maintenance reset SUZUKI GRAND VITARA 2022 Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2022, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2022Pages: 482, PDF Size: 21 MB
Page 93 of 482
2-71
BEFORE DRIVING
54P00-01E
Gearshift indicator
The display (E) shows the gearshift indica-
tor.
54P000232
Refer to “Gearshift indicator” in “OPERAT-
ING YOUR VEHICLE” section.
Trip meter
The display (F) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
Odometer
The display (G) shows the odometer.
The odometer records the total distance
the vehicle has been driven.
Setting mode
When the ignition switch is in “ON” position
or the ignition mode is “ON” and the vehi-
cle is stationary, you can enter the setting
mode of the information display by pushing
and holding the indicator selector knob (2)
for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
61MM0A161
NOTE:
The currently selected setting item is sur-
rounded by a frame.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
Page 121 of 482
2-99
BEFORE DRIVING
54P00-01E
Oil change request light(if equipped)
79JM007
Your vehicle has the oil life monitoring sys-
tem and related oil change request light
that alerts you to change the engine oil and
oil filter.
When this light comes on or blinks, change
engine oil and oil filter immediately.
For details on how to change the engine oil
and oil filter, refer to “Changing engine oil
and filter” in “INSPECTION AND MAINTE-
NANCE” section.
Gasoline engine model and diesel engine
model have different lighting methods for
oil change request light. Check an appro-
priate method from the following descrip-
tions, according to your vehicle model.
(For gasoline engine model)
This light comes on for several seconds
when the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON” so you
can check that light is working.If either of odometer reading or time is
reached to the value which is set by the
system, this light blinks when the ignition
switch or engine switch is in “ON” position.
In addition, the message is shown on the
information display to tell you it is neces-
sary to change the engine oil and oil filter.
When the engine oil and oil filter are
changed, and the oil life monitoring system
is reset, this light will go out.
Whenever the engine oil and oil filter are
changed, the light must be reset to monitor
the next oil change timing properly. The
light will go out after the reset. For the
resetting procedure, refer to “Information
display” in this section.
NOTE:
This light is used to facilitate the oil and oil
filter change according to the maintenance
schedule.(For diesel engine model)
This light comes on for several seconds
when the ignition switch is turned to “ON”
position or the engine switch is pressed to
change the ignition mode to “ON” so you
can check that light is working.
If this light blinks when the engine is run-
ning, you should change the engine oil and
oil filter immediately since the monitoring sys-
tem has calculated that oil life has been
diminished by a deterioration of engine oil.
When the engine oil and oil filter are
changed, and the oil life monitoring system
is reset, this light will go out.
NOTICE
Severe engine damage will result, if
you keep operating the engine after
this light comes on.
Change the engine oil and oil filter
immediately when the light blinks.
Page 360 of 482
7-22
INSPECTION AND MAINTENANCE
54P00-01E
Pull out the oil dipstick, wipe oil off with a
clean cloth, insert the dipstick all the way
into the engine, and then remove it again.
The oil on the stick should be between the
upper and lower limits shown on the stick.
If the oil level indication is near the lower
limit, add enough oil to raise the level to
the upper limit.NOTE:
When the soot particles accumulated in
the DPF
® are combusted, the amount of
the engine oil may increase due to the dilu-
tion with the fuel. This is not a vehicle mal-
function. The soot particles accumulated in
the DPF
® are combusted automatically
during driving. However, they may not be
combusted in the following cases.
• When you drive at low speed for a long
time
• When you repeat a short-time or short-
distance driving
1) When the DPF
® warning light comes
on, drive at a speed of 50 km/h (31
mph) or higher for more than 25 min-
utes to regenerate the DPF
® properly.
For details, refer to “Diesel particulate
filter (DPF
®)” in “OPERATING YOUR
VEHICLE” section.
2) When the oil change request light
blinks, change the engine oil and oil fil-
ter, and reset the oil life monitoring sys-
tem. To reset the oil life monitoring
system, consult your SUZUKI dealer.
