drive shaft SUZUKI SWIFT 2000 1.G SF310 Service User Guide

6-32 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates opening of the throttle valve
in terms of percentage to opening controllable by the
ISC actuator.
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-69
Below
specified value DTC DETECTING CONDITION
POSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: –10 – 11 0C, 14 – 230F
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.

6-84 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Vehicle speed sensor (on A / T)
Counter
shaft
gearPCMC03-2
C03-13
Bl
P
C03-2
C03-13
DTC P0500 VEHICLE SPEED SENSOR (VSS) MALFUNCTION FOR A / T
VEHICLE (A / T)
CIRCUIT DESCRIPTION – Refer to Section 6E1 for VSS operation.
DTC DETECTING CONDITIONPOSSIBLE CAUSE

While fuel is kept cut at lower than 4000 r / min for
longer than 4 sec.

VSS signal not inputted.
2 driving cycle detection logic, continuous
monitoring.
“BI” or “P” circuit open or short.

Vehicle speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC and warm up engine to normal operating temperature.
3) Increase vehicle speed to 50 mph, 80 km / h in “2” range.
4) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 4 sec.
or more.
5) Stop vehicle and check DTC and pending DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

Below
specified value
6-1-70 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
1. CKP sensor signal
2. No.1 fuel injector signal
3. No.3 fuel injector signal
4. Fuel injection time
Display of fuel injection signal using oscilloscope
Waveforms at specified idle speed5ms/Div
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction

EGR system malfunction
DTC CONFIRMATION PROCEDURE
NOTE:
Among different types of random misfire, if misfire occurs at cylinders 1 and 4 or cylinders 3 and 2 simulta-
neously, it may not possible to reconfirm DTC by using the following DTC confirmation procedure. When
diagnosing the trouble of DTC P0300 (Random misfire detected) of the engine which is apparently misfir-
ing, even if DTC P0300 cannot be reconfirmed by using the following DTC confirmation procedure, pro-
ceed to the following Diag. Flow Table.
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: –10C, 14F or higher
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.
Reference

Output shaft speed sensor (on A / T)
Counter
shaft
gear
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-89
DTC P0500 VEHICLE SPEED SENSOR (VSS) MALFUNCTION FOR A / T
VEHICLE
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

While fuel is kept cut at lower than 4000 r / min for
longer than 4 sec.

VSS signal not inputted.
2 driving cycle detection logic, continuous
monitoring.
“P” or “Bl” circuit open or short.

Vehicle speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC and warm up engine to normal operating temperature.
3) Increase vehicle speed to 50 mph, 80 km / h in “2” range.
4) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 4 sec.
or more.
5) Stop vehicle and check DTC and pending DTC.

1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Spring damper
6. Camshaft timing pulley
7. Pin
8. Pulley bolt
9. Seal
10. Inside cover seal
11. Inside cover
12. Outside cover seal
13. Outside cover
14. Tensioner stud
15. Tensioner bolt
16. Tensioner spring screw
: Tightening Torque
6A-10 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle.
3) Remove clip (2) after pushing center pin, and then remove fend-
er apron extension (1) on right side.
NOTE:
Do not push center pin (3) too far in, or it will fall off into
fender.
4) Remove air cleaner assembly as previously outlined.
5) Remove A / C compressor drive belt, if equipped.
6) Loosen water pump pulley bolts (1).
7) Loosen generator pivot bolts (3) and its adjusting bolt (2) and re-
move water pump belt (4) and its pulley (5).

1. Crank timing belt pulley bolt
Direction of crankshaft
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-13
3) Check that timing mark (3) on camshaft timing belt pulley (1) is
aligned with “V” mark (2) on cylinder head cover (4). If not, align
two marks by turning camshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
4) Check that punch mark (2) on crank timing belt pulley (4) is
aligned with arrow mark (3) on oil pump case. If not, align two
marks by turning crankshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
5) With two sets of marks aligned, install timing belt (1) on two pul-
leys in such a way that the drive side of belt is free of any slack,
and with tensioner plate pushed up by finger.
And then install tensioner spring and spring damper (2) as
shown in figure, and handtighten tensioner stud.
NOTE:

When installing timing belt, match arrow mark (
) on
timing belt with rotating direction of crankshaft.

