check oil SUZUKI SWIFT 2000 1.G SF310 Service Manual Online

1. Ignition switch
2. Main relay
3. Ignition coil assembly
for No.1 and No.4
spark plugs
4. Ignition coil assembly
for No.2 and No.3
spark plugs5. CMP sensor
6. CKP sensor
7. No.1 spark plug
8. No.2 spark plug
9. No.3 spark plug
10. No.4 spark plug11. Sensed information

MAP sensor

ECT sensor

IAT sensor

TP sensor

VSS
Park / Neutral position signal
(A / T)

Electric load signal

Engine start signal
IGNITION SYSTEM (SFI FOR G13) 6F1-3
SYSTEM WIRING DIAGRAM
DIAGNOSIS
ConditionPossible CauseCorrection
Engine cranks, but will
not start or hard to
startNo spark

Blown fuse for ignition coil

Loose connection or disconnection of lead
wire or high-tension cord(s)

Faulty high-tension cord(s)

Faulty spark plug(s)

Faulty ignition coil

Faulty CKP sensor or crankshaft timing belt
pulley

Faulty ECM (PCM)
Replace.
Connect securely.
Replace.
Adjust, clean or replace.
Replace ignition coil assembly.
Clean, tighten or replace.
Replace.
Poor fuel economy or
engine performance
Incorrect ignition timing

Faulty spark plug(s) or high-tension cord(s)

Faulty ignition coil assembly

Faulty CKP sensor or crankshaft timing belt
pulley

Faulty ECM (PCM)Check related sensors and
crankshaft timing belt pulley.
Adjust, clean or replace.
Replace.
Clean, tighten or replace.
Replace.

6F1-4 IGNITION SYSTEM (SFI FOR G13)
IGNITION SYSTEM DIAGNOSTIC FLOW TABLE
STEPACTIONYESNO
1
Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE” in
section 6.
2
Ignition Spark Test
1) Check all spark plugs for condition and type
referring to “Spark Plugs” section.
2) If OK, perform ignition spark test, referring to
“Ignition Spark Test” section.
Is spark emitted from all spark plugs?Go to Step 11.Go to Step 3.
3
Diagnostic Trouble Code (DTC) Check
Is DTC stored in ECM (PCM)?Go to applicable DTC
Diag. Flow Table in
section 6.Go to Step 4.
4
Electrical Connection Check
1) Check ignition coil assemblies and high-tension
cords for electrical connection.
Are they connected securely?Go to Step 5.Connect securely.
5
High-Tension Cords Check
1) Check high-tension cord for resistance referring
to “High-Tension Cords” section.
Is check result satisfactory?Go to Step 6.Replace high-tension
cord(s).
6
Ignition Coil Assembly Power Supply and Ground
Circuit Check
1) Check ignition coil assembly power supply and
ground circuits for open and short.
Are circuits in good condition?Go to Step 7.Repair or replace.
7
Ignition Coil Assembly Check
1) Check ignition coil for resistance referring to
“Ignition Coil Assembly” section.
Is check result satisfactory?Go to Step 8.Replace ignition coil
assembly.
8
Crankshaft Position (CKP) Sensor Check
1) Check crankshaft position sensor referring to
Step 3 and 4 of DTC P0335 Diag. Flow Table in
section 6.
Is check result satisfactory?Go to Step 9.Tighten CKP sensor
bolt, replace CKP
sensor or crankshaft
timing belt pulley.
9
Ignition Trigger Signal Circuit Check
1) Check ignition trigger signal wire for open, short
and poor connection.
Is circuit in good condition?Go to Step 10.Repair or replace.
10
A Known-good Ignition Coil Assembly Substitution
1) Substitute a known-good ignition coil assembly
and then repeat Step 2.
Is check result of Step 2 satisfactory?Go to Step 11.Substitute a known-
good ECM (PCM) and
then repeat Step 2.
11
Ignition Timing Check
1) Check initial ignition timing and ignition timing
advance referring to “Ignition Timing” section.
Is check result satisfactory?System is in good
condition.Check CKP sensor,
crankshaft timing belt
pulley (signal rotor)
and input signals
related to this system.

IGNITION SYSTEM (SFI FOR G13) 6F1-5
ON-VEHICLE SERVICE
IGNITION SPARK TEST
1) Disconnect all injector couplers (1) from injectors (2).
WARNING:
Without disconnection of injector couplers, combustible
gas may come out from spark plug holes during this test
and may get ignited in engine room.
2) Remove spark plug and check it for condition and type referring
to “Spark Plugs” in this section.
3) If OK, connect ignition coil coupler to ignition coil assembly and
connect spark plug to ignition coil assembly or high-tension
cord. Ground spark plug.
4) Crank engine and check if each spark plug sparks.
5) If no spark is emitted, inspect the related parts as described un-
der “Diagnosis” earlier in this section.
HIGH-TENSION CORDS
1) Disconnect high-tension cords (1) from ignition coil assemblies
(2) while gripping each cap.
2) Pull out high-tension cords from spark plugs while gripping each
cap.
CAUTION:
Pull out each connection by gripping cap portion so as
not to damage their inside wire (resistive conductor).
3) Measure resistance of high-tension cord (1) by using ohmmeter.
High-tension cord resistance: 4 – 10 kΩ/ m (1.2 – 3.0 kΩ/ ft)
4) If resistance exceeds specification, replace high-tension
cord(s).

