Fluid SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

0A-22 GENERAL INFORMATION
A
ABS : Anti-Lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency Locking
Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector (Assembly
Line Diag. Link, ALDL, Serial
Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control Module
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp. Sensor,
WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust
Gas Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation Heater
(Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission Canister
(Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid Valve,
ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature Sensor
(Air temperature Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL
ABBREVIATIONS

G (Base Color)
G (Base Color)
Y (Stripe Color)
0A-24 GENERAL INFORMATION
SYMBOLS
SYMBOLDEFINITIONSYMBOLDEFINITION
Tightening torqueApply SUZUKI BOND NO. 1216
99000-31160
Apply oil (Engine, transmission,
transfer, differential)Apply SILICONE SEALANT
99000-31120
Apply fluid (Brake, power steering or
automatic transmission fluid)Apply SEALING COMPOUND 366E
99000-31090
Apply SUZUKI SUPER GREASE A
99000-25010
Apply SUZUKI SUPER GREASE C
99000-25030Apply THREAD LOCK 1322
99000-32110
Apply SUZUKI SUPER GREASE E
99000-25050Apply THREAD LOCK 1333B
99000-32020
Apply SUZUKI SUPER GREASE H
99000-25120Apply THREAD LOCK 1342
99000-32050
Apply SUZUKI SUPER GREASE I
99000-25210
Apply SUZUKI BOND NO. 1215
99000-31110Do not reuse
Apply SUZUKI BOND NO. 1207C
99000-31150Note on reassembly
WIRE COLOR SYMBOLS
SymbolWire ColorSymbolWire Color
BBLKBlackO, OrORNOrange
BlBLUBlueRREDRed
BrBRNBrownWWHTWhite
GGRNGreenYYELYellow
GrGRYGrayPPNKPink
LblLT BLULight blueVPPLViolet
LgLT GRNLight green
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. “G”).
The dual-colored wire uses two color symbols (i.e. “G/Y”). The first
symbol represents the base color of the wire (“G” in the figure) and
the second symbol represents the color of the stripe (“Y” in the fig-
ure).

0B
MAINTENANCE AND LUBRICATION 0B-1
SECTION 0B
MAINTENANCE AND LUBRICATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
MAINTENANCE SCHEDULE0B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Condition Schedule0B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Recommended Under Severe Driving Conditions 0B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE0B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine0B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition System0B-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel System0B-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emission Control System0B-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake0B-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis and Body0B-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Inspection0B-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RECOMMENDED FLUIDS AND LUBRICANTS0B-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km (54,000 miles)
mileage. Beyond 90,000 km (54,000 miles), carry out the same services at
the same intervals respectively.
This interval should be judged by
odometer reading or months,Km(
1,000)153045607590g
whichever comes first.Miles(
1,000)91827364554
Months122436486072
4. EMISSION CONTROL SYSTEM
4-1.PCV (Positive Crankcase Ventilation)
ValveVehicle
without
O2S
––I––I
Vehicle
with O2S–––––I
4-2.Fuel evaporative emission control system–––––I
5. BRAKE
5-1.Brake discs and padsIIIIII
Brake drums and shoes–I–I–I
5-2.Brake hoses and pipes–I–I–I
5-3.Brake fluid–R–R–R
5-4.Brake lever and cableInspect at first 15,000 km (9,000 miles) only.
6. CHASSIS AND BODY
6-1.Clutch pedal (for manual transmission)–I–I–I
6-2.Tires/wheel discsIIIIII
6-3.Propeller shaft (4WD) and drive shafts––I––I
6-4.Suspension system–I–I–I
6-5.Steering system–I–I–I
6-6.Power steering (if equipped)IIIIII
6-7.Manual transmission oilI–R––R
6-8.Automatic transmissionFluid level–I–I–I
Fluid changeReplace every 165,000 km (99,000 miles).
Fluid hose–––R––
6-9.Rear differential oil (4WD) (R: 1st 15,000 km only)R or I–I–I–
6-10. All latches, hinges and locks–I–I–I
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

