steering wheel SUZUKI NEXA 2015 1.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 62 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
80J105E
• Collision with a fixed wall or guardrail at
an angle of greater than about 30
degrees (1) from the front
80J106
• In frontal collisions with a fixed wall that
does not move or deform at vehicle
speed of less than about 25 km/h (15
mph)
80J107
• Offset collision between two vehicles.
+ R Z W K H 6 \ V W H P : R U N VIn a frontal collision, the crash sensors will
detect rapid deceleration, and if the control-
ler judges that the deceleration represents a
severe frontal crash, the controller will trig-
ger the inflators. The inflators inflate the
appropriate air bags with nitrogen or argon
gas. The inflated air bags provide a cushion
for your head and upper body. The air bag
inflates and deflates so quickly that you may
not even realize that it has activated. The air
bag will neither hinder your view nor make it
harder to exit the vehicle.
Air bags must inflate quickly and forcefully
in order to reduce the chance of serious or
fatal injuries. However, an unavoidable con-
sequence of the quick inflation is that the air
bag may irritate bare skin, such as the facial
area against a front air bag. Also, upon
inflation, a loud noise will occur and some
powder and smoke will be released. These
conditions are not harmful and do not indi-
cate a fire in the vehicle. Be aware, how-
ever, that some air bag components may be
hot for a while after inflation.
A seat belt helps keep you in the proper
position for maximum protection when an air
bag inflates. Adjust your seat as far back as
possible while still maintaining control of the
vehicle. Sit fully back in your seat; sit up
straight; do not lean over the steering wheel
or dashboard. Front occupants should not
lean on or sleep against the door. Please
refer to the “Front Seat” section and the
“Seat Belts and Child Restraint Systems”
section in this section for details on proper
seat and seat belt adjustments.
65D610
(1)
: $ 5 1 , 1 *
Page 84 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
2 S H Q ' R R U : D U Q L Q J / L J K W
54G391
This light remains on until all doors (includ-
ing the tailgate) are completely closed.
If any door (including the tailgate) is open
when the vehicle is moving, a ding sounds
to remind you to close all doors completely.
/ R Z ) X H O : D U Q L Q J / L J K W
54G343
If this light comes on, fill the fuel tank
immediately.
When this light comes on, a ding sounds
once to remind you to fill the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to the “ON” position or the engine
switch is pressed to change the ignition
mode to ON.
NOTE:
The activation point of this light varies
depending on road conditions (for exam-
ple, slope or curve) and driving conditions
because of fuel moving in the tank.
( O H F W U L F 3 R Z H U 6 W H H U L Q J / L J K W
79J039
This light comes on when the ignition
switch is turned to the “ON” position or the
engine switch is pressed to change the
ignition mode to ON, and goes out when
the engine is started.
If this light comes on or blinks while driv-
ing, the power steering system may not
work properly. Have the system inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
NOTE:
While parking or driving at very low speed
greater steering effort is required. This is
not a malfunction of the steering system
but power steering control system limiting
power assist in order to prevent it from
over heating.
• The steering wheel is operated very
often.
• The steering wheel is kept in a fully
turned position for a long while.
When the power steering control system
cools down, the power steering system is
restored back to the original condition.
Page 97 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
5 H D U : L Q G R Z : L S H U : D V K H U 6 Z L W F K
L I H T X L S S H G
64MS068
To turn the rear wiper on, twist the rear
wiper switch on the end of the lever forward
to the “ON” position. If your vehicle is
equipped the “INT” position, the rear wiper
operates intermittently when you twist the
switch forward to the “INT” position. To turn
the rear wiper off, twist the switch rearward
to the “OFF” position.With the rear wiper in the “OFF” position,
twist the switch rearward and hold it there
to spray window washer fluid.
With the rear wiper in the “ON” position,
turn the switch forward and hold it there to
spray window washer fluid.
7 L O W 7 H O H V F R S L Q J L I H T X L S S H G 6 W H H U
L Q J / R F N / H Y H U
61MM0A085
(1) LOCK
(2) UNLOCK
The lock lever is located under the steering
column. To adjust the steering wheel
height and fore-aft position:
1) Push down the lock lever to unlock the
steering column.
2) Adjust the steering wheel to the desired
height and fore-aft position and lock the
steering column by pulling up the lock
lever.
3) Try moving the steering wheel up and
down and back and forth to make sure
it is securely locked in position.
( ; $ 0 3 / (
Intermittent wiper WasherWiper
NOTICE
& O H D U L F H R U V Q R Z I U R P W K H U H D U Z L Q
G R Z D Q G U H D U Z L S H U E O D G H E H I R U H
X V L Q J W K H U H D U Z L S H U $ F F X P X O D W H G
L F H R U V Q R Z F R X O G S U H Y H Q W W K H Z L S H U
E O D G H I U R P P R Y L Q J F D X V L Q J G D P D J H
W R W K H Z L S H U P R W R U
: $ 5 1 , 1 *
1 H Y H U D W W H P S W W R D G M X V W W K H V W H H U L Q J
Z K H H O Z K L O H W K H Y H K L F O H L V P R Y L Q J R U
\ R X F R X O G O R V H F R Q W U R O R I W K H Y H K L F O H
(2) ( ; $ 0 3 / (
( )
Page 98 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
+ R U Q
68LM240
Press the horn button of the steering wheel
to sound the horn. The horn will sound with
the ignition switch in any position or any
ignition mode.
+ H D W H G 5 H D U : L Q G R Z 6 Z L W F K L I
H T X L S S H G 7 \ S H
64MS167
7 \ S H
64MS168
When the rear window is misted, push this
switch (1) to clear the mist from the win-
dow.An indicator light will be lit when the defog-
ger is on. The defogger will work only
when the engine is running. To turn off the
defogger, push the switch (1) again.
NOTE:
• The defogger will work only when the
engine is running.
• The defogger will automatically turn off
after the defogger remains on for 15 min-
utes to prevent discharging of the bat-
tery.
REAR
12
3
04A/C
( ; $ 0 3 / (
(1)
( ; $ 0 3 / ( ( ; $ 0 3 / (
NOTICE
7 K H K H D W H G U H D U Z L Q G R Z X V H V D O D U J H
D P R X Q W R I H O H F W U L F L W \ % H V X U H W R W X U Q
R I I D I W H U W K H Z L Q G R Z D Q G P L U U R U V K D Y H
E H F R P H F O H D U
(1)
Page 103 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
You must push in the key to turn it to the
“LOCK” position. It locks the ignition, and
prevents normal use of the steering wheel
after the key is removed.
To release the steering lock, insert the key
and turn it clockwise to one of the other
positions. If you have trouble turning the
key to unlock the steering, try turning the
steering wheel slightly to the right or left
while turning the key.
$ & &
Accessories such as the radio can oper-
ate, but the engine is off.
2 1
This is the normal operating position. All
electrical systems are on.
6 7 $ 5 7
This is the position for starting the engine
using the starter motor. The key should be
released from this position as soon as the
engine starts.
, J Q L W L R Q N H \ U H P L Q G H U L I H T X L S S H G
A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
81A297S
: $ 5 1 , 1 *
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.
Page 115 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
& U X L V H & R Q W U R O L I H T X L S S H G The cruise control system allows you to
maintain a steady speed without keeping
your foot on the accelerator pedal. The
controls for operating the cruise control
system are on the steering wheel.
You can use the cruise control system with
the following conditions:
• The gear position is in 3rd, 4th, 5th or 6th
(if equipped).
• The vehicle speed is about 40 km/h (25
mph) or higher.
61MS416
(1) “CRUISE” switch
(2) “CANCEL” switch
(3) “RES +” switch
(4) “SET –” switch
7 R 6 H W & U X L V L Q J 6 S H H G1) Turn on the cruise control system by
pushing the “CRUISE” switch (1). When
the “CRUISE” indicator light comes on,
you can set cruising speed.
2) Accelerate or decelerate to the desired
speed.
3) Push the “SET –” switch (4) and the
“SET” indicator light will turn on. Take
your foot off the accelerator pedal and
the set speed will be maintained.
