Position sensor SUZUKI SWIFT 2000 1.G SF310 Service Owner's Guide

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-31
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates current flow time rate within
a certain set cycle of IAC valve (valve opening rate)
which controls the amount of bypass air (idle speed).
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

6-1-34 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
CONNECTOR “C01”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1Ground——
2Ground——
3Ground——
4EVAP canister purge valve10 – 14 VIgnition switch ON
Indication
deflection
5Power steering switch
deflection
repeated
0 V and
Ignition switch ON
0 V and
10 – 14 V
6Idle air control valve0 – 13 VAt specified idle speed after engine warmed
up
7Heater of HO2S-110 – 14 VIgnition switch ON
8Fuel injector NO.410 – 14 VIgnition switch ON
9Fuel injector NO.110 – 14 VIgnition switch ON
10Sensor ground——
11Camshaft position sensor0 – 0.8 V
and 4 – 6 VIgnition switch ON
12Blank——
13Heater oxygen sensor-1Refer to DTC P0130 diag. flow table
14Engine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
15Intake air temp. sensor2.0 – 2.7 VIgnition switch ON
Intake air temp.: 20C (68F)
16Blank——
17Electric load signal (+)
0 – 1 VIgnition switch ON
Small light and rear defogger OFF
17Electric load signal (+)
10 – 14 VIgnition switch ON
Small light and rear defogger ON
18Blank——
19Ignition coil #2——
20Ignition coil #1——
21Fuel injector NO.210 – 14 VIgnition switch ON
22Power source for sensor4.75 – 5.25 VIgnition switch ON
23Crankshaft position sensor (+)——
24Crankshaft position sensor (–)——
25Blank——
26Manifold absolute pressure
sensor3.3 – 4.0 VIgnition switch ON
Barometric pressure: 100 kPa (760 mmHg)
27Blank——
28Immobilizer indicator lamp0 – 2 VIgnition switch ON28Immobilizer indicator lamp10 – 14 VWhen engine running
29Blank——
30Blank——
31Fuel injector NO.310 – 14 VIgnition switch ON

6-1-36 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
CONNECTOR “C03”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1Malfunction indicator lamp0 – 1 VIgnition switch ON1Malfunction indicator lamp10 – 14 VWhen engine running
2
Vehicle speed sensor (M / T)
Indicator
deflection
repeated
0 V and
4 – 6 V
Ignition switch ON
Front left tire turned slowly with front right
tire locked
Output shaft speed sensor
(+) (A / T)0.4 – 0.8 VIgnition switch ON
3Blank——
4Shift solenoidA(A / T)0 VIgnition switch ON, Select lever at P-range4Shift solenoid – A (A / T)10 – 14 VIgnition switch ON, Select lever at D-range
5Throttleposition sensor
0.2 – 1.0 VIgnition switch ON
Throttle valve at idle position
5Throttle position sensor
2.8 – 4.8 VIgnition switch ON
Throttle valve at full open position
6Ignition switch10 – 14 VIgnition switch ON
7Data link connector—Ignition switch ON
8Output shaft speed sensor
(–) (A / T)0.4 – 0.8 VIgnition switch ON
9Blank——
10Sensor ground——
11Shift solenoidB(A / T)0 VIgnition switch ON, Select lever at P-range11Shift solenoid – B (A / T)10 – 14 VIgnition switch ON, Select lever at D-range
12Blank——
13Blank——
14Blank——
15Blank——
16Tachometer (if equipped)0 – 1 VIgnition switch ON
17Engine start switch6 – 12 VWhile engine cranking17g
(Engine start signal)0 – 1 VOther than above

Throttle
position
sensorTo MAP sensor
To other sensors
6-1-50 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC P0120 THROTTLE POSITION CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Signal voltage high

Signal voltage low
“G” circuit open

“Gr” circuit open or shorted to ground

“P” circuit open or shorted to power or ground

TP sensor malfunction

ECM (PCM) malfunction
NOTE:

When DTC P0105, P0110, P0115 and / or P0120 are / is indicated together, it is possible that “G” circuit is
open.

When DTC P0105 and / or P0120 are / is indicated together, it is possible that “P” circuit is open.
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-51
Fig. 1 for Step 2 Fig. 2 for Step 3 Fig. 3 for Step 4
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE”
performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check TP Sensor and Its Circuit.
1) Connect scan tool to DLC with ignition
switch OFF and then turn ignition switch
ON.
2) Check throttle valve opening percentage
displayed on scan tool. See Fig. 1.
Is it displayed 2% or less?
3) Check throttle valve opening percentage
displayed on scan tool while opening
throttle valve from idle position to full open
position. See Fig. 1.
Is it displayed 96% or higher?Go to Step 3.Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection” in
Section 0A.
3Check Wire Harness.
1) Disconnect connector from TP sensor
with ignition switch OFF.
2) Check for proper connection to TP sensor
at “P”, “Gr” and “G” wire terminal.
3) If OK, then with ignition switch ON, check
voltage at each of “P” and “Gr” wire
terminals. See Fig. 2.
Is voltage about 4 – 6 V at each terminal?Go to Step 4.“P” wire open, “P” wire
shorted to ground circuit or
power circuit or “G” wire,
“Gr” wire open or shorted
to ground circuit or poor
C01-22 or C03-5
connection.
If wire and connection are
OK, substitute a known-
good ECM (PCM) and
recheck.
4Check TP Sensor.
1) Check resistance between terminals of
TP sensor. See Fig. 3.
Between 1 and 2: 2.5 – 6.0 kΩ
Between 1 and 3: 170 Ω – 15.5 kΩ
Are measured values within specifications?“G” wire open or poor
C01-10 connection.
If wire and connection are
OK, substitute a known-
good ECM (PCM) and
recheck.Replace TP sensor.

