oil level SUZUKI IGNIS 2021 User Guide

7-16
INSPECTION AND MAINTENANCE
75RM4-01E
Interval: This interval should be judged byodometer reading or months, whichever
comes first. km (x1000) 20 40 60 80 100 120
miles (x1000) 12.5 25 37.5 50 62.5 75 months 12 24 36 48 60 72EMISSION CONTROL SYSTEM*4-1. PCV valve ––– I ––*4-2.
Fuel evaporative emission control system
–
–
–
–
–
I
BRAKE
*5-1.
Brake discs and pads (front)
I
I
I
I
I
I
Brake drums and shoes (rear) –I–I–I
*5-2.
Brake hoses and pipes
–
I
–
I
–
I
5-3. Brake fluid Check, *Replacement – R – R – R
5-4.
Brake lever and cable
Check, *Adjustment (1st 20000 km only)
I
–
–
–
–
–
CHASSIS AND BODY
*6-1.
Clutch (Cable control type)
I
I
I
I
I
I
6-2. Tires/Wheels IIIIII
*6-3.
Wheel bearings
–
I
–
I
–
I
*6-4. Drive axle boots/Propeller shafts (4WD) –I–I–I
*6-5.
Suspension system
–
I
–
I
–
I
*6-6. Steering system –I–I–I
*6-7.
Manual transaxle oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 40000 km (25000 miles) or 24 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
*6-8.
Auto Gear Shift oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 40000 km (25000 miles) or 24 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
6-9.
Continuously variable transaxle (CVT)
Fluid level
–
I
–
I
–
I
*6-10. Transfer oil (4WD) Inspect every 40000 km (25000 miles) or 24 months.
Replace every 160000 km (100000 miles) or 96 months.
*6-11. Rear differential oil (4WD) Inspect every 40000 km (25000 miles) or 24 months.
Replace every 160000 km (100000 miles) or 96 months.
6-12. All latches, hinges and locks –I–I–I*6-13.
Air conditioner filter element (if equipped)
–
I
R
–
I
R
WA R N I N G
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid
storing them near a heater or heating device. When scrapping th e absorber, the gas must be released from the absorber
safely. Ask your deal er for assistance.

7-17INSPECTION AND MAINTENANCE
75RM4-01E
NOTE:
4WD: 4-wheel driveInterval: This interval should be judged byodometer reading or months, whichever
comes first. km (x1000) 140 160 180 200 220 240
miles (x1000) 87.5 100 112.5 125 137.5 150 months 84 96 108 120 132 144EMISSION CONTROL SYSTEM*4-1. PCV valve –I–––I*4-2.
Fuel evaporative emission control system
–
–
–
–
–
I
BRAKE
*5-1.
Brake discs and pads (front)
I
I
I
I
I
I
Brake drums and shoes (rear) –I–I–I
*5-2.
Brake hoses and pipes
–
I
–
I
–
I
5-3. Brake fluid Check, *Replacement – R – R – R
5-4.
Brake lever and cable
Check, *Adjustment (1st 20000 km only)
–
–
–
–
–
–
CHASSIS AND BODY
*6-1.
Clutch (Cable control type)
I
I
I
I
I
I
6-2. Tires/Wheels IIIIII
*6-3.
Wheel bearings
–
I
–
I
–
I
*6-4. Drive axle boots/Propeller shafts (4WD) –I–I–I
*6-5.
Suspension system
–
I
–
I
–
I
*6-6. Steering system –I–I–I
*6-7.
Manual transaxle oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 40000 km (25000 miles) or 24 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
*6-8.
Auto Gear Shift oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 40000 km (25000 miles) or 24 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
6-9.
Continuously variable transaxle (CVT)
Fluid level
–
I
–
I
–
I
*6-10. Transfer oil (4WD) Inspect every 40000 km (25000 miles) or 24 months.
Replace every 160000 km (100000 miles) or 96 months.
*6-11. Rear differential oil (4WD) Inspect every 40000 km (25000 miles) or 24 months.
Replace every 160000 km (100000 miles) or 96 months.
6-12. All latches, hinges and locks –I–I–I*6-13.
Air conditioner filter element (if equipped)
–
I
R
–
I
R

