steering SUZUKI NEXA 2015 1.G User Guide
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 111 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K . H \ O H V V 3 X V K 6 W D U W
6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS169
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
82K254
3) The “PUSH START SWITCH” message
will appear on the information display in
the instrument cluster. Push the engine
switch (1). When the engine is started,
the starter motor will automatically stop.
NOTE:
• You do not need to keep the engine
switch pressed to start the engine.
• The engine of a manual transaxle vehi-
cle will not start unless the clutch pedal
is depressed.
• During the engine starting procedure,
messages on the information display will
help you. Refer to “Information Display”in the “BEFORE DRIVING” section for
details.
• You should turn off such loads as the
headlights and air conditioning system to
facilitate starting of the engine.
• Even if you fail to start the engine, the
starter motor will stop operating auto-
matically after a short time. After the
starter motor has stopped or if there is
some problem with the system, the
starter motor will rotate only while the
engine switch is being pressed.
6 W R S S L Q J W K H H Q J L Q H• Depress the engine switch to stop the
engine after the vehicle stopped com-
pletely.
• In case of emergency, you can stop the
engine by quickly pushing the engine
switch more than 3 times, or pushing
and holding the engine switch more than
2 seconds while the vehicle in motion.
NOTE:
Except in emergency, do not stop the
engine while the vehicle in motion.
The steering and braking operation will
require more efforts when the engine
stopped.
Refer to “Braking” in this section.
• If the engine has been stopped and
stayed as it as for while after the engine
was stopped unexpectedly or was raced
before stopped, a clicking sound may be
heard from around the engine when
engine restarted. This is not a malfunc-
(1)
: $ 5 1 , 1 *
0 D N H V X U H W K D W W K H S D U N L Q J E U D N H L V
V H W I X O O \ D Q G W K H W U D Q V D [ O H L V L Q 1 H X
W U D O E H I R U H D W W H P S W L Q J W R V W D U W W K H
H Q J L Q H
NOTICE
Page 115 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
& U X L V H & R Q W U R O L I H T X L S S H G The cruise control system allows you to
maintain a steady speed without keeping
your foot on the accelerator pedal. The
controls for operating the cruise control
system are on the steering wheel.
You can use the cruise control system with
the following conditions:
• The gear position is in 3rd, 4th, 5th or 6th
(if equipped).
• The vehicle speed is about 40 km/h (25
mph) or higher.
61MS416
(1) “CRUISE” switch
(2) “CANCEL” switch
(3) “RES +” switch
(4) “SET –” switch
7 R 6 H W & U X L V L Q J 6 S H H G1) Turn on the cruise control system by
pushing the “CRUISE” switch (1). When
the “CRUISE” indicator light comes on,
you can set cruising speed.
2) Accelerate or decelerate to the desired
speed.
3) Push the “SET –” switch (4) and the
“SET” indicator light will turn on. Take
your foot off the accelerator pedal and
the set speed will be maintained.
: $ 5 1 , 1 *
7 R K H O S D Y R L G O R V V R I Y H K L F O H F R Q W U R O
G R Q R W X V H W K H F U X L V H F R Q W U R O V \ V W H P
Z K H Q G U L Y L Q J L Q K H D Y \ W U D I I L F R Q V O L S
S H U \ R U Z L Q G L Q J U R D G V R U R Q V W H H S
G R Z Q J U D G H V
(1)(2)
(3)(4)
: $ 5 1 , 1 *
, I W K H F U X L V L Q J V S H H G L V V H W E \ D F F L
G H Q W \ R X F D Q Q R W G H F H O H U D W H D Q G P D \
O R R V H F R Q W U R O R I W K H Y H K L F O H 7 K L V
F R X O G O H D G W R D Q D F F L G H Q W U H V X O W L Q J L Q
V H Y H U H L Q M X U \ R U G H D W K
7 X U Q R I I W K H F U X L V H F R Q W U R O V \ V W H P
D Q G P D N H V X U H W K H
Page 117 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
& D Q F H O O D W L R Q R I W K H & U X L V H & R Q W U R OThe “SET” indicator light will go off and the
cruise control will be canceled temporarily
with following procedures:
• Push the “CANCEL” switch (2).
• Depress the brake pedal.
• Depress the clutch pedal.
• The vehicle speed falls more than about
20 percent from the set speed.
• Any time the vehicle speed falls below
40 km/h (25 mph).
To resume the previously set speed, push
the “RES +” switch (3) and turn on the
“SET” indicator light. Besides, the vehicle
speed has to be above 40 km/h (25 mph)
when the vehicle is not in the above condi-
tions.
To turn off the cruise control system, push
the “CRUISE” switch (1) and make sure
the “CRUISE” indicator light is off.
Also, if the malfunction indicator light in the
instrument cluster comes on or blinks, the
cruise control system will be turned off.