3) When the engine oil level exceeds the
MAX level on the dipstick, consult your
SUZUKI dealer.
Refilling
81A147
Remove the oil filler cap and pour oil slowly
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
not to overfill the oil. Too much oil is almost
as bad as too little oil. After refilling, start the
engine and allow it to idle for about a min-
ute. Stop the engine, wait about 5 minutes
and check the oil level again.
NOTICE
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
NOTICE
(For diesel engine model)
Do not top up the oil over the MAX
limit. Too much oil causes serious
engine trouble.
EXAMPLE
Open Close
Page 362 of 482
7-24
INSPECTION AND MAINTENANCE
54P00-01E
5) Reinstall the drain plug and gasket.
Tighten the plug with a wrench to the
specified torque.
NOTE:
• Whenever the engine oil is changed, the
oil life monitoring must be reset to moni-
tor the next oil change timing properly.
To reset the light, consult your SUZUKI
dealer. If you reset it by yourself, refer to
“Setting mode” in “BEFORE DRIVING”
section (for gasoline engine model).
• For more information of the oil change
request light and oil life monitoring, refer
to “Oil change request light (if equipped)”
and “Information display” in “BEFORE
DRIVING” section.
Oil filter replacement
NOTE:
(For diesel engine model)
Since special procedures and tools are
required, ask your authorized SUZUKI
dealer for this job.
1) Using an oil filter wrench, turn the oil fil-
ter counterclockwise and remove it.
2) Using a clean rag, wipe off the mount-
ing surface on the engine where the
new filter will be seated.
3) Smear a small amount of engine oil
around the rubber gasket of the new oil
filter.
4) Screw the new filter by hand until the fil-
ter gasket contacts the mounting sur-
face.(For gasoline engine model)
54G092
(1) Loosen
(2) Tighten
WA R N I N G
(Continued)
To minimize your exposure to used
oil, wear a long-sleeve shirt and
moisture-proof gloves (such as dish-
washing gloves) when changing oil. If
oil contacts your skin, wash thor-
oughly with soap and water.
Launder any clothing or rags if it is
with oil.
Recycle or properly dispose of used
oil and oil filters.
Page 378 of 482
7-40
INSPECTION AND MAINTENANCE
54P00-01E
54P000705
To remove the battery:
1) Disconnect the negative cable (2).
2) Disconnect the positive cable (3).
3) Remove the bracket bolt (4) and
remove the bracket (5).
4) Remove the battery.
To install the battery:
1) Install the battery in the reverse order of
removal.
2) Tighten the bracket bolt and battery
cables securely.
NOTE:
When the battery is disconnected, some of
the vehicle’s functions will be initialized
and/or deactivated.
These functions must be required to reset
after the battery is reconnected.(Battery label)
54P000733
(6) Crossed-out wheeled bin symbol
(7) Chemical symbol of “Pb”The crossed-out wheeled bin symbol (5)
located on the battery label indicates that
the used battery should be collected sepa-
rately from ordinary household trash.
The chemical symbol of “Pb” (6) indicates
the battery contains more than 0.004%
lead.
By ensuring the used battery is disposed
of or recycled correctly, you will help pre-
vent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropri-
ate trash handling of the battery. The recy-
cling of materials will help to conserve
natural resources. For more detailed infor-
mation about disposing of or recycling the
used battery, consult your SUZUKI dealer.
(2)
(3)
(4)(5)EXAMPLEWA R N I N G
Batteries contain toxic substances
including sulfuric acid and lead. They
could have potential negative conse-
quences for the environment and
human health. Used batteries must
be disposed of or recycled according
to applicable rules or regulations and
must not be disposed of with ordi-
nary household trash. Make sure not
to tip over the battery when you
remove it from the vehicle. Other-
wise, sulfuric acid could run out and
you might get injury.
Pb
(6)
(7)