Motor SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

()x()x()x()x()x()x()x()x()x
()x()x()x()x()x()x()x()x()x
FOREWORD
This SUPPLEMENTARY SERVICE MANUAL is a supplement to SF SERIES SERVICE MANU-
ALS mentioned in next page and has been prepared exclusively for the following applicable mod-
el.
Applicable model: SF310 / SF413 of and after the vehicle identification numbers below.
Vehicle Identification Number (Vehicle Specification)
TSMMAA44S00600001 (SF310 3 door H / B 2WD)
TSMMAB44S00600001 (SF310 5 door H / B 2WD)
TSMMAA35S00600001 (SF413 3 door H / B 2WD)
TSMMAB35S00600001 (SF413 5 door H / B 2WD)
TSMMAB35S10600001 (SF413 5 door H / B 2WD)
TSMMSF35S00600001 (SF413 3 door H / B 4WD)
TSMMSG35S00600001 (SF413 5 door H / B 4WD)
TSMMAH35S00600001 (SF413 4 door N / B 2WD)
TSMMAH35S10600001 (SF413 4 door N / B 2WD)
When servicing the above applicable models, refer to this SUPPLEMENTARY SERVICE MANU-
AL first. If necessary information is not found in this SUPPLEMENTARY SERVICE MANUAL, re-
fer to RELATED MANUALS specified next page.
All information, illustrations and specifications contained in this literature are based on the latest
product information available at the time of publication approval. And used as the main subject
of description is the vehicle of standard specifications among others. Therefore, note that illustra-
tions may differ from the vehicle being actually serviced.
The right is reserved to make changes at any time without notice.
OVERSEAS SERVICE DEPARTMENT
 COPYRIGHT SUZUKI MOTOR CORPORATION 2000

0A-22 GENERAL INFORMATION
A
ABS : Anti-Lock Brake System
ATDC : After Top Dead Center
API : American Petroleum Institute
ATF : Automatic Transmission Fluid
ALR : Automatic Locking Retractor
AC : Alternating Current
A / T : Automatic Transmission
A / C : Air Conditioning
ABDC : After Bottom Dead Center
A / F : Air Fuel Mixture Ratio
A-ELR : Automatic-Emergency Locking
Retractor
B
B+ : Battery Positive Voltage
BTDC : Before Top Dead Center
BBDC : Before Bottom Dead Center
C
CKT : Circuit
CMP Sensor : Camshaft Position Sensor
(Crank Angle Sensor, CAS)
CO : Carbon Monoxide
CPP Switch : Clutch Pedal Position Switch
(Clutch Switch, Clutch Start
Switch)
CPU : Central Processing Unit
CRS : Child Restraint System
D
DC : Direct Current
DLC : Data Link Connector (Assembly
Line Diag. Link, ALDL, Serial
Data Link, SDL)
DOHC : Double Over Head Camshaft
DOJ : Double Offset Joint
DRL : Daytime Running Light
DTC : Diagnostic Trouble Code
(Diagnostic Code)
E
EBCM : Electronic Brake Control
Module, ABS Control Module
ECM : Engine Control Module
ECT Sensor : Engine Coolant Temperature
Sensor (Water Temp. Sensor,
WTS)
EGR : Exhaust Gas Recirculation
EGRT Sensor : EGR Temperature Sensor
(Recirculated Exhaust
Gas Temp. Sensor, REGTS)
EFE Heater : Early Fuel Evaporation Heater
(Positive Temperature
Coefficient, PTC Heater)
ELR : Emergency Locking Retractor
EPS : Electronic Power Steering
EVAP : Evaporative Emission
EVAP Canister : Evaporative Emission Canister
(Charcoal Canister)
F
4WD : 4 Wheel Drive
G
GEN : Generator
GND : Ground
H
HC : Hydrocarbons
HO2S : Heated Oxygen Sensor
I
IAC Valve : Idle Air Control Valve (Idle
Speed Control Solenoid Valve,
ISC Solenoid Valve)
IAT Sensor : Intake Air Temperature Sensor
(Air temperature Sensor, ATS)
ICM : Immobilizer Control Module
IG : Ignition
ISC Actuator : Idle Speed Control Actuator
(Motor)
ABBREVIATIONS AND SYMBOLS MAY BE USED IN THIS MANUAL
ABBREVIATIONS

6-80 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 1
Main
fuseIgnition switch“IG COIL METER”
Radiator fan
relay
Radiator fan motor
DTC P0480 RADIATOR FAN CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low voltage at terminal C02-20 when engine coolant
temp. is below 91C, 195F.
2 driving cycle detection logic, continuous monitoring.
“B/W” or “BI” circuit open or short

Radiator fan relay malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Warm up engine until radiator cooling fan starts to operate.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.

