coil SUZUKI SWIFT 2000 1.G SF310 Service Repair Manual

Ignition key
Transponder
code
Immobilizer
Control
Module
ECM
(1)(2)
(3)(4)
1. Coil antenna
2. Immobilizer Control
Module
3. Engine Control Module
(ECM)
4. Ignition key
8G-2 IMMOBILIZER CONTROL SYSTEM
GENERAL DESCRIPTION
The immobilizer control system designed to prevent vehicle burglar consists of following components.

Engine Control Module (ECM)

Immobilizer Control Module

Ignition key (with built-in transponder)

Coil antenna
Operation of this system is as follows.
(1) Each ignition key has its own code (Transponder code) stored in memory. When the ignition switch is turned
ON, Immobilizer Control Module tries to read the Transponder code through the coil antenna installed to the
steering lock assembly.
(2) Immobilizer Control Module compares the Transponder code read in (1) and that registered in Immobilizer Con-
trol Module and checks if they match.
(3) When it is confirmed that two Transponder codes match each other as described above, Immobilizer Control
Module and ECM check if ECM/Immobilizer Control Module codes registered in them respectively match.
(4) Only when it is confirmed that ECM/Immobilizer Control Module codes match, the engine starts running. If
Transponder codes in Step (2) or ECM/Immobilizer Control Module codes in Step (3) do not match, ECM will
stop operation of the injector and the ignitor (i.e., ignition of spark plug).

IMMOBILIZER CONTROL SYSTEM 8G-3
Vehicle without monitor coupler
1. Coil antenna
2. Immobilizer Control Module
3-1. ECM (G10 engine)
3-2. ECM (G13 engine without monitor coupler)
3-3. ECM (G13 engine with monitor coupler)
4. Immobilizer diagnostic coupler
4-1. Diagnostic output terminal
4-2. Ground terminal
5. Malfunction indicator lamp
6. Main relay
7. Ignition switch
8. Fuse
9. Main fuse
10. To #9-pin in Data link connector
11. To #7-pin in Data link connector
12. To ABS control module
13. Immobilizer indicator lamp
(Vehicle not equipped with monitor coupler)
14. Monitor coupler (Vehicle not equipped
with immobilizer indicator lamp)
Vehicle with monitor couplerG10 engineG13 engine
G13B engine
n
W/R
Bl / B
W/Bl
B/W
V/G
W/Bl
B/W
B
V/W
V/W
P/B
P/Bl
P/G
B
B
B/Bl
B/R
–
R/G
–W/R
Gr
R/B
B/W
V/G
W/Bl
B/W
B
Y/B
V/W
P/B
P/Bl
P/G
B
B
B/Or
B/Or
–
R/G
–W/R
G/B
W/Bl
B/W
–
W/Bl
B/W
B
V/W
V/W
P/B
P/Bl
P/G
B
B/Bl
B/Bl
B/G
V
–
V/Y WIRE
SYMBOL
G10 engineG13 engine
without monitor
couplerG13 engine
with monitor
coupler WIRE COLORabcdefghijklmnopqrst

0.5TIME (sec.) Ignition switch ON
High Immobilizer
control system
is normal
Immobilizer
control system
is abnormalLow
0.5 0.5 0.5 0.5
High
Low
8G-4 IMMOBILIZER CONTROL SYSTEM
ON-BOARD DIAGNOSTIC SYSTEM
(SELF-DIAGNOSIS FUNCTION)
Immobilizer Control Module & ECM diagnose troubles which may
occur in the area including the following parts when the ignition
switch is ON.
ECM:
ECM/Immobilizer Immobilizer
Control Module Control
code Module:
Transponder code

Data link connector
Coil antenna
wire
ECM/Immobilizer

ECM Control Module
code

Data link
connector wire

Immobilizer
Control Module

Ignition signal

With the diagnosis switch terminal of monitor coupler for ECM not
grounded, the ignition switch turned ON (but the engine at stop) and
regardless of the condition of the engine and emission control sys-
tem, ECM indicates whether a trouble has occurred in the immobi-
lizer control system or not by causing the malfunction indicator lamp
to flash or turn ON.
Malfunction indicator lamp is ON:
No trouble exists in the immobilizer control system.
Malfunction indicator lamp is flashing:
ECM or Immobilizer Control Module has detected some trouble in
the immobilizer control system.
NOTE:
As soon as the ignition switch is turned ON, ECM and Immobi-
lizer Control Module diagnose if a trouble has occurred in the
immobilizer control system. While the diagnosis is being
made, the malfunction indicator lamp stays ON and if the diag-
nosis result is “abnormal”, it immediately changes to flashing
but if the result is “normal”, it remains ON. Diagnosis takes
about 3 seconds at maximum.

