ESS) (if equipped) ...................... 3-63
Parking sensors (if equipped) ............................................ 3-64
Rearview camera (if equipped) .......................................... 3-71
Braking ................................................................................. 3-74
Electronic stability program (ESP®) ................................. 3-76
Tire pressure monitoring system (TPMS) (if equipped) .. 3-83

3-21
OPERATING YOUR VEHICLE
54P00-01E
Gearshift indicator
61MM0A133
(1) Gearshift indicator
In the following cases, the gearshift indica-
tor is indicated on the information display
when the ignition switch is in “ON” position
or the ignition mode is “ON”.
• When the gearshift lever is in a position
other than “N” (Neutral).
• For vehicles equipped with the cruise
control, when the system is not in use.The electronic control system monitors
driving conditions (such as vehicle speed
and/or engine revolution), and it shows
which gear position is appropriate for your
driving with the indication on the display.
If the UP/DOWN arrow and a gear position
other than what is currently selected are
indicated on the display while driving, we
recommend that you shift the gear up or
down to indicated position. This is the
appropriate gear position for a driving con-
dition that reduces the over revolution and
stress to the engine, and improves fuel
consumption.
For details on how to use the transaxle,
refer to “Using transaxle” in this section.NOTE:
• The gearshift indicator is not indicated
when the gear position is in “N” (Neu-
tral).
• If you depress the clutch pedal while UP/
DOWN arrow is indicated, the indication
will disappear.
• In ordinary driving, UP arrow will disap-
pear when you release your foot from
the accelerator pedal.
If your vehicle is equipped with the adap-
tive cruise control and while it is working,
however, UP/DOWN arrow may be indi-
cated continuously depending on driv-
ing conditions. It means that the
indicated gear position is appropriate for
the current cruising speed.
• The indication of gearshift indicator tim-
ing may differ depending on the vehicle
condition and/or driving situation even in
the same vehicle speed and engine rev-
olution.
• If any of the electrical systems such as
the radar brake support system or the
ESP
® is working, the gearshift indicator
will disappear temporarily.
(1)
EXAMPLE
WA R N I N G
The gearshift indicator is designed to
indicate the appropriate gear position
for your driving, however, this indica-
tor does not relieve the driver of any
responsibility to operate gear
changes attentively.
To drive safely, do not focus your
attention on the gearshift indicator,
pay attention to your driving situation
and shift up or down if necessary.

3-32
OPERATING YOUR VEHICLE
54P00-01E
To deactivate ENG A-STOP system
61MM0A101
Push “ENG A-STOP OFF” switch. “ENG
A-STOP OFF” light will come on.
“ENG A-STOP OFF” light
If “ENG A-STOP OFF” light blinks when
driving, there may be something wrong
with the ENG A-STOP system. You should
have the system inspected by an autho-
rized SUZUKI dealer. For details, refer to
“Warning and indicator lights” in “BEFORE
DRIVING” section.
Adaptive cruise control
system (if equipped)
The adaptive cruise control system allows
you to maintain a steady speed without
keeping your foot on the accelerator pedal.
You can use the adaptive cruise control
system under the following conditions:
• Driver’s seat belt is fastened.
• Open door warning light is off.
• Parking brake is completely released.
• Speed limiter is not used.
• The gear position is in 3rd, 4th, 5th or
6th (if equipped).
• The vehicle speed is about 40 km/h (25
mph) or higher.
• ESP
® OFF switch is not pushed and the
system is not turned off.The adaptive cruise control system has the
following four controls.
(1) Constant-speed control
(There is no vehicle ahead)
54P000342
Your vehicle cruises at the set speed.
• The vehicle speed can be set between
40 km/h (25 mph) to 160 km/h (100
mph).
EXAMPLE
WA R N I N G
Deceleration control by the adaptive
cruise control system is limited.
Therefore, you are requested to pay
enough attention for safety driving,
by checking the surrounding traffic
always and operating brake pedal
and/or accelerator pedal as neces-
sary.
EXAMPLE

3-33
OPERATING YOUR VEHICLE
54P00-01E
(2) Deceleration control
(A vehicle ahead is within radar range
and going slower than the set speed)
54P000343
Your vehicle slows down, and maintains
the same speed as the speed of the vehi-
cle ahead to maintain the following dis-
tance.
• Possible detecting distance between
your vehicle and a vehicle ahead is
within about 100 m (328 ft).
(3) Following control
(A vehicle ahead is within radar range
and going at a steady speed)
54P000344
Your vehicle follows the vehicle ahead,
keeping a constant distance, without
exceeding the set speed.NOTE:
• When your vehicle is getting close to the
vehicle ahead while deceleration control
or following control is functioning, a fron-
tal collision warning is activated.
• When operating brake pedal during fol-
lowing control, you might feel that a
brake is heavy. However, this is normal
in the brake system. This occurs
because of the feature of adaptive cruise
control system.
(4) Acceleration control
(A vehicle ahead goes out of range)
54P000345
The adaptive cruise control system accel-
erates your vehicle to the set speed, and
then maintains it.
Situations where radar will not acti-vate properly
Under the following situations, there is a
high possibility that deceleration control,
following control and acceleration control
will not function properly, even if a vehicle
ahead is within radar range.
• When vehicle is driven in a traffic jam
• When vehicle is driven on sharp curves
• When vehicle is driven on slippery road
such as ice or snow-covered road
• When vehicle is driven on steep hill
54P000376
• When vehicle is driven on the road with
many steep uphills and downhills
• When your vehicle is towing a trailer
EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
Do not use the adaptive cruise con-
trol system under the following situa-
tions. Otherwise, the system will not
function properly and unexpected
accidents may occur.
EXAMPLE

