ECO mode SUZUKI NEXA 2015 1.G Owner's Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.
Page 106 of 288
Downloaded from www.Manualslib.com manuals search engine (1)
(2)
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details. , I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H L J Q L W L R Q P R G H V F D Q Q R W
E H V H O H F W H G
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
( ; $ 0 3 / (
(1)
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q
Page 113 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
method, there may be a problem else-
where, such as a low battery. Contact
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for inspection.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display will show a certain
message during this time. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.
• You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. Please contact an D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S for the
customization.
• If the battery of the remote controller is
about to be completely discharged, a
message warning this will appear on the
information display when the ignition
mode is changed to “ON” by pressing
the engine switch. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
5 H W X U Q L Q J W K H L J Q L W L R Q P R G H W R
³ / 2 & . ´ 2 ) )
Page 120 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
+ R Z W R 8 V H W K H 3 D U N L Q J 6 H Q V R U 3 D U N L Q J V H Q V R U V Z L W F K
61MS403
(1) Parking sensor switch
(2) Indicator
(2)
(1)
• When the ignition mode is “ON” and the indicator light in the parking sensor switch is on,
indicating that the parking sensor is ready for operation under the following conditions:
– The gearshift lever is in the “R” position.
– The vehicle’s forward moving speed is not more than approx. 9 km/h (6 mph) when
decelerating the vehicle such as for parking.
– The vehicle’s forward moving speed is not more than approx. 13 km/h (9 mph) when
accelerating.
• To deactivate the parking sensor, push the parking sensor switch and make sure the
indicator light goes off.
NOTE:
If you push the parking sensor switch from the OFF to ON position when the ignition mode
has been changed to ON by pressing the engine switch, the inside buzzer sounds. 6 Z L W F K S R V L W L R Q 6 W D W H ( ; $ 0 3 / (
ON
• When the indicator light is on and all necessary conditions are
met, system becomes ready for operation.
( ; $ 0 3 / (
OFF
• The system does not operate. Push the switch to turn off the
indicator if you do not wish to use the parking sensor.
Page 145 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
) U R Q W Z L W K R X W R Y H U K H D G F R Q V R O H
61MM0A205
Push the switch to turn on the light and
push it again to turn off the light.
) U R Q W Z L W K R Y H U K H D G F R Q V R O H
64MS119
& H Q W H U
61MM0A107
These light switches have three or four
positions with function as described below: 2 1 D
• The light comes on and stays on regard-
less of whether the door is open or
closed.
• To save the battery, the light will be auto-
matically turned off when a period of 15
minutes has elapsed after the light is on.
' 2 2 5 E
• The light comes on when the door is
opened. After closing all doors, the light
will remain on for about 15 seconds and
then fade out. If you insert the key, or
press the engine switch to change the
ignition mode to ACC or ON during this
time, the light will start to fade out imme-
diately. After removing the key from the
ignition switch, the light will turn on for
about 15 seconds and then fade out.
• Regardless of whether the door is open
or closed, the light comes on 15 seconds
and then fade out when the ignition
mode is changed to LOCK (OFF) or the
ignition switch is turned to the “LOCK”
position.
2 ) ) F
The light remains off even when the door is
opened.
6 3 2 7 / , * + 7 G
When the light switch is in the DOOR or
OFF position, push the switch to turn on
the light and push it again to turn off the
light. ( ; $ 0 3 / (
(d) (c) (b) (a) (d)
(a)
(b)
(c)
( ; $ 0 3 / (
Page 162 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
$ L U L Q W D N H V H O H F W R U
61MM0A020
This selector is used to select the following
modes.
) U H V K $ L U I
When this mode is selected, the indicator
light will go off and outside air is circulated
inside the cabin.
5 H F L U F X O D W H G $ L U J When this mode is selected, the indicator
light will come on, outside air is shut out and
inside air is recirculated. This mode is suit-
able when driving through dusty or polluted
air such as in a tunnel, or when attempting
to quickly cool down the interior.The "FRESH AIR" position (f) and RECIR-
CULATED AIR air position (g) are switched
alternately each time the air intake selector
is pushed.NOTE:
If you select the RECIRCULATED AIR posi-
tion (g) for an extended period of time, the
air in the vehicle can become contaminated.
Therefore, you should occasionally select
the “FRESH AIR” position (f).
$ L U F R Q G L W L R Q L Q J V Z L W F K To turn on the air conditioning system, set
the blower speed selector to the desired
blower speed position and push in the air
conditioning switch (5). With the air condi-
tioning switch operation, a indicator light will
come on when the air conditioning system
is on. To turn off the air conditioning system,
push the air conditioning switch again.
During operation of the air conditioner, you
may notice slight changes in engine speed.
These changes are normal, the system is
designed so that the compressor turns on
or off to maintain the desired temperature. Less operation of the compressor results
in better fuel economy.