IMMOBILIZER CONTROL SYSTEM 8G-7
[INTERMITTENT TROUBLES]


There are cases where output of diagnostic output terminal
and / or malfunction indicator lamp indicate a diagnostic trouble
code representing a trouble which occurred only temporarily and
has gone. In such case, it may occur that good parts are replaced
unnecessarily. To prevent such accident, be sure to follow instruc-
tions given below when checking by using “Diagnostic Flow
Table”.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and / or malfunction indicator lamp indicate a
trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what malfunction indicator lamp and / or output of diag-
nostic output terminal indicate.
Only when they indicate trouble code again, substitute a known-
good ECM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.


There are cases where output of diagnostic output terminal and /
or Suzuki scan tool indicate a diagnostic trouble code represent-
ing a trouble which occurred only temporarily and has gone. In
such case, it may occur that good parts are replaced unnecessar-
ily. To prevent such accident, be sure to follow instructions given
below when checking by using “Diagnostic Flow Table”.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and / or Suzuki scan tool indicate a trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what Suzuki scan tool and / or output of diagnostic out-
put terminal indicate.
Only when they indicate trouble code again, substitute a known-
good ECM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.

8G-10 IMMOBILIZER CONTROL SYSTEM
1. Immobilizer diagnostic coupler
EXAMPLE :
COIL ANTENNA FAILURE (CODE NO.13)
Voltmeter indicator

NORMAL (No code)
Voltmeter indicatorTIME (sec.)
TIME (sec.) CODE No. 13CODE No. 13CODE No. 13
High
Low
High
Low
1. Monitor coupler
2. Service wire
A: Diagnosis switch
terminal
B: Ground terminal
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
(IMMOBILIZER CONTROL MODULE)
1) Using analog type voltmeter, connect positive probe to diagnos-
tic output terminal and negative probe to ground of immobilizer
diagnostic coupler with ignition switch turned ON.
2) Read deflection of voltmeter indicator which represents DTC as
shown in example below and write it down. For details of DTC,
refer to Immobilizer Control Module side in “Diagnostic Trouble
Code Table”.
If voltmeter indicator dose not deflect, go to “Diagnostic Flow
Table A”.
NOTE:
If abnormality or malfunction lies in two or more areas, volt-
meter indicates applicable codes three times each.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK (ECM)
[Not using SUZUKI scan tool] (Vehicle equipped with
monitor coupler)
1) Using service wire, ground diagnostic switch terminal in monitor
coupler.
2) Read DTC from flashing pattern of malfunction indicator lamp as
shown in example below and write it down. For details of DTC,
refer to ECM side in “Diagnostic Trouble Code Table”.
If lamp remains ON, go to “Malfunction Indicator Lamp Check”
in Section 6.
NOTE:
If abnormality or malfunction lies in two or more areas, mal-
function indicator lamp indicates applicable codes three
times each.
And flashing of these codes is repeated as long as diagno-
sis terminal is grounded and ignition switch is held at ON
position.

8G-12 IMMOBILIZER CONTROL SYSTEM
EXAMPLE:
COIL ANTENNA FAILURE (CODE NO.13)
EXAMPLE:
NORMAL
Voltmeter Indicator
Voltmeter IndicatorHigh
Low
High
LowCODE No. 13 CODE No. 13 CODE No. 13
DIAGNOSTIC TROUBLE CODE TABLE
Immobilizer Control Module
DIAGNOSTIC TROUBLE CODEDIAGNOSTIC AREADIAGNOSISNO.VOLTMETER INDICATIONDIAGNOSTIC AREADIAGNOSIS
–NormalThis code appears when none of the other
codes are identified.
11
Transponder code
31
Transponder code
12Immobilizer Control Module
Di t bl di t
13Coil antenna or ignition key with
built-in transponderDiagnose trouble according to
“DIAGNOSTIC FLOW TABLE”
corresponding to each code No
21ECM / Immobilizer Control
Module code
corres onding to each code No.
22Ignition switch circuit
23Serial data link wire
Engine Control module (ECM)
DTC
(indicated on
Suzuki
scan tool)DTC
(indicated
by MIL)Malfunction Indicator lamp
(MIL) flashing patternDIAGNOSTIC AREADIAGNOSIS
NO DTC12Normal
This code appears when it is
confirmed that none of other
trouble codes is set for
immobilizer control system or
engine and emission control
system.
P162381ECM / Immobilizer
P162084Control Module codeDiagnose trouble according to
“DIAGNOSTIC FLOW TABLE”
P162282ECMcorresponding to each code
No.
P162183Serial data link wire