engine oil SUZUKI SWIFT 2000 1.G SF310 Service Repair Manual

3 / 4 turn
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-3
3) Install special tool (Oil pressure gauge) to vacated threaded
hole.
Special Tool
(A): 09915-77311
(B): 09915-78211
NOTE:
At this time, be very careful not to exert force to where
heated oxygen sensor and its lead wire are connected.
4) Reinstall oil filter.
5) Start engine and warm it up to normal operating temperature.
6) After warming up, raise engine speed to 4,000 r / min and mea-
sure oil pressure.
Oil pressure specifications: 270 – 370 kPa
(2.7 – 3.7 kg / cm
2,
38.4 – 52.6 psi) at
4,000 r / min (rpm)
7) After checking oil pressure, stop engine and remove oil filter
and oil pressure gauge.
8) Before reinstalling oil pressure switch (1), be sure to wrap its
screw threads with a sealing tape and tighten switch to speci-
fied torque.
NOTE:
If sealing tape edge is bulged out from screw threads of
switch, cut it off.
Tightening Torque
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)
9) After oiling oil filter “O” ring (rubber gasket), screw oil filter on
oil filter stand by hand until filter “O” ring contacts mounting sur-
face.
CAUTION:
To tighten oil filter properly, it is important to accurately
identify the position where filter “O” ring first contacts
mounting surface.
10) Tighten filter (1) 3 / 4 (270) turn from the point of contact with
mounting surface using an oil filter wrench.
Special Tool
(C): 09915-47310
CAUTION:
To prevent oil leakage, make sure that oil filter is tight,
but do not overtighten it.
11) After installing oil filter, start engine and check oil filter for oil
leakage.

1.“V” mark on cylinder head cover
2. Timing mark on camshaft timing belt pulley
3. Arrow mark on oil pump case
4. Punch mark on crankshaft timing belt pulley
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-11
8) Loosen crankshaft pulley bolts (1) and remove crankshaft
pulley (2).
9) Remove timing belt outside cover (1).
10) Align 4 timing marks as shown in figure to facilitate its installa-
tion.
11) Loosen tensioner bolt (3) and stud (4), and remove belt (1) from
crankshaft timing belt pulley and camshaft timing belt pulley af-
ter pushing up the tensioner plate (2) fully by finger as shown
figure.
CAUTION:
Never bend timing belt.

6A-12 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
1. Camshaft allowable turning range – – – By timing
mark, within 90 from “V” mark on head cover on
both right and left.
2. Crankshaft allowable turning range – – – by punch
mark, within 90 from arrow mark on oil pump case
on both right and left.
CAUTION:
After timing belt is removed, never turn camshaft and crank-
shaft independently more than such an extent as shown be-
low. If turned, interference may occur among piston and
valves, and parts related to piston and valves may be dam-
aged.
12) Remove tensioner, tensioner plate, tensioner spring and
spring damper.
INSPECTION

Check timing belt for wear or crack. Replace it as necessary.

Check tensioner for smooth rotation and rattle.
INSTALLATION
1) Install tensioner plate (1) to tensioner (2).
Insert lug (3) of tensioner plate into hole (4) of tensioner.
2) Install tensioner (2) and tensioner plate (3).
Do not tighten the tensioner bolt (1) and stud by wrench yet.
Hand tighten only at this time.
Check to ensure that plate movement in arrow direction as
shown in figure causes tensioner to move in the same direction.
If no associated movement between plate and tensioner occurs,
remove tensioner and plate again and reinsert the plate lug into
tensioner hole.

1. Crank timing belt pulley bolt
Direction of crankshaft
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-13
3) Check that timing mark (3) on camshaft timing belt pulley (1) is
aligned with “V” mark (2) on cylinder head cover (4). If not, align
two marks by turning camshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
4) Check that punch mark (2) on crank timing belt pulley (4) is
aligned with arrow mark (3) on oil pump case. If not, align two
marks by turning crankshaft but be careful not to turn it more
than its allowable turning range which is described on previous
page.
5) With two sets of marks aligned, install timing belt (1) on two pul-
leys in such a way that the drive side of belt is free of any slack,
and with tensioner plate pushed up by finger.
And then install tensioner spring and spring damper (2) as
shown in figure, and handtighten tensioner stud.
NOTE:

When installing timing belt, match arrow mark (
) on
timing belt with rotating direction of crankshaft.