0B-4 MAINTENANCE AND LUBRICATION
MAINTENANCE RECOMMENDED UNDER SEVERE DRIVING CONDITIONS
If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is
recommended that applicable maintenance operation be performed at the particular interval as given in the chart
below.
Severe condition code
A –Repeated short trips F –Leaded fuel use
B –Driving on rough and/or muddy roads G –(For Diesel engine) Town use / Towing a trailer /
C –Driving on dusty roads Sustained high speed driving /
D –Driving in extremely cold weather and/or Hot climates above 30C (86F) /
salted roads Low quality lubricants or fuel
E –Repeated short trips in extremely cold weather H –Trailer towing (if admitted)
Severe
Condition Code
MaintenanceMaintenance
OperationMaintenance Interval
BCDITEM 1-1IEvery 15,000 km (9,000 miles)
or 12 months
– B C D – – – –Drive belt (V-rib belt)REvery 45,000 km (27,000 miles)
or 36 months
A – C D E F – HITEM 1-4
Engine oil and filterREvery 5,000 km (3,000 miles)
or 4 months
A B C – E F – HITEM 2-1
Spark plugsREvery 10,000 km (6,000 miles)
or 8 months
ITEM 3 1IEvery 2,500 km (1,500 miles)
– – C – – – – –ITEM 3-1
Air cleaner filter *1REvery 30,000 km (18,000 miles)
or 24 months
– B C D – – – HITEM 6-2
Wheel bearingsIEvery 15,000 km (9,000 miles)
or 12 months
– B – D E – – H
ITEM 6-3
Propeller shaft (4WD) and drive
shafts
I
Every 15,000 km (9,000 miles)
or 12 months
– B – – E – – H
ITEM 6-7 / 6-8
Manual transmission oil and
differential oil (4WD)
R
Every 30,000 km (18,000 miles)
or 24 months
– B – – E – – HITEM 6-9
Automatic transmission fluidREvery 30,000 km (18,000 miles)
or 24 months
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

*1: Inspect or replace more frequently if necessary

1. Full level mark (hole)
2. Low level mark (hole)
Oil pan capacity
Oil filter capacity
Others
Total1.0 L and 1.3 L Engine
About 3.1 liters
(6.5 / 5.5 US / lmp pt.)
About 0.2 liter
(0.4 / 0.3 US / lmp pt.)
About 0.3 liter
(0.6 / 0.5 US / lmp pt.)
About 3.6 liters
(7.5 / 6.3 US / lmp pt.)
0B-8 MAINTENANCE AND LUBRICATION
7) Replenish oil until oil level is brought to FULL level mark on dip-
stick (oil pan and oil filter capacity). Filler inlet is at the top of cyl-
inder head cover.
8) Start engine and run it for three minutes. Stop it and wait another
5 minutes before checking oil level. Add oil, as necessary, to
bring oil level to FULL level mark on dipstick.
Engine Oil Capacity
NOTE:
Engine oil capacity is specified as left table.
However, note that amount of oil required when actually
changing oil may somewhat differ from data in left table de-
pending on various conditions (temperature, viscosity, etc.).
9) Check oil filter and drain plug for oil leakage.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
CAUTION:
When changing engine coolant, use mixture of 50% water
and 50% ethylene-glycol base coolant (Anti-Freeze/Anti-
corrosion coolant) for the market where ambient tempera-
ture falls lower than –16C (3F) in winter and mixture of
70% water and 30% ethylene-glycol base coolant for the
market where ambient temperature doesn’t fall lower than
–16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ethylene-glycol base
coolant should be used for the purpose of corrosion protec-
tion and lubrication.
Refer to SECTION 6B for COOLANT CAPACITY.

MAINTENANCE AND LUBRICATION 0B-13
ITEM 5-2
Brake Hoses and Pipes Inspection
Perform this inspection where there is enough light and use a mirror
as necessary.