6-1-52 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Throttle
position
sensorTo other sensors
To other sensors
DTC P0121 THROTTLE POSITION CIRCUIT RANGE / PERFORMANCE
PROBLEM
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

After engine warmed up.

While vehicle running at specified engine speed.

No change in intake manifold pressure (constant throttle opening)

Difference between actual throttle opening (detected from TP sensor)
and opening calculated by ECM (PCM) (Obtained on the basis of
engine speed and intake manifold pressure) in larger than specified
value.
2 driving cycle detection logic, continuous monitoring
TP sensor malfunction

High resistance in the circuit

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF. Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Indication of fuel level meter in combination meter: 1 / 4 or more
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Intake air temp.: between –10C and 80C (14F and 176F)
–Engine coolant temp.: 70C, 158F or higher
2) Warm up engine to normal operating temperature.
3) Increase vehicle speed to 30 – 40 mph, 50 – 60 km / h in 3rd gear or “D” range and hold throttle valve at that
opening position for 1 min.
4) Stop vehicle.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-53
Fig. 1 for Step 2 Fig. 2 for Step 2 Fig. 3 for Step 2
Fig. 4 for Step 3
Closed
(condition “A”)Fully open
Throttle Opening When using SUZUKI scan tool:
When not using SUZUKI scan tool:
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE
DIAG. FLOW
TABLE”.
2Check TP Sensor and Its Circuit.
When using SUZUKI scan tool:
1) Turn ignition switch OFF and connect SUZUKI scan tool to
DLC.
2) Turn ignition switch ON and check TP sensor output
voltage when throttle valve is at idle position and fully
opened. See Fig. 1 and 3.
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminal C03-5 of ECM (PCM) connector
connected, when throttle valve is at idle position and fully
opened. See Fig. 2 and 3.
Dose voltage vary within specified value linearly as shown in
figure?If voltmeter was
used, check
terminal C03-5 for
poor connection.
If OK, substitute a
known-good ECM
(PCM) and
recheck.Go to Step 3.
3Check TP Sensor.
1) Turn ignition switch OFF.
2) Disconnect TP sensor connector.
3) Check for proper connection to TP sensor at each terminal.
4) If OK, then measure resistance between terminals and
check if each measured value is as specified below.
See Fig. 4.
Between 1 and 2: 2.5 – 6.0 kΩ
Between 1 and 3: 170 Ω – 15.5 kΩ, varying according to
throttle valve opening.
Are measured values as specified?High resistance in
“P”, “Gr” or “G”
circuit.
If wire and
connection are
OK, substitute a
known-good ECM
(PCM) and
recheck.Replace TP
sensor.

6-1-68 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Fig. 1 for Step 3 Fig. 2 for Step 4 Fig. 3 for Step 5
Fig. 4 for Step 5 Fig. 5 for Step 5 Fig. 6 for Step 6
1. Fuel delivery pipe
2. Fuel feed hose
3. Fuel pressure gauge &
3 way joint
STEPACTIONYESNO
8Check engine coolant temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 9.Replace engine
coolant temp. sensor.
9Check intake air temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 10.Replace intake air
temp. sensor.
10Check throttle position sensor for performance (See
Step 3 of DTC P0121 Diag. Flow Table).
Is it in good condition?Go to Step 11.Replace throttle
position sensor.
11Check PCV valve for valve clogging
(See Section 6E2).
Is it good condition?Substitute a known-
good ECM (PCM) and
recheck.Replace PCV valve.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-69
Ignition coil assembly
for No.1 & No.4 spark plugs
Ignition coil assembly
for No.2 & No.3 spark plugs
Ignition switch
Main relay
Main
fuseRelay box
To ignition switch
CKP sensorCMP sensorNo.1 injector
No.2 injector
No.3 injector
No.4 injector Fuse box
DTC P0300 RANDOM MISFIRE DETECTED (Misfire detected at 2 or more
cylinders)
DTC P0301 CYLINDER 1 MISFIRE DETECTED
DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0303 CYLINDER 3 MISFIRE DETECTED
DTC P0304 CYLINDER 4 MISFIRE DETECTED
CIRCUIT DESCRIPTION
ECM (PCM) monitors crankshaft revolution speed and engine speed via the crankshaft position sensor and cylin-
der No. via the camshaft position sensor. Then it calculates the change in the crankshaft revolution speed and from
how many times such change occurred in every 200 or 1000 engine revolutions, it detects occurrence of misfire.
When ECM (PCM) detects a misfire (misfire rate per 200 revolutions) which can cause overheat and damage to
the three way catalytic converter, it makes the malfunction indicator lamp (MIL) flash as long as misfire occurs at
that rate.
After that, however, when the misfire rate drops, MIL remains ON until it has been judged as normal 3 times under
the same driving conditions.
Also, when ECM (PCM) detects a misfire (misfire rate per 1000 revolutions) which will not cause damage to three
way catalytic converter but can cause exhaust emission to be deteriorated, it makes MIL light according to the 2
driving cycle detection logic.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-73
Crankshaft
timing belt
pulleyCKP
sensor
Oscilloscope Waveforms
Waveforms at engine cranking (260 r/min) Waveforms at specified idle speed16 waives
for 10 signals13 waives for
10 signals
30 signal 30 signal 0.5 V / Div.
10 ms / Div.0.5 V / Div.
5 ms / Div.
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

NO CKP sensor signal for 2 seconds at engine
cranking.
CKP sensor circuit open or short.

Crankshaft timing belt pulley teeth damaged.

CKP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-23 (+) and C01-24 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC and crank engine for 2 sec.
2) Select “DTC” mode on scan tool and check DTC.