In this state, No.1 piston is at top dead center of compres-
sion stroke.
6) To take up slack of timing belt, turn crankshaft two rotations
clockwise after installing it. After making sure that belt is free
from slack, tighten tensioner stud (1) first and then tensioner bolt
(2) to each specified torque.
Then confirm again that two sets of marks are aligned respec-
tively.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 27 N
.m (2.7 kg-m, 19.5 lb-ft)

6A-14 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
7) Install timing belt outside cover.
Before installing, make sure that rubber seal (1) is between wa-
ter pump and oil pump case and another between water pump
and cylinder head.
Tightening Torque
(c): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
8) Install crankshaft pulley (2).
Tighten crankshaft pulley bolts (1).
Tightening Torque
(d): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
9) Install water pump pulley and water pump belt.
Adjust the belt tension to the specification.
Refer to Section 6B for procedure to adjust the belt tension.
10) Install air cleaner assembly.
11) Install fender apron extension of right side.
12) Connect negative cable at battery.

1. Cylinder head cover
2. Gasket
3. Cylinder head
4. Camshaft housing No.1:
Apply sealant 99000-31110 to mating surface.
5. Camshaft housing No.2
6. Camshaft housing No.3:
Apply sealant 99000-31110 to mating surface.
7. Camshaft
8. Oil seal
9. Valve lash adjuster
10. Camshaft housing bolt
1. Crankshaft timing belt pulley: Tightening Torque
: Apply engine oil to sliding
: surfaces of each part.
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-15
CAMSHAFT AND HYDRAULIC VALVE LASH ADJUSTER
REMOVAL
1) Disconnect negative cable at battery.
2) Remove cylinder head cover as previously outlined.
3) Remove distributor and then its case from cylinder head.
4) Remove crankshaft pulley, timing belt outside cover and timing
belt as previously outlined.
After removing timing belt, set key (2) on crankshaft in position
as shown in figure by turning crankshaft. This is to prevent inter-
ference between valves and piston when reinstalling camshaft.
5) Remove camshaft timing belt pulley (1).
Lock camshaft (2) with a proper size rod (3) inserted into hole (10
mm, 0.39 in.) in it as shown and then loosen camshaft timing belt
pulley bolt.
NOTE:
Mating surfaces of cylinder head and cover must not be
damaged in this work. So, put clean shop cloth (4) between
rod and mating surfaces, and use care not to bump rod
against mating surfaces hard when loosening bolt.

Don’t apply force
6A-16 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
6) Remove camshaft housings from cylinder head.
7) Remove camshaft from cylinder head.
8) Remove valve lash adjuster from cylinder head.
NOTE:

Never disassemble hydraulic valve lash adjuster.

Don’t apply force to body of adjuster, for oil in high pres-
sure chamber in adjuster will leak.

Immerse removed adjuster (2) in clean engine oil (1) and
keep it there till reinstalling it so as to prevent oil leakage.
If it is left in air, place it with its bucket body facing down.
Don’t place on its side or with bucket body facing up.

Indicates position from timing belt
side. Install in numerical order
starting from timing belt side.

Indicates direction of housing.
Install so that arrow is directed
toward timing belt side.
6A-18 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
INSTALLATION
1) Before installing valve lash adjuster to cylinder head, fill oil pas-
sage of cylinder head (1) with engine oil according to the follow-
ing procedure.
Pour engine oil through camshaft journal oil holes (2) and check
that oil comes out from oil holes in sliding part of valve lash ad-
juster.
2) Install lash adjuster to cylinder head.
Apply engine oil around valve lash adjuster and then install it to
cylinder head.
3) Install camshaft to cylinder head.
After applying engine oil to camshaft journal and all around cam,
set camshaft to cylinder head so that camshaft timing belt pulley
pin hole (1) in camshaft is at lower position.
4) Install camshaft housing to camshaft and cylinder head.