Check brake hoses and pipes for proper hook-up, leaks, cracks,
chafing, wear, corrosion, bends, twists and other damage.
Replace any of these parts as necessary.

Check all clamps for tightness and connections for leakage.

Check that hoses and pipes are clear of sharp edges, moving
parts.
CAUTION:
After replacing any brake pipe or hose, be sure to carry out
air purge operation.
ITEM 5-3
Brake Fluid Change
CAUTION:
Since brake system of this vehicle is factory-filled with
brake fluid indicated on reservoir cap, do not use or mix dif-
ferent type of fluid when refilling; otherwise serious dam-
age will occur.
Do not use old or used brake fluid, or any fluid from a un-
sealed container.
Change brake fluid as follows.
Drain existing fluid from brake system completely, fill system with
specified fluid and carry out air purge operation.
For air purging procedure, refer to SECTION 5.

1. Ball joint stud dust seal (boot)
2. Suspension arm
1. Tie-rod end boot
2. Steering gear case boot
3. Universal joint
0B-16 MAINTENANCE AND LUBRICATION

Check front and rear suspension systems for damaged, loose or
missing parts; also for parts showing signs of wear or lack of lu-
brication.
Repair or replace defective parts, if any.

Check front suspension arm ball joint stud dust seals for leakage,
detachment, tear or any other damage.
Replace defective boot, if any.
ITEM 6-5
Steering System Inspection
1) Check steering wheel for play and rattle, holding vehicle straight
on ground.
Steering wheel play “a”: 0 – 30 mm (0 – 1.1 in.)
2) Check steering linkage for looseness and damage. Repair or re-
place defective parts, if any.
3) Check boots of steering linkage and steering gear case for dam-
age (leaks, detachment, tear, etc.). If damage is found, replace
defective boot with new one.
4) Check universal joints of steering shaft for rattle and damage. If
rattle or damage is found, replace defective part with a new one.
ITEM 6-6
Power Steering (P / S) System Inspection (if equipped)
1) Visually check power steering system for fluid leakage and hose
for damage and deterioration.
Repair or replace defective parts, if any.
2) With engine stopped, check fluid level indicated on fluid tank,
which should be between MAX and MIN marks. If it is lower than
MIN, fill fluid up to MAX mark.
NOTE

Be sure to use specified P / S fluid.

Fluid level should be checked when fluid is cool.
3) Visually check pump drive belt for cracks and wear.
4) Check belt for tension, referring to item 1-1 in this section.
If necessary, adjust or replace.

1. Oil level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
1. Drain plug
0B-18 MAINTENANCE AND LUBRICATION
ITEM 6-9
Automatic Transmission
[Fluid level inspection]
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B and be sure to perform it under specified
conditions. If fluid level is low, replenish specified fluid.
[Fluid change]
1) Perform steps 1) and 2) of above Fluid Level Inspection.
2) Change fluid. For its procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B.
CAUTION:
Use of specified fluid is absolutely necessary.
[Fluid cooler hose change]
Replace inlet and outlet hoses (1) of cooler hose and their clamps.
For replacement procedure, refer to ON-VEHICLE SERVICE in
SECTION 7B.

MAINTENANCE AND LUBRICATION 0B-21
[Parking brake]
Check that lever has proper travel.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to “HI” position and mode lever to
defroster position for this check. WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSE, SF, SG, SH or SJ (Refer to engine oil viscosity chart in item 1-4.)
Engine coolantEthylene-glycol base coolant (“Antifreeze / Anticorrosion coolant”)
Brake fluidDOT3
Manual transmission oilSee SECTION 7A
Rear differential oilSee SECTION 7E
Automatic transmission fluidAn equivalent of DEXRON-IIE or DEXRON-III
Power steering fluidSee material table on SECTION 3B1
Door hingesEngine oil
Engine hood latchEngine oil
Key lock cylinderSpray lubricant