cam SUZUKI SWIFT 2000 1.G SF310 Service Repair Manual

3
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-11
AIR CLEANER ELEMENT
REMOVAL
1) Disconnect air cleaner outlet hose from case after loosening its
clamp (2) and removing bolt (1) shown in figure.
2) Remove air cleaner cap (3) from case by unhooking its clamps,
then take out air cleaner element.
INSPECTION
Check air cleaner element for dirt. Replace excessively dirty ele-
ment.
CLEAN
Blow off dust by compressed air from air outlet side of element.
INSTALLATION
Reverse removal procedure for installation.

6A1-12 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
AIR CLEANER OUTLET HOSE
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect resonator after loosening its clamp.
3) Disconnect breather hose from air cleaner outlet hose.
4) Disconnect IAT sensor wire at coupler.
5) Remove bolt and then air cleaner outlet hose after loosening its
clamps.
INSTALLATION
Reverse removal procedure for installation, noting the following.

Clamp each hose securely.

3
3
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-13
CYLINDER HEAD COVER
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect breather hose (2) and PCV valve (3) from head cov-
er.
3) Disconnect ignition coil couplers (6).
4) Remove ignition coil assemblies (5) with high-tension cord (4).
5) Remove cylinder head cover (1) with cylinder head cover gasket
and O-rings.
INSTALLATION
1) Install O-rings (3) and cylinder head cover gasket (2) to cylinder
head cover (1).
NOTE:
Be sure to check each of these parts for deterioration or any
damage before installation and replace if found defective.
2) Install cylinder head cover to cylinder head and tighten cover
bolts to specified torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
NOTE:
When installing cylinder head cover, use care so that cylin-
der head cover gasket or O-rings will not get out of place or
fall off.
3) Install ignition coil assemblies (5) with high-tension cord (4).
4) Connect ignition coil couplers (6).
5) Connect breather hose (2) and PCV valve (3) to head cover (1).
6) Connect negative cable at battery.

1. Intake manifold
2. Throttle body
3. Gasket
4. EGR valve
5. Fuel delivery pipe
6. Fuel injector7. Fuel pressure regulator
8. EVAP canister purge valve
9. MAP sensor
10. O-ring
11. Gasket
12. Cushion : Tightening Torque
: Do not reuse
1
2
6A1-14 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
THROTTLE BODY AND INTAKE MANIFOLD
REMOVAL
1) Relieve fuel pressure according to procedure described in Sec-
tion 6.
2) Disconnect negative cable at battery.
3) Drain cooling system.
WARNING:
To help avoid danger of being burned, do not remove
drain plug (2) and radiator cap while engine and radiator
(1) are still hot. Scalding fluid and steam can be blown out
under pressure if plug and cap are taken off too soon.
4) Disconnect IAT sensor at coupler.
5) Remove air cleaner outlet hose (2) with resonator.
6) Disconnect accelerator cable (1) from throttle body.

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-15
7) Disconnect the following electric lead wires and release clamp:

Ground wires (5) from intake manifold

TP sensor (3)

IAC valve (4)

Fuel injectors

EVAP canister purge valve (2)

MAP sensor (6)

EGR valve (1)
8) Disconnect the following hoses:

Brake booster hose (1) from intake manifold

Canister purge hose (3) from EVAP canister purge valve

Engine cooling water (coolant) hose (2) from IAC valve

PCV hose (4)

Breather hose from cylinder head
9) Disconnect fuel feed hose (2) from pipe (1), and disconnect fuel
return hose (3) from fuel pressure regulator.

1. Long bolt
2. Short bolt
6A1-16 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
10) Remove intake manifold rear stiffener (1) and generator adjust
arm reinforcement (2) from intake manifold (3).
11) Remove intake manifold with throttle body from cylinder head,
and then its gasket.
INSTALLATION
Reverse removal procedure for installation noting the followings.

Use new intake manifold gasket.

When installing intake manifold, install clamps securely.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

Adjust accelerator cable play, referring to Section 6E.

Check to ensure that all removed parts are back in place.
Reinstall any necessary parts which have not been reinstalled.

Refill cooling system referring to Section 6B.

Upon completion of installation, turn ignition switch ON but en-
gine OFF and check for fuel leaks.

Finally, start engine and check for engine coolant leaks.

: Tightening Torque
: Do not reuse
1. Exhaust manifold
2. Gasket
3. Cover
4. Heated oxygen sensor
7. Gasket
8. Exhaust No.1 pipe.
21
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-17
EXHAUST MANIFOLD
WARNING:
To avoid danger of being burned, do not service exhaust
system while it is still hot.
Service should be performed after system cools down.
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect heated oxygen sensor coupler.
Release its wire from clamps.
3) Disconnect exhaust No.1 pipe (1) from WU-TWC.
4) Remove WU-TWC stiffener (2) (if equipped).
5) Remove exhaust manifold (1) and its gasket from cylinder head.

(b)
(a)
6A1-18 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
INSTALLATION
1) Install new gaskets to cylinder head.
2) Install exhaust manifold.
Tighten bolts and nuts to specified torque.
Tightening Torque
(a): 32 N
.m (3.2 kg-m, 23.5 lb-ft)
3) Install exhaust manifold cover(s) (1).
4) Connect oxygen sensor coupler (3) and clamp (2) its wire se-
curely.
5) Tighten exhaust No.1 pipe to manifold nuts and exhaust man-
ifold stiffener bolt.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
6) Connect negative cable at battery.
7) Check exhaust system for exhaust gas leakage.

1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Camshaft timing pulley
6. Tensioner bolt
7. Pulley bolt
8. Seal
9. Inside cover seal
10. Inside cover
11. Outside cover seal
12. Outside cover
13. Tensioner stud
14. Damper
1. Water pump pulley
: Tightening Torque
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-19
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Remove right side of engine under cover.
3) Remove power steering pump belt or A / C compressor belt, if
equipped.
4) Disconnect IAT sensor at coupler.
5) Remove air cleaner case with air cleaner outlet hose.
6) Remove power steering hose stay (1) (if equipped).
7) Remove water pump pulley and drive belt.

1.“V” mark on cylinder
head cover
2. Timing mark by “E” on
camshaft timing belt pulley
3. Arrow mark on oil
pump case
4. Punch mark on crankshaft
timing belt pulley
4. Tensioner stud
6. Damper
6
6A1-20 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
8) Lock crankshaft inserting flat end rod or the like (2) between fly-
wheel ring gear and transmission case, after removing clutch
housing (torque converter housing for A / T) lower plate.
With crankshaft locked, remove crankshaft timing belt pulley
bolt (3).
9) Remove crankshaft pulley bolts (1).
10) Remove crankshaft pulley (4).
11) Install crankshaft timing belt pulley bolt temporarily to turn
crankshaft.
12) Release harness clamps.
13) Remove timing belt outside cover.
14) For installation of timing belt, align 4 timing marks as shown in
figure by turning crankshaft.
15) Remove timing belt tensioner (3), tensioner plate (2), tensioner
spring (5) and timing belt (1).