NOTE:
If you turn off the cruise control system, the
previously set speed in the memory is
cleared. Reset your cruising speed again.
3 D U N L Q J 6 H Q V R U V L I H T X L S S H G
61MM0A192
(1) Symbol representing an obstacle
detected by parking sensor*
* This symbol represents an obstacle
that is located to the right rear at
the vehicle.
• The parking sensor system uses ultra-
sonic sensors to detect obstacles near
the rear bumper. If obstacles are sensed
while you are parking or moving the
vehicle slowly, the system warns you by
sounding a buzzer and displaying sym-
bols representing the obstacles on the
information display in the instrument
cluster.
• The system emits an ultrasonic wave
and the relevant sensor detects the
return of the wave reflected by an obsta-
cle. The system measures the time
taken by the ultrasonic wave to reach the
obstacle and return from it, from which it
determines the obstacle’s position.
• The parking sensor function can be used
when you press the engine switch tochange the ignition mode to “ON”, the
gearshift lever is in “R” position and the
parking sensor switch is in the “ON”
position. This function is helpful in the
following cases: pulling over to the curb;
parallel-parking the vehicle; steering the
vehicle into a garage; driving along an
alley; and moving slowly in a place with
obstacles.
(1)
: $ 5 1 , 1 *
Page 127 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
% U D N H $ V V L V W 6 \ V W H P L I H T X L S S H G When you slam the brakes on, the brake
assist system judges as an emergency
stop and provides more powerful braking
for a driver who cannot hold down the
brake pedal firmly.
NOTE:
If you quickly and forcefully depress the
brakes, you may hear a clicking sound in
the brake pedal. This is normal and indi-
cates that the brake assist system is acti-
vated properly. $ Q W L / R F N % U D N H 6 \ V W H P $ % 6
L I H T X L S S H G ABS will help in avoiding locking of the
wheel by electronically controlling braking
pressure. It will also help you maintain
steering control when braking on slippery
surfaces or when braking hard”
The ABS works automatically, so you do
not need any special braking technique.
Just push the brake pedal down without
pumping. The ABS will operate whenever
it senses that the wheels are locking up.
You may feel the brake pedal moves a little
while the ABS is operating.
NOTE:
The ABS will not work if vehicle speed is
under about 10 km/h (6 mph).
63J081
(1) ABS warning light
(2) Brake system warning light
: $ 5 1 , 1 *
Page 132 of 288
Downloaded from www.Manualslib.com manuals search engine ' 5 , 9 , 1 * 7 , 3 6
0 6 (
pressure shown on the label on the driver’s
side door or the driver’s door lock pillar. + L J K Z D \ ' U L Y L Q JWhen driving at highway speeds, pay
attention to the following:
• Stopping distance progressively
increases with vehicle speed. Apply the
brakes far enough ahead of the stopping
point to allow for the extra stopping dis-
tance.
• On rainy days, hydroplaning can occur.
Hydroplaning is the loss of direct contact
between the road surface and the vehi-
cle’s tires due to a water film forming
between them. Steering or braking the
vehicle while hydroplaning can be very
difficult, and loss of control can occur.
Keep speed down when the road sur-
face is wet.
• At high speeds, the vehicle may be
affected by side winds. Therefore,
reduce speed and be prepared for unex-
pected buffeting, which can occur at the
exits of tunnels, when passing by a cut
of a hill, or when being overtaken by
large vehicles, etc.
' U L Y L Q J R Q + L O O V
64MS171
• When climbing steep hills, the vehicle
may begin to slow down and show a lack
of power. If this happens, you should
shift to a lower gear so that the engine
will again be operating in its normal
power range. Shift rapidly to prevent the
vehicle from losing momentum.
• When driving down a hill, the engine
should be used for braking by shifting to
next lower gear.
: $ 5 1 , 1 *
7 U \ Q R W W R K R O G W K H E U D N H S H G D O G R Z Q
W R R O R Q J R U W R R R I W H Q Z K L O H J R L Q J
G R Z Q D V W H H S R U O R Q J K L O O 7 K L V F R X O G
F D X V H W K H E U D N H V W R R Y H U K H D W U H V X O W
L Q J L Q U H G X F H G E U D N L Q J H I I L F L H Q F \
) D L O X U H W R W D N H W K L V S U H F D X W L R Q F R X O G
U H V X O W L Q O R V V R I Y H K L F O H F R Q W U R O
NOTICE
: K H Q G H V F H Q G L Q J D G R Z Q K L O O
1 ( 9 ( 5 W X U Q W K H L J Q L W L R Q N H \ W R W K H
Page 133 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' U L Y L Q J R Q 6 O L S S H U \ 5 R D G V
60G089A
Under wet road conditions you should
drive at a lower speed than on dry roads
due to possible slippage of tires during
braking. When driving on icy, snow-cov-
ered, or muddy roads, reduce your speed
and avoid sudden acceleration, abrupt
braking, or sharp steering movements.