In this state, No.1 piston is at top dead center of compres-
sion stroke.
6) To take up slack of timing belt, turn crankshaft two rotations
clockwise after installing it. After making sure that belt is free
from slack, tighten tensioner stud (1) first and then tensioner bolt
(2) to each specified torque.
Then confirm again that two sets of marks are aligned respec-
tively.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 27 N
.m (2.7 kg-m, 19.5 lb-ft)

1. Rear mounting
2. Left mounting
3. Left mounting bracket
4. Right mounting
5. Right mounting bracket
For M / T model
For A / T model
1. Rear mounting
2. Rear mounting No.2
bracket
3. Rear mounting No.1
bracket
4. Left mounting No.1
bracket
5. Stopper6. Left mounting
7. Left mounting No.2
bracket
8. Right mounting bracket
9. Right mounting
10. Torque rod bracket
11. Stiffener
12. Torque rod
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-25
11) Disconnect the following cables.

Accelerator cable from throttle body.

Clutch cable from transmission. (For M / T model)

Gear select cable and oil pressure control cable from trans-
mission. (For A / T model)

Speedometer cable from transmission.
12) Hoist vehicle.
13) Remove fender apron extensions.
14) Remove exhaust pipe from exhaust manifold (or WU-TWC).
15) Remove gear shift control shaft from transmission and remove
extension rod. (For M / T model)
16) Drain engine oil and transmission oil.
17) Remove drive shaft joints from differential gears of transmis-
sion.
Refer to Section 4 (DRIVE SHAFT) for procedure to disconnect
drive shaft joints.
For engine and transmission removal, it is not necessary to re-
move drive shafts from steering knuckle.
18) Remove A / C compressor (if equipped) from compressor
bracket with hose still attached.
NOTE:
Suspend removed A / C compressor at a place where no
damage will be caused during removal / installation of en-
gine with transmission.
19) Remove engine rear torque rod bracket from transmission.
(For A / T model)
20) Lower vehicle.
21) Install lifting device.
22) Remove rear mounting from body.
23) Remove left side engine mounting and bracket. (For M / T mod-
el)
Remove left mounting from body. (For A / T model)
24) Remove right side engine mounting from its bracket.
25) Before removing engine with transmission, recheck to make
sure all hoses, electric wires and cables are disconnected from
engine and transmission.
26) Remove engine with transmission from body.

1. Rear mounting
2. Rear mounting No.2
bracket
3. Rear mounting No.1
bracket
4. Rear mounting
bracket5. Left mounting
body bracket
6. Left mounting
7. Left mounting bracket
8. Right mounting bracket
9. Right mounting
For M / T model
For A / T model
1. Rear mounting
2. Rear mounting No.2
bracket
3. Rear mounting No.1
bracket
4. Left mounting No.1
bracket
5. Stopper6. Left mounting
7. Left mounting No.2
bracket
8. Right mounting bracket
9. Right mounting
10. Torque rod bracket
11. Stiffener
12. Torque rod
6A-26 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
INSTALLATION
1) Lift engine with transmission into engine compartment, but do
not remove lifting device.
2) Install right side engine mounting to its bracket.
3) Install left side engine mounting and its bracket.
4) Install rear mounting to body.
5) Tighten bolts and nuts of all parts installed in above steps 2),
3) and 4) to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
6) Remove lifting device.
7) Reverse removal procedures for installation of remainder.

Push in each drive shaft joint fully so that snap ring engages
with differential gear or center bearing support.
Use care not to damage oil seal lip when inserting.

Clamp electric wires securely.
8) Adjust clutch pedal free travel referring to Section 7C. (For M / T
model)
Adjust gear select cable and oil pressure control cable referring
to Section 7B. (For A / T model)
9) Adjust gear shift control lever referring to Section 7A. (For M / T
model)
10) Refill transmission with gear oil. (A / T fluid for A / T model) refer-
ring to Section 0B.
11) Refill engine with engine oil referring to Section 0B.
12) Refill cooling system referring to Section 6B.
13) Adjust A / C compressor drive belt referring to Section 0B. (if
equipped)
14) Upon completion of installation, verify that there is no fuel leak-
age, coolant leakage, transmission oil leakage or exhaust gas
leakage at each connection.
15) Adjust accelerator cable play referring to Section 6E.