IGNITION SYSTEM (SFI FOR G13) 6F1-7
5) Measure secondary coil for resistance.
Secondary coil resistance : 7.6 – 10.2 kΩ at 20C, 68F
If resistance is out of specification, replace ignition coil assem-
bly.
6) Install ignition coil assembly.
7) Tighten ignition coil bolts, and then connect ignition coil coupler.
8) Install high-tension cord to ignition coil assembly while gripping
its cap.
CRANKSHAFT POSITION SENSOR
(CKP SENSOR)
Refer to section 6E2 for removal, inspection and installation.
IGNITION TIMING
NOTE:

Ignition timing is not adjustable. If ignition timing is out of
specification, check system related parts.

Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T model),
and set parking brake.
INSPECTION
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
2) Start engine and warm it up to normal operating temperature.
3) Make sure that all of electrical loads except ignition are switched
off.
4) Check to be sure that idle speed is within specification.
(Refer to SECTION 6E2)

7B-18 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

A / T fluid– – – – – level, leakage, color

A / T fluid hoses – – – – – disconnection, looseness, deterioration

Throttle cable – – – – – play, installation

A / T oil pressure control cable and select cable – – – – – installation

Engine oil – – – – – level, leakage

Engine coolant – – – – – level, leakage

Battery – – – – – fluid level, corrosion of terminal

Connectors of electric wire harness – – – – – disconnection, friction

Fuses – – – – – burning

Parts – – – – – installation, bolt – – – – – looseness

Parts – – – – – deformation

Other parts that can be checked visually
Also check following items at engine start, if possible.

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Other parts that can be checked visuallySection 0B
Section 7B
Section 6E1 or 6E2
Section 7B
Section 0B
Section 0B
Section 6 or 6-1
Section 8
Section 6 or 6-1
Section 6H
Section 8 (Section 6A or 6A1 for
pressure check)

ACCEPTABLE RANGE
1st gear (solenoids ON and ON)
2nd gear
(solenoids ON and OFF)
3rd gear
(solenoids OFF and OFF)
Vehicle speed
Engine speed
7B-28 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0751 SHIFT SOLENOID-A (No.1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID-B (No.2) PERFORMANCE OR STUCK OFF
CIRCUIT DESCRIPTION
PCM monitors throttle opening, engine speed, vehicle speed and gear position and compares the actual engine
speed and its specified value (i.e., engine speed obtained by PCM through calculation using the throttle open-
ing / gear position and vehicle speed).
DTC DETECTING CONDITION
POSSIBLE CAUSE

While running in “D” range after engine warmed up,
engine speed as compared with vehicle speed is not
within acceptable range.
2 driving cycle detection logic, continuous
monitoring.
A / T oil pressure control cable maladjusted

Selector cable maladjusted

Mechanical malfunction of shift solenoid valve
(stick or leakage)

Mechanical malfunction in transmission

Torque converter malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON and warm up engine to normal operating temperature.
3) Shift selector lever to “D” range.
4) Start vehicle and increase vehicle speed to 40 – 55 km / h ( 25 – 35 mile / h) by depressing accelerator pedal half
a stroke.
5) Keep vehicle at above speed for 5 sec. or longer.
6) Increase vehicle speed to 75 – 90 km / h (45 – 55 mile / h) by depressing accelerator pedal half a stroke and keep
it at that speed for 5 sec. or longer.
7) Stop vehicle and check pending DTC and DTC.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-31
TABLE A-2 GEAR CHANGE FAILURE
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to “AUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLE”.
2Disconnect solenoid valve wire coupler and perform
manual road test.
Is upshift from 1st to 2nd possible?Go to Step 3.1-2 shift valve sticks
or Shift solenoid-B
(2nd brake solenoid)
valve sticks.
3Is upshift from 2nd to 3rd possible?Gear shift control
system defective.
Go to A / T Diagnostic
Flow Table B.2-3 shift valve sticks
or Shift solenoid-A
(Direct clutch
solenoid) valve
sticks.
TABLE A-3 EXCESSIVE SHOCK AT RANGE SELECTION OR GEAR CHANGE
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to “AUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLE”.
2Is line pressure proper?Go to Step 3.Regulator valve
defective, Throttle
valve defective or
Accelerator cable
maladjusted.
3Does excessive shock occur when selecting “D” range
from “N” range?Forward clutch
accumulator
operation failure,
Forward clutch worn
or Forward clutch oil
circuit check ball
operation failure. Go to Step 4.
4Does excessive shock occur when selecting “R” range
from “N” range?1st-Reverse brake
worn, 1st-Reverse
brake oil circuit check
ball operation failure.Go to Step 5.
5Does excessive shock occur at 1st to 2nd gear
change?2nd brake
accumulator
defective, 2nd brake
worn, 2nd brake oil
circuit check ball
operation failure.In case of excessive
shock at 2nd to 3rd
gear change, Direct
clutch worn or Direct
clutch oil circuit check
ball operation failure.