7-21INSPECTION AND MAINTENANCE
75RM4-01E
Interval: This interval should be judged byodometer reading or months, whichever
comes first. km (x1000) 10 20 30 40 50 60
miles (x1000) 6.25 12.5 18.75 25 31.25 37.5 months6 1218243036BRAKE*5-1. Brake discs and pads (front) –I–I–I
Brake drums and shoes (rear)
–
–
–
I
–
–
*5-2. Brake hoses and pipes ––– I ––
5-3.
Brake fluid
Check, *Replacement
–
–
–
R
–
–
5-4. Brake lever and cable
Check, *Adjustment (1st 20000 km only)
– I ––––
CHASSIS AND BODY *6-1. Clutch (Cable control type) –I–I–I6-2.
Tires/Wheels
–
I
–
I
–
I
*6-3. Wheel bearings –I–I–I
*6-4.
Drive axle boots/Propeller shafts (4WD)
–
–
–
I
–
–
*6-5. Suspension system ––– I ––
*6-6.
Steering system
–
–
–
I
–
–
*6-7.
Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W”
Inspect every 20000 km (12500 miles) or 12 months.Replace every 80000 km (50000 miles) or 48 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
*6-8.
Auto Gear Shift oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 20000 km (12500 miles) or 12 months.Replace every 80000 km (50000 miles) or 48 months.
Other than “SUZUKI GEAR OIL 75W”
–
R
–
R
–
R
6-9. Continuously variable transaxle (CVT) Fluid level – I – I – I
*Fluid deterioration check*
2
–
I
–
I
–
I
*Fluid change Replace every 70000 km (43750 miles).
*6-10.
Transfer oil (4WD)
Inspect every 20000 km (12500 miles) or 12 months.
Replace every 80000 km (50000 miles) or 48 months.
*6-11.
Rear differential oil (4WD)
Inspect every 20000 km (12500 miles) or 12 months.
Replace every 80000 km (50000 miles) or 48 months.
6-12.
All latches, hinges and locks
–
–
–
I
–
–
*6-13. Air conditioner filter element (if equipped)*
3
–I–I–R
WA R N I N G
The shock absorbers are filled with high pressure gas. Never at tempt to disassemble them or throw them into a fire. Avoid
storing them near a heater or heating device. When scrapping th e absorber, the gas must be released from the absorber
safely. Ask your deal er for assistance.

7-22
INSPECTION AND MAINTENANCE
75RM4-01E
NOTE:
4WD: 4-wheel drive
NOTE:
This table shows the service schedule up to 120000 km (75000 miles).
Beyond 120000 km (75000 miles), perform the same services at the same intervals shown in the chart.
*1 Inspect more frequently if the v ehicle is used under dusty conditions.
*2 Check or replace as necessary if you usually drive with high speed or high engine revolutions.
*3 Clean more frequently if the air flow from the air conditioner decreases.Interval: This interval should be judged by odometer reading or months, whichever
comes first. km (x1000) 70 80 90 100 110 120
miles (x1000) 43.75 50 56.25 62.5 68.75 75 months 42 48 54 60 66 72BRAKE*5-1. Brake discs and pads (front) –I–I–I
Brake drums and shoes (rear)
–
I
–
–
–
I
*5-2. Brake hoses and pipes –I–––I
5-3.
Brake fluid
Check, *Replacement
–
R
–
–
–
R
5-4. Brake lever and cable
Check, *Adjustment (1st 20000 km only)
––––––
CHASSIS AND BODY *6-1. Clutch (Cable control type) –I–I–I6-2.
Tires/Wheels
–
I
–
I
–
I
*6-3. Wheel bearings –I–I–I
*6-4.
Drive axle boots/Propeller shafts (4WD)
–
I
–
–
–
I
*6-5. Suspension system –I–––I
*6-6.
Steering system
–
I
–
–
–
I
*6-7.
Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W”
Inspect every 20000 km (12500 miles) or 12 months.Replace every 80000 km (50000 miles) or 48 months.
Other than “SUZUKI GEAR OIL 75W”
–R–R–R
*6-8.
Auto Gear Shift oil
Genuine “SUZUKI GEAR OIL 75W”
Inspect every 20000 km (12500 miles) or 12 months.Replace every 80000 km (50000 miles) or 48 months.
Other than “SUZUKI GEAR OIL 75W”
–
R
–
R
–
R
6-9. Continuously variable transaxle (CVT) Fluid level – I – I – I
*Fluid deterioration check*
2
–
I
–
I
–
I
*Fluid change Replace every 70000 km (43750 miles).
*6-10.
Transfer oil (4WD)
Inspect every 20000 km (12500 miles) or 12 months.
Replace every 80000 km (50000 miles) or 48 months.
*6-11.
Rear differential oil (4WD)
Inspect every 20000 km (12500 miles) or 12 months.
Replace every 80000 km (50000 miles) or 48 months.
6-12.
All latches, hinges and locks
–
I
–
–
–
I
*6-13. Air conditioner filter element (if equipped)*
3
–I–I–R