: $ 5 1 , 1 *
7 R K H O S D Y R L G O R V V R I Y H K L F O H F R Q W U R O
G R Q R W X V H W K H F U X L V H F R Q W U R O V \ V W H P
Z K H Q G U L Y L Q J L Q K H D Y \ W U D I I L F R Q V O L S
S H U \ R U Z L Q G L Q J U R D G V R U R Q V W H H S
G R Z Q J U D G H V
(1)(2)
(3)(4)
: $ 5 1 , 1 *
, I W K H F U X L V L Q J V S H H G L V V H W E \ D F F L
G H Q W \ R X F D Q Q R W G H F H O H U D W H D Q G P D \
O R R V H F R Q W U R O R I W K H Y H K L F O H 7 K L V
F R X O G O H D G W R D Q D F F L G H Q W U H V X O W L Q J L Q
V H Y H U H L Q M X U \ R U G H D W K
7 X U Q R I I W K H F U X L V H F R Q W U R O V \ V W H P
D Q G P D N H V X U H W K H
Page 127 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
% U D N H $ V V L V W 6 \ V W H P L I H T X L S S H G When you slam the brakes on, the brake
assist system judges as an emergency
stop and provides more powerful braking
for a driver who cannot hold down the
brake pedal firmly.
NOTE:
If you quickly and forcefully depress the
brakes, you may hear a clicking sound in
the brake pedal. This is normal and indi-
cates that the brake assist system is acti-
vated properly. $ Q W L / R F N % U D N H 6 \ V W H P $ % 6
L I H T X L S S H G ABS will help in avoiding locking of the
wheel by electronically controlling braking
pressure. It will also help you maintain
steering control when braking on slippery
surfaces or when braking hard”
The ABS works automatically, so you do
not need any special braking technique.
Just push the brake pedal down without
pumping. The ABS will operate whenever
it senses that the wheels are locking up.
You may feel the brake pedal moves a little
while the ABS is operating.
NOTE:
The ABS will not work if vehicle speed is
under about 10 km/h (6 mph).
63J081
(1) ABS warning light
(2) Brake system warning light
: $ 5 1 , 1 *
Page 133 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' U L Y L Q J R Q 6 O L S S H U \ 5 R D G V
60G089A
Under wet road conditions you should
drive at a lower speed than on dry roads
due to possible slippage of tires during
braking. When driving on icy, snow-cov-
ered, or muddy roads, reduce your speed
and avoid sudden acceleration, abrupt
braking, or sharp steering movements.
7 L U H & K D L Q VTire chains should only be used if they are
needed to increase traction or are required
by law. Make sure that the chains you use
are the correct size for your vehicle’s tires.
Also make sure that there is enough clear-
ance between the fenders and the chains
as installed on the tires.
Install the chains on the front tires tightly,
according to the chain manufacturer’s
instructions. Retighten the chains after
driving about 1.0 km (1/2 mile) if neces-
sary. With the chains installed, drive slowly.
, I < R X U 9 H K L F O H * H W V 6 W X F NIf your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between first gear and reverse. This will
create a rocking motion which may give
you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting.
Do not race the engine. Excessive
wheel spin will cause the tires to dig
deeper, making it more difficult to free
the vehicle.
2)
If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S or a roadside assistance
service. If a towing service is not
available in an emergency, your
vehicle may be tem-porarily towed by
a towing cable or chain secured to
the towing hook either on the front of
the vehicle or on the rear of the vehicle.
Refer to “Frame Hooks” in the
“OTHER CONTROLS AND
EQUIPMENT” section.
NOTICE
Page 169 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
• To return the blower speed selector (2),
air intake selector (3), and “MODE”
switch (4) to automatic operation, push
the “AUTO” switch (8).
64MS149
Be careful not to cover the interior tem-
perature sensor (10) located between the
steering wheel and the climate control
panel, or the solar sensor (11) located at
the top of the central part of the dash-
board. These sensors are used by the
automatic system to regulate temperature.
0 D Q X D O R S H U D W L R Q
You can manually control the climate con-
trol system. Set the selectors to the
desired positions.
64MS091
NOTE:
If you need maximum defrosting:
• push the defrost switch (5) to turn on the
defroster (the air conditioning system will
come on and the fresh air position (b)
will be selected automatically),
• set the blower speed selector to HIGH,
• adjust the temperature selector to the
“HI” indication on the display, and
• adjust the side outlets so the air blows
on the side windows.
0 D L Q W H Q D Q F HIf you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
If your air conditioner is equipped with air
filters, clean or replace them as specified
in the “Maintenance Schedule” in the