3-34
OPERATING YOUR VEHICLE
54P00-01E
54P000374
• Highway gate
• When the vehicle cannot move in a
straight manner without consistently
steering, due to an accident or break-
down
• When the vehicle is running left turn lane
or right turn lane
• When the radiator grill or front bumper
hit a hard object
• When the system is temporarily stopped
or malfunctioning, some of the following
indicator and messages will come on:
– Adaptive cruise control system warn-
ing light
– “INSPECT CRUISE SYSTEM” mes-
sage
– “RADAR BRAKE SUPPORT: NOT
ACTIVE BY SENSOR.” message
– “RADAR BRAKE SUPPORT SYS
INSPECTION REQUIRED” message
– “RADAR BRAKE SUPPORT FCN
TEMPORARILY DISABLED” message
Situations where radar may not activate properly
Under the following situations, the radar
may not detect a vehicle ahead correctly
and frontal collision warning may not func-
tion. You need to decelerate the vehicle
operating brakes as necessary.
• When a vehicle ahead is running slowly
or stopping at the end of the line in a traf-
fic jam or the tollgate
• When the vehicle is approaching repair-
ing road
• While running inside of tunnel
• When the radar sensor cover is covered
in snow, water or dirt
• When there is bad weather such as
heavy rain or fog, a blizzard or sand-
storm or when the vehicle in front of you
is surrounded by water, snow or sand
• A vehicle ahead has extremely small
rear end area such as an unloaded
trailer
• When your vehicle is weighed down by
heavy items in the luggage compartment
or rear seat
• When your vehicle is running at 160 km/
h (100 mph) or higher speed
• When a vehicle ahead is cutting in sud-
denly
54P000375
• When the bicycles or motorcycles are
running on the edge of your lane
EXAMPLE
WA R N I N G
Always drive safely with proper driv-
ing operations depending on traffic
situation.
EXAMPLE

3-35
OPERATING YOUR VEHICLE
54P00-01E
Situations where radar may activate properly
Under the following situations, the radar
system detects a vehicle on the neighbor-
ing lane or roadside objects and frontal col-
lision warning may function.
• At a corner or narrow traffic lane
• The vehicle position in your lane
is unstable due to steering operation etc.
• Objects protruding from the road’s
surface such as manhole covers and
other metal objects, as well as falling
objects or level changes in the road
Setting cruising speed
Adaptive cruise control switch
54P000346
(1) Following distance setting switch
(2) “CRUISE” switch
(3) “CANCEL” switch
(4) “RES +” switch
(5) “SET –” switchInformation display
54P000347
(6) Distance indicator
(7) Cruise indicator
(8) “SET” indicator
(9) Vehicle ahead detecting indicator
(10) Set speed indication
1) Turn on the adaptive cruise control sys-
tem by pushing “CRUISE” switch
(2).When the cruise indicator (7) and
distance indicator (6) appear on the
information display, you can set cruis-
ing speed.
2) Accelerate or decelerate to the desired
speed.WA R N I N G
Always drive safely with proper driv-
ing operations depending on traffic
situation.
(1)
(2)(3)
(4)
(5)
EXAMPLE(7)
(8) (9)(6)
(10)
EXAMPLE

3-36
OPERATING YOUR VEHICLE
54P00-01E
3) Push “SET –” switch (5), “SET” indica-
tor (8), vehicle ahead detecting indica-
tor (9) and set speed indication (10)
appear on the information display.
Take your foot off the accelerator pedal
and the set speed will be maintained. At
this time, vehicle ahead detecting indi-
cator (9) will vary as follows, depending
on the presence or absence of the vehi-
cle ahead.Changing vehicle distance
While cruise indicator (7) is on, you can
adjust a following distance between your
vehicle and the vehicle ahead as follows,
by pressing following distance setting
switch (1).
Indication Description
A vehicle ahead is not
detected. In this case, the
vehicle is in the state of
constant-speed control.
A vehicle ahead is
detected. In this case, the
vehicle is in the state of
deceleration control and
following control.
WA R N I N G
If the cruising speed is accidentally
set, you could lose control of the
vehicle. This could lead to an acci-
dent, resulting in severe injury or
death.
Turn off the adaptive cruise control
system and check that the cruise
indicator (7) disappears when the
system is not in use.
Long
A following distance will
be kept longer, com-
pared with Middle set-
ting.
Middle
This is an initial set-
ting. When your vehicle
is driven at 80 km/h (50
mph), a following dis-
tance will be kept as
about 40 m (131 ft).
Short
A following distance will
be kept shorter, com-
pared with Middle set-
ting.
WA R N I N G
Maintain a safe following distance
depending on traffic situation. Other-
wise, it could result in severe injury
or death.