6 \ V W H P 2 S H U D W L Q J , Q V W U X F W L R Q V 1 D W X U D O Y H Q W L O D W L R Q
Select the VENTILATION position (a) and
“FRESH AIR” position (f), the temperature
selector to the desired temperature posi-
tion, and turn off the blower. Fresh air will
flow through the vehicle during driving.
) R U F H G Y H Q W L O D W L R Q
The control settings are the same as for
natural ventilation except turning the
blower speed selector to turn on the
blower.
1 R U P D O K H D W L Q J X V L Q J R X W V L G H D L U
Select the HEAT position (c) and “FRESH
AIR” position (f), the temperature selector
to the desired temperature position and the
blower speed selector to the desired
blower speed position. Setting the blower
speed selector to a higher blower speed
position increases heating efficiency.
4 X L F N K H D W L Q J X V L Q J U H F L U F X O D W H G D L U
The control settings are the same as for
normal heating except selecting the
RECIRCULATED AIR air position (g). If
you use this heating method for an
extended period of time, the air in the vehi-
cle can become contaminated and the win-
dows can become misty. Therefore, use
this method only for quick heating and
change to the normal heating method as
soon as possible.
(f) (g)
Page 166 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% O R Z H U V S H H G V H O H F W R U
64MS052
The blower speed selector (2) is used to
turn on the blower and to select blower
speed.
If the “AUTO” switch (8) is pushed, the
blower speed will vary automatically as the
climate control system maintains the
selected temperature.
$ L U L Q W D N H V H O H F W R U
64MS053
Push the air intake selector (3) to change
between the following modes.
If the “AUTO” switch (8) is pushed, the air
intake will vary automatically as the climate
control system maintains the selected tem-
perature.
NOTE:
When you select the recirculated air mode,
the automatic operation system is deacti-
vated if you push the “AUTO” switch (8).
5 ( & , 5 & 8 / $ 7 ( ' $ , 5 D
When this mode is selected, outside air is
shut off and inside air is recirculated. This
mode is suitable when driving through an
area with polluted air such as a tunnel, or
when attempting to quickly cool down the
vehicle.
) 5 ( 6 + $ , 5 E
When this mode is selected, outside air is
introduced.
The “FRESH AIR” position (b) and RECIR-
CULATED AIR position (a) are selected
alternately each time the air intake selector
is pushed.
NOTE:
If you select the RECIRCULATED AIR
position (a) for an extended period of time,
the air in the vehicle can become contami-
nated. Therefore, you should occasionally
select the “FRESH AIR” position (b). ³ 0 2 ' ( ´ V Z L W F K
64MS054
Push the “MODE” switch (4) to change
among the following functions. The indica-
tion of the selected mode appears on the
display.
If the “AUTO” switch (8) is pushed, the air
flow will vary automatically as the climate
control system maintains the selected tem-
perature.
9 H Q W L O D W L R Q F
61M0100
(2)
(b) (a)
(3)
0 2 ' (
(4)
(c)
(d)
(e)
(f)
Page 178 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
6 H O H F W L Q J W K H ) 0 E D Q G
Press the FM button (1).
Each time the button is pressed, the recep-
tion band will change as follows:
6 H O H F W L Q J W K H $ 0 E D Q G
Press the AM button (2).
6 H H N W X Q L Q J
Press the seek Up button (3) or the seek
Down button (4).
The unit stops searching for a station at a
frequency where a broadcast station is
available.
0 D Q X D O W X Q L Q J
Turn the TUNE FOLDER PUSH SOUND
knob (5).
The frequency being received is displayed. 3 U H V H W P H P R U \
1) Select the desired station.
2) Hold down a desired button ([1] to [6])
of the Preset buttons (6) to which you
want to store the station for 2 seconds
or longer. $ X W R V W R U H
Hold down the AST button (7) for 2 sec-
onds or longer.
Six stations in good reception will automat-
ically be stored to the Preset buttons (6) in
order, starting from a station whose fre-
quency is the lowest.
NOTE:
• Auto store can be released by pressing
AST button (7) while auto store is under
way.
• When the auto store is performed, the
station previously stored in the memory
at the position is overwritten.
• When there are fewer than 6 stations
that can be stored even if 1 round of
auto store operation is performed, no
station will be stored at the remaining
Preset buttons (6).
• 6 stations can be preset for FM1 and
FM2 in common, and 6 stations for AM
in auto store mode.
$ X W R V W R U H P R G H R Q R I I
Press the AST button (7).
Each time the button is pressed, the mode
is switched as follows: 5 D G L R 5 H F H S W L R Q
Radio reception can be affected by envi-
ronment, atmospheric conditions, or radio
signal’s power and distance from the sta-
tion. Nearby mountains and buildings may
interfere or deflect radio reception, causing
poor reception. Poor reception or radio
static can also be caused by electric cur-
rent from overhead wires or high voltage
power lines. FM1 FM2
AST mode on AST mode off