7B-32 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at D and R ranges.
Be sure to perform this test only when transmission fluid is at normal
operating temperature (70–80C / 158–176F) and its level is be-
tween FULL HOT and LOW HOT. (Refer to “Fluid level” in this sec-
tion.)
CAUTION:
Do not run engine at stall more than 5 seconds continuous-
ly, for oil temperature may rise excessively high.
1) Install tachometer.
2) Apply parking brake and block vehicle wheels.
3) Start engine with selector lever shifted to P range.
4) Depress brake pedal.
5) Shift selector lever to D range and depress accelerator pedal ful-
ly while watching tachometer. Read engine rpm quickly when it
has become constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed at R range.
8) Stall speed should be within following specification.
Stall speed: 2,500 – 2,900 r / min
(For both G10 and G13 engine models)
9) Possible causes for out-of-specification stall speed are as fol-
lows. Check each part which is suspected to be the cause.
Stall speed measured
Possible causes
Lower than specification
Engine output insufficient

Torque converter defective
Higher than specification in
D range
Forward clutch slippage

One-way clutch defective
Higher than specification in
R range
Direct clutch slippage

1st-reverse brake slippage

1. Front drive shaft (LH)
2. Oil pan
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-33
LINE PRESSURE TEST
This test is to check oil pressure system for operation by measuring
oil pressure in oil pressure line. Make sure to perform this test only
when transmission fluid is at normal operating temperature.
NOTE:

Make sure that transmission fluid level is between FULL HOT
and LOW HOT marks on oil level gauge at normal operating
temperature which corresponds to 70–80C (155–176F) of
fluid. (Refer to “Fluid level” in this section.)

Check that transmission is free from fluid leakage.
1) With engine at stop, remove plug and connect oil pressure
gauge to plug hole.
Special Tool
(A): 09925-37811-001
2) Install tachometer.
3) Apply parking brake and block vehicle wheels.
4) With selector lever shifted to P range, start engine.
5) Depress brake pedal fully.
6) Shift selector lever to D range and check oil pressure with engine
running at idling speed and at stall speed respectively.
7) Repeat the same check as in step 6) with selector lever shifted
to R range.
CAUTION:
Do not run engine at stall more than 5 seconds continu-
ously, for oil temperature may rise excessively high.
8) If line pressure is within respective specification in table below,
oil pressure system is in good condition.
[G10 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
200 – 390 kPa
2.0 – 3.9 kg / cm2
28.4 – 55.5 psi
540 – 780 kPa
5.4 – 7.8 kg / cm2
76.8 – 110.9 psi
Stall speed
390 – 590 kPa
3.9 – 5.9 kg / cm2
55.5 – 83.9 psi
880 – 1230 kPa
8.8 – 12.3 kg / cm2
125.1 – 174.9 psi
[G13 Engine Model]
Engine speedLine pressureEngine s eedD rangeR range
Idling speed
260 – 460 kPa
2.6 – 4.6 kg / cm2
37.0 – 65.4 psi
660 – 900 kPa
6.6 – 9.0 kg / cm2
93.9 – 128.0 psi
Stall speed
660 – 850 kPa
6.6 – 8.5 kg / cm2
93.9 – 120.9 psi
1330 kPa or more
13.3 kg / cm2 or more
189.0 psi or more

1. Drive shaft (LH)
2. Oil pan
7B-34 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
9) Possible causes for out-of-specification line pressure are as
follows. Check each part which is suspected to be the cause.
Line pressure
Possible causes
Higher than specification
in D and R ranges
Regulator valve defective

Throttle valve in valve body
defective

Accelerator cable and oil
pressure control cable
maladjusted
Lower than specification
in D and R ranges
Oil pump defective

Regulator valve defective

Throttle valve in valve body
defective

Accelerator cable and oil
pressure control cable
maladjusted
Lower than specification
only in D range
Forward clutch oil pressure
system oil leakage

D range oil pressure system
oil leakage
Lower than specification
only in R range
Direct clutch oil pressure
system oil leakage

1st-reverse brake oil
pressure system oil leakage

R range oil pressure system
oil leakage
10) Reinstall plug and tighten it to specification.
Tightening Torque
(a): 7.5 N·m (0.75 kg-m, 5.5 lb-ft)