7-24
INSPECTION AND MAINTENANCE
75RM4-01E
NOTE:
(For EU countries)
The replacement timing varies with the
type of engine oil that you choose.
Refer to “Maintenance schedule” in this
section for corresponding maintenance
schedule.
SAE 0W-16 (1) is the best choice for good
fuel economy and good starting in cold
weather.
NOTE:
We recommend that you use SUZUKI gen-
uine oil. To purchase it, see your SUZUKI
dealer. K12M engine models
71LST0701
(1) Preferred
Be sure that the engine oil you use comes
under the quality classification of SG, SH,
SJ, SL, SM or SN. Select the appropriate
oil viscosity according to the above chart.
SAE 0W-20 (1) is the best choice for good
fuel economy, and good starting in cold
weather.
Oil level check
80G064
52D084
EXAMPLE
UpperLower

7-25INSPECTION AND MAINTENANCE
75RM4-01E
It is important to keep the engine oil at the
correct level for proper lubrication of your
vehicle’s engine. Check the oil level with
the vehicle on a level surface. The oil level
indication may be inaccurate if the vehicle
is on a slope. The oil level should be
checked either before starting the engine
or at least 5 minutes after stopping the
engine.
The handle of the engine oil dipstick is col-
ored with yellow for ea sy identification.
Pull out the oil dipstick, wipe oil off with a
clean cloth, insert the dipstick all the way
into the engine, and then remove it again.
The oil on the stick should be between the
upper and lower limits shown on the stick.
If the oil level indication is near the lower
limit, add enough oil to raise the level to
the upper limit.
Refilling
81A147
Remove the oil filler cap and pour oil slowly
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
not to overfill the oil. Too much oil is almost
as bad as too little oil. A fter refilling, start the
engine and allow it to idle for about a min-
ute. Stop the engine, wait about 5 minutes
and check the oil level again.
Changing engine oil and filterDrain the engine oil while the engine is still
warm.
56KN054
1) Remove the oil filler cap.
2) Place a drain pan under the drain plug.
3) Using a wrench, remove the drain plug and drain the engine oil.
NOTICE
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
EXAMPLEOpen Close
CAUTION
The engine oil temperature may be
high enough to burn your fingers
when the drain plug is loosened. Wait
until the drain plug is cool enough to
touch with your bare hands.EXAMPLE
Open Close

7-27INSPECTION AND MAINTENANCE
75RM4-01E
Tightening (viewed from filter top)
54G093
(1) Oil filter
(2) 3/4 turn5) Tighten the filter as specified below
from the point of contact with the
mounting surface (or to the specified
torque) using an oil filter wrench.
Tightening torque for oil filter:
3/4 turn or
14 Nm (1.4 kg -m, 10.3 lb-ft)
Refill with oil and oil leakage check1) Pour oil through the filler hole and
install the filler cap.
For the approximate capacity of the oil,
refer to “Capacities” in the “SPECIFI-
CATIONS” section.
2) Start the engine and carefully check the oil filter and the drain plug for leakage.
Run the engine at various speeds for at
least 5 minutes.
3) Stop the engine and wait about 5 min- utes. Check the oil level again and add
oil if necessary. Check for leakage
again.
NOTICE
To tighten the oil filter properly, it is
important to accurately identify the
position at which the filter gasket
first contacts the mounting surface.
NOTICE
To prevent oil leakage, check that the
oil filter is tight, but do not over-
tighten it.
NOTICE
• When replacing the oil filter, it is recommended that you use a genu-
ine SUZUKI replacement filter. If
you use an aftermarket filter, check
that it is of equi valent quality and
follow the manufacturer’s instruc-
tions.
• Oil leakage from the periphery of the oil filter or drain plug indicate
incorrect installation or gasket
damage. If you find any leakage or
are not sure that the filter has been
properly tightened, have the vehi-
cle inspected by your SUZUKI
dealer.

7-28
INSPECTION AND MAINTENANCE
75RM4-01E
Engine coolantSelection of coolantTo maintain optimum performance and
durability of your engine, use SUZUKI gen-
uine coolant or equivalent.
NOTE:
If you use the engine coolant other than
the SUZUKI LLC: Super (Blue) for replace-
ment, follow the schedule of SUZUKI LLC:
Standard (Green). To see the detail of the
maintenance schedule, refer to “Periodic
maintenance schedule” in this section.
This type of coolant is the best for cooling
system for the following reasons:
• The coolant helps maintain properengine temperature.
• It gives proper protection against freez- ing and boiling.
• It gives proper protection against corro- sion and rust. Failure to use the proper coolant can dam-
age your cooling system. Your authorized
SUZUKI dealer can help you select the
proper coolant.
Coolant level checkCheck the coolant le
vel at the reservoir
tank, not at the radiator. With the engine
cool, the coolant level should be between
“FULL” and “LOW” marks.Adding coolant
NOTICE
SUZUKI LLC: Super (Blue) coolant;
This coolant is already diluted to the
proper percentage. Do not dilute with
distilled water additionally. Doing so
may result in the possibility of freez-
ing and/or overheating coolant.
NOTICE
To avoid damaging your cooling sys-
tem:
• Always use a high quality ethylene
glycol base non-silicate type cool-
ant diluted with distilled water at
the correct mixture concentration.
• Check that the proper mix is 50/50
coolant to distill ed water and in no
case higher than 70/30. Concentra-
tions greater than 70/30 coolant to
distilled water will cause overheat-
ing conditions.
• Do not use straight coolant nor plain water (except SUZUKI LLC:
Super (Blue)).
• Do not add extra inhibitors or addi- tives. They may not be compatible
with your cooling system.
• Do not mix different types of base coolants. Doing so may result in
accelerated seal wear and/or the
possibility of severe overheating
and extensive engine or CVT (if
equipped) damage.
WA R N I N G
Swallowing engine coolant can cause
severe injury or death. Inhaling cool-
ant mist or vapors or getting coolant
in your eyes could result in severe
injury.
• Do not drink antifreeze or coolantsolution. If swallowed, do not
induce vomiting. Immediately con-
tact a poison control center or a
physician.
• Avoid inhaling coolant mist or hot
vapors. If inhaled, remove to a
fresh air area.
• If coolant gets in the eyes, flush
with water and seek medical atten-
tion.
• Wash thoroughly after handling
coolant.
• Keep engine coolant out of the
reach of children and pets.

7-33INSPECTION AND MAINTENANCE
75RM4-01E
75F086
81PN159 75RM370
(1) FULL
(2) LOW
(3) The lowest point = Fluid level
5) The handle of the CVT fluid dipstick is colored orange for ea sy identification.
Remove the dipstick, clean it and push
it back in until the cap seats. Then pull
out the dipstick.
6) Check both sides of the dipstick, and read the lowest level. The fluid level
should be between the two marks on
the dipstick.
Deterioration checking or changing oilSince special procedures, materials and
tools are required to check the deteriora-
tion of CVT oil or change, it is recom-
mended that you trust this job to your
authorized SUZUKI dealer.
EXAMPLE
EXAMPLE
NOTICE
After checking or adding oil, be sure
to insert the di pstick securely.
(3)
(1)
(2)
C
H
(ΟΝ03/(

7-34
INSPECTION AND MAINTENANCE
75RM4-01E
Gear oilManual transaxle oil / Auto Gear
Shift oil / transfer oil (4WD) / rear differential oil (4WD)When adding gear oil, use gear oil with the
appropriate viscosity and grade as shown
in the chart below.
We highly recommend you use “SUZUKI
GEAR OIL 75W” for manual transaxle or
Auto Gear Shift oil.Manual transaxle oil
Auto Gear Shift oil
54P120706
We highly recommend you use “SUZUKI
GEAR OIL 75W-85” for transfer oil (4WD)
and rear differential oil (4WD).Transfer oil (4WD)
Rear differential oil (4WD)
71LMT0701
Gear oil level checkManual transaxle / Auto Gear Shift
68KH073
(1) Oil filler and level plug
C
Fo
o-30
-22
-20
-4 -10
14 32 50 68 86 104 010203040
75W
C
Fo
o-30
-22
-20
-4 -10
14 32 50 68 86 104 010203040
75W-85
(1)
EXAMPLE