7 L U H & K D L Q VTire chains should only be used if they are
needed to increase traction or are required
by law. Make sure that the chains you use
are the correct size for your vehicle’s tires.
Also make sure that there is enough clear-
ance between the fenders and the chains
as installed on the tires.
Install the chains on the front tires tightly,
according to the chain manufacturer’s
instructions. Retighten the chains after
driving about 1.0 km (1/2 mile) if neces-
sary. With the chains installed, drive slowly.
, I < R X U 9 H K L F O H * H W V 6 W X F NIf your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between first gear and reverse. This will
create a rocking motion which may give
you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting.
Do not race the engine. Excessive
wheel spin will cause the tires to dig
deeper, making it more difficult to free
the vehicle.
2)
If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S or a roadside assistance
service. If a towing service is not
available in an emergency, your
vehicle may be tem-porarily towed by
a towing cable or chain secured to
the towing hook either on the front of
the vehicle or on the rear of the vehicle.
Refer to “Frame Hooks” in the
“OTHER CONTROLS AND
EQUIPMENT” section.
NOTICE
Page 137 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
when the windshield glass is dry or the
wiper blade and glass may get dam-
aged.
72F-08-021
72F-08-022
0 D U J L Q ) R U 6 D I H W \It is important to allow yourself a margin for
safety during driving so that you can cope
with erroneous or unexpected driving of other
drivers. For that, observe the following.•Drive at a safe speed.
•Maintain a sufficient distance between
your vehicle and the vehicle ahead.
• Don’t force yourself to overtake other
vehicles.
• Don’t make quick start, hard steering or
sudden stops.
• Allow an ample time in the driving
schedule.
• Observe traffic rules and regulations. & R Q F O X V L R QA perfect driver does not exist. The
endeavour of every motorist should be to
strive for perfection. Safety consciousness
not only ensures your safety and the safety
of other road users, it also helps reduce
the wear and tear on your vehicle, prolongs
its life, gives more mileage and ensures a
comfortable driving experience.
) R O O R Z W K H G R
Page 169 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
• To return the blower speed selector (2),
air intake selector (3), and “MODE”
switch (4) to automatic operation, push
the “AUTO” switch (8).
64MS149
Be careful not to cover the interior tem-
perature sensor (10) located between the
steering wheel and the climate control
panel, or the solar sensor (11) located at
the top of the central part of the dash-
board. These sensors are used by the
automatic system to regulate temperature.
0 D Q X D O R S H U D W L R Q
You can manually control the climate con-
trol system. Set the selectors to the
desired positions.
64MS091
NOTE:
If you need maximum defrosting:
• push the defrost switch (5) to turn on the
defroster (the air conditioning system will
come on and the fresh air position (b)
will be selected automatically),
• set the blower speed selector to HIGH,
• adjust the temperature selector to the
“HI” indication on the display, and
• adjust the side outlets so the air blows
on the side windows.
0 D L Q W H Q D Q F HIf you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
If your air conditioner is equipped with air
filters, clean or replace them as specified
in the “Maintenance Schedule” in the
Page 205 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
' H O H W L R Q R I D X G L R G H Y L F H L Q I R U P D W L R Q
' H O H W H $ X G L R
Follow the instructions below to delete the
registered information of audio device.
1) Press the Bluetooth
® setup button (6).
The Bluetooth
® setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “List Audio”,
and press the knob (2) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select an audio
device to be deleted, and press the
knob (2) to determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete”, and
press the knob (2) to determine the
selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete?”,
and press the knob (2) to determine the
selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Confirm”,
and press the knob (2) to complete the
deletion.
NOTE:
When selecting “Go Back”, the previous
menu will be displayed.
' L V F O D L P H U I R U % O X H W R R W K
Š I X Q F W L R Q
• Depending on the mobile phone models,
some phones may not be compatible
fully or partially (some function may be
restricted).
• Connectivity or voice quality may get
affected depending on circumstances.
• After the ignition switch is turned to the
“ON” position, the audio system takes
few seconds to detect and connect to
the Bluetooth
® device (if already paired)
• Make sure that you are aware of all
applicable lock laws and accordingly use
Bluetooth
Š device.
5 H P R W H $ X G L R & R Q W U R O V
L I H T X L S S H G Controlling of basic functions of the audio
system is available using the switches on
the steering wheel. $ G M X V W L Q J W K H Y R O X P H
• To increase the volume, hold down “+” of
the VOL switch (1). The volume will keep
on being increased until the switch is
released.
• To decrease the volume, hold down “-” of
the VOL switch (1). The volume will keep
on being decreased until the switch is
released.
• To mute the sound, press the switch (2). 6 H O H F W L Q J W K H P R G HPress the switch (3).
Each time the button is pressed, the mode
will change as follows:
(2)
(3)
(1)
(4)
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *