spare wheel SUZUKI JIMNY 2018 User Guide

INS.PECTION AND MAINTENANCE
4-tyre rotation
65D459
To avoid uneven wear of your tyres and to prolong their life, rotate the tyres as illus­trated. Tyres should be rotated every 10000 km (6000 miles). After rotation, adjust front and rear tyre pressures to the specification listed on your vehicle's Tyre Information Label.
6-39
Changing Wheels
78RB07014
To change a wheel, use the following pro­cedure:
1) Remove the jack, tools and spare wheel from the vehicle.
NOTE: How to remove the spare wheel:
78RB07052
1. Remove the center nut (1 ), then remove the spare wheel half cover (2) (if equipped). 2. Remove the wheel nuts of the spare wheel, then remove the spare wheel with both hands.
2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in the "EMERGENCY SER­VICE" section in this manual) 4) Remove the wheel nuts and wheel. 5) Before installing the new wheel, clean any mud or dirt off from the surface of the wheel and hub with a clean cloth. Clean the hub carefully; it may be hot from driving.

6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB07017
Tightening torque for wheel nut: 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts in a crisscross fashion with a wrench as shown in the illustration.
A WARNING
Use genuine wheel nuts and tighten them to the specified torque as soon as possible after changing wheels. Incorrect wheel nuts or improperly tightened wheel nuts may come loose or fall off, which can result in an accident. If you do not have a torque wrench, have the wheel nut torque checked by a SUZUKI dealer.
INSPECTION AND MAINTENANCE
NOTE: How to install the spare wheel:
(3)
78RB07053
When you install a 195/B0R 15 spare wheel to the vehicle, set the spare tyre bracket (3) (if equipped) with the mark of "195" on up posi­tion, and handle it in the reverse order of removal. For vehicles equipped with the spare wheel half cover; when you install the spare wheel half cover, check that the hollow (4) of the cover is positioned below the center of the spare wheel half cover.
6-40

EMERGENCY SERVICE
Tyre changing tool
0
57
(3) (1) (2)
78RB08001
(1) Jack (2) Jack handle (3) Wheel wrench
The tyre changing tools are stowed in the luggage compartment. Refer to "LUGGAGE COMPARTMENT" in "ILLUSTRATED TABLE OF CONTENTS" section.
7-1
Jacking instructions
75F062
1) Place the vehicle on level, hard ground. 2) Set the parking brake firmly and shift into "P" (Park) if your vehicle has an automatic transmission, or shift int6 "R" (Reverse) if your vehicle has a manual transmission.
A WARNING
Shift into "P" (Park) for an automatic transmission, or into "R" (Reverse) for a manual transmission vehicle when you jack up the vehicle. • Never jack up the vehicle with the transmission in 11N" (Neutral). Oth­erwise, unstable jack may cause an accident.
3) Turn on the hazard warning switch if your vehicle is near traffic. 4) Block the front and rear of the wheel diagonally opposite of the wheel being lifted. 5) Place the spare wheel near the wheel being lifted as shown in the illustration in case that the jack is slipped.

NOTICE
Never apply a garage jack to the exhaust pipe, front fender splash guard, side sill splash, rear fender splash guard, front differential or rear differential.
NOTE: For more details, contact a SUZUKI dealer.
Changing wheels
To change a wheel, use the following pro­
cedure: 1) Prepare the jack, tools and spare tyre. 2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in this section).
A WARNING
Shift into "P" (Park) for an automatic transmission, or into 11R" (Reverse) for a manual transmission vehicle when you jack up the vehicle. Never jack up the vehicle with the transmission in "N" (Neutral). OthR erwise, unstable jack may cause an accident.
4) Remove the wheel nuts and wheel.
65J4033
5) Clean any mud or dirt off from the sur­face of the wheel (1 ), hub (2), thread part (3) and surface of the wheel nuts (4) with a clean cloth. Clean the hub carefully; it may be hot from driving.
EMERGENCY SERVICE
6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB08003
Tightening torque for wheel nut 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts with a wheel wrench in numerical order as shown in the illustration.
7-4

SPECIFICATION
Specifications
NOTE: Specifications are subject to change without notice.
MIT: Manual transmission NT: Automatic transmission
ITEM: Dimensions UNIT: mm (in.)
Overall length 3625 (142.7) (Front bumper to spare tyre) 3645 (143.5) (Front bumper to spare wheel half cover)
Overall width 1645 (64.8)
Overall height 1720 (67.7)
Wheelbase 2250 (88.6)
Track I Front 1395 (54.9)
I Rear 1405 (55.3)
Ground clearance 210 (8.2)
9-3

No.Using Conditions • When temperature under -40-C . • On miring or sand ground . • On big gradient road . • In extreme nature condition: rainstorm, typhoon, cyclone, snowstorm, thunder•storm. etc . • Loading dangerous heavy, for instance: melted metal. acidity substance, radioactivity substance or specially crisp goods • • Contact with hood directly . • Using on boat. • The ground with difference in level.
Operation Instructions Whenever a wheel is changed, always remove any corrosion that may be present on inside of wheel and wheel mounting surface on vehicle. Details: Please operate according to the "operation instructions", Operate the jack on the level ground while checking the jack and the load. Musln"I operate under raising load, unless the load is fastened surely . • Park the car on the nat, love ground and apply the brake firmly. • Set transmission in "reverse"(automalic transmission in ·park") . • Turn on the hazard warning Hasher . • Remove jacklng tools and spare tire from stowage area . • Block fFont and rear of wheel diagonally opposlte wheel being removed before operating jack .
~
ITT
~ .s,.Cl(Jf>Of'(llITT J-'CKIW ~ • Loosen, but do not remove wheel nuts by turning wrench counter clockwise • • Raise jack until Jack-head groove fits boss or frame see Illustrations . • Operate jack with slow, smooth motion, using Jack handle . • Raise vehicle so an innated lire will just clear surface, remove nuts and wheel. • Install wheel, then slightly tighten each nut, wheel must be seated on hub . • lower vehicle, and fully tighten wheel nuts In across-cross sequence by turning wrench clockwise.
Maintenance • Please prevent the JACK SCREW from accretion of dirt . • Check the nameplate, keep the shape same as original. • No-re jigger the Jack's construction privately . • After any use, consult immediately your Suzuki Dealer or Service Partner for inspection and maintenance of the jack . • If the label (slicker) is damaged, pt ease consult your Suzuki Dealer or Service Partner.