Apply engine oil to sliding surface of each housing against
camshaft journal.

Apply sealant to mating surface of No.1 and No.3 housings
which will mate with cylinder head.
“A”: Sealant 99000-31110

Embossed marks are provided on each camshaft housing, in-
dicating position and direction for installation.
Install housing as indicated by these marks.

2. No.2 housing
3. No.3 housing
3. Rod
4. Shop cloth
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-19

As camshaft housing No.1 (1) retains camshaft in proper
position as to thrust direction, make sure to first fit No.1 hous-
ing to No.1 journal of camshaft securely.

After applying engine oil to housing bolts, tighten them tem-
porarily first. Then tighten them by following sequence as
shown in figure.
Tighten a little at a time and evenly among bolts and repeat
tightening sequence three to four times before they are tight-
ened to specified torque.
Special Tool
(A): 09919-16010
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Install camshaft oil seal.
After applying engine oil to oil seal lip, press-fit camshaft oil
seal till oil seal surface becomes flush with housing surface.
6) Install camshaft timing belt pulley (1) to camshaft (2) after
installing dwell pin to camshaft.
With locking camshaft as shown in figure, tighten pulley bolt to
specified torque.
Tightening Torque
(b): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
7) Install cylinder head cover to cylinder head as previously out-
lined.
8) Install timing belt, timing belt outside cover, crankshaft pulley,
water pump pulley and water pump belt as previously outlined.
9) Install distributor case and distributor.
Refer to Section 6F for installation.
10) Install air cleaner assembly as previously outlined.
11) Connect negative cable at battery.
12) Adjust ignition timing.
Refer to Section 6F for adjustment.

6A-20 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
CAUTION:

Don’t turn camshaft or start engine (i.e., valves should not be operated) for about half an hour after
reinstalling hydraulic valve lash adjusters and camshaft. As it takes time for valves to settle in place,
operating engine within half an hour after their installation may cause interference to occur between
valves and piston.

If air is trapped in valve lash adjuster, valve may make tapping sound when engine is operated after
valve lash adjuster is installed. In such a case, run engine for about half an hour at about 2,000 – 3,000
r / min., and then air will be purged and tapping sound will cease. Should tapping should not cease,
it is possible that valve lash adjuster is defective. Replace it if defective.
If defective adjuster can’t be located by hearing among 6 of them, check as follows.
1) Stop engine and remove cylinder head cover.
2) Push adjuster downward by hand (with less than 15 kg or 33 lbs force) when cam crest is not on
adjuster to be checked and check if clearance exists between cam and adjuster. If it does, adjuster
is defective and needs replacement.
VALVE LASH ADJUSTER NOISE DIAGNOSIS
In case of the followings, valve lash adjuster noise may be caused by air trapped into valve lash adjusters.

Vehicle is left for 24 hours or more.

Engine oil is changed.

Hydraulic lash adjuster is replaced or reinstalled.

Engine is overhauled.
If noise from valve lash adjusters is suspected, perform the following checks.
1) Check engine oil for the followings.

Oil level in oil pan
If oil level is low, add oil up to Full level hole on oil level gauge.

Oil quality
If oil is discolored, or deteriorated, change it.
For particular oil to be used, refer to Section 0B.

Oil leaks
If leak is found, repair it.

Oil pressure (refer to Oil Pressure Check in this section)
If defective pressure is found, repair it.
2) Run engine for about half an hour at about 2,000 to 3,000 r / min., and then air will be purge and tapping sound
will cease.
3) Should tapping sound not cease, it is possible that hydraulic valve lash adjuster is defective.
Replace it if defective.
If defective adjuster can’t be located by hearing among 16 of them, check as follows.
a) Stop engine and remove cylinder head cover.
b) Push adjuster downward by hand (with less than 20 kg or 44 lbs. Force) when cam crest is not on adjuster
to be check if clearance exists between cam and adjuster.
If it does, adjuster is defective and needs replacement.