6-88 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 2 Fig. 2 for Step 3
Lever is apart
from plunger
Lever contacts
with plunger Condition “A”:
throttle lever is in contact
with ISC actuator plunger
Condition “B”:
Throttle lever is apart
from plunger
DTC P0510 CLOSED THROTTLE POSITION (CTP) SWITCH MALFUNCTION
CIRCUIT DESCRIPTION – Refer to DTC P0505 section.
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Even when vehicle is started from stop and
accelerated to specified vehicle speed, CTP switch
does not turn from ON to OFF (or from OFF to ON).
2 driving cycle detection logic, continuous
monitoring
“Lg”, “Gr / G” or “B/Bl” circuit open or short

CTP switch malfunction

ECM (PCM) malfunction
NOTE:
When DTC P0105, P0120 and / or P0510 are indicated together, it is possible that “Lg” circuit is open.
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF, clear DTC with ignition switch ON and start engine.
2) Increase vehicle speed to 20 mph, 32 km / h and then stop vehicle.
3) Repeat above step 2) 15 times.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check CTP Switch Operation.
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON.
Does CTP switch operate properly under following
conditions respectively?
Condition “A”: ON displayed on scan tool
Condition “B”: OFF displayed on scan tool
Is test result satisfactory?Intermittent trouble.
Check for intermittent
referring to
“Intermittent and
Poor Connection in
Section 0A.Go to Step 3.
3Check CTP switch.
1) Arrange 3 new 1.5 V batteries in series (4.5 V in
total).
2) Connect these batteries to CTP switch terminals
“4” and “5”.
3) Under following each condition, check voltage
between CTP switch terminals “6” and “5”.
Condition “A”: 0 – 1 V
Condition “B”: 3.5 – 5.5 V
Is measured voltage as specified?Check “Lg”, “Gr / G”
and “B/Bl” wires and
connections for open
or short.
If wires and
connections are OK,
substitute a known-
good ECM (PCM) and
recheck.Replace ISC motor
set (throttle lower
body with ISC
actuator).

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-35
CONNECTOR “C02”
TERMINAL
NO.CIRCUITNORMAL
VOLTAGECONDITION
1A / C ON output signal0 VIgnition switch ON
2EGR valve (stepper motor10 – 14 VIgnition switch ON2coil 1)0 – 1 VEngine running at idle speed
3Data link connector10 – 14 VIgnition switch ON
4Heater of HO2S-210 – 14 VIgnition switch ON
5Power source10 – 14 VIgnition switch ON
6Power source10 – 14 VIgnition switch ON
7Power source for buck-up10 – 14 VIgnition switch ON and OFF
8EGR valve (stepper motor10 – 14 VIgnition switch ON8coil 3)10 – 14 VEngine running at idle speed
9EGR valve (stepper motor10 – 14 VIgnition switch ON9coil 2)10 – 14 VEngine running at idle speed
10Main relay10 – 14 VIgnition switch OFF10Main relay0.4 – 1.5 VIgnition switch ON
112-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at 2-range
12N-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at N-range
13Heated oxygen sensor-2Refer to DTC P0130 diag. flow table
14D-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at D-range
15R-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at R-range
16A/C input signal
10 – 14 VIgnition switch ON
A / C switch OFF
16A/C in ut signal
0 – 2 VIgnition switch ON
A / C switch ON
17EGR valve (stepper motor10 – 14 VIgnition switch ON17coil 4)0 – 1 VEngine running at idle speed
18Radiator fan control relay
10 – 14 V
Ignition switch ON
Engine coolant temp.: Below 92.5C
(199F)
18Radiator fan control relay
0 – 1 V
Ignition switch ON
Engine coolant temp.: Below 97.5C
(208F) or higher
19Fuelpumprelay0 – 1 VFor 2 seconds after ignition switch ON19Fuel um relay10 – 14 VAfter the above time
20Blank——
21P-range signal (A / T)
Indication
deflection
repeated
0 V and
10 – 14 V
Ignition switch ON
22Fuel level sensor (gauge)
0 – 2 VIgnition switch ON
Fuel tank fully filled
22Fuel level sensor (gauge)
4.5 – 7.5 VIgnition switch ON
Fuel tank emptied
23L-range signal (A / T)10 – 14 VIgnition switch ON, Select lever at L-range
24Blank——

1 2
1. ECM (PCM) coupler disconnected
2. Ohmmeter
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-37
Resistance Check
1) Disconnect ECM (PCM) couplers from ECM (PCM) with ignition
switch OFF.
CAUTION:
Never touch terminals of ECM (PCM) itself or connect
voltmeter or ohmmeter.
2) Check resistance between each terminal of couplers discon-
nected.
CAUTION:

Be sure to connect ohmmeter probe from wire harness
side of coupler.

Be sure to turn OFF ignition switch for this check.

Resistance in table below represents that when parts
temperature is 20C (68F).
TERMINALSCIRCUITSTANDARD RESISTANCE
C01-7 to C03-6HO2S-1 heater11.7 – 15.6 Ω
C02-4 to C03-6HO2S-2 heater11.7 – 15.6 Ω
C01-9 to C02-5 / 6No.1 injector12.0 – 13.0 Ω
C01-21 to C02-5 / 6No.2 injector12.0 – 13.0 Ω
C01-31 to C02-5 / 6No.3 injector12.0 – 13.0 Ω
C01-8 to C02-5 / 6No.4 injector12.0 – 13.0 Ω
C02-2 to C02-5 / 6EGR valve (stepper motor coil 4)20 – 24 Ω
C02-9 to C02-5 / 6EGR valve (stepper motor coil 3)20 – 24 Ω
C02-8 to C02-5 / 6EGR valve (stepper motor coil 2)20 – 24 Ω
C02-17 to C02-5 / 6EGR valve (stepper motor coil 1)20 – 24 Ω
C01-4 to C02-5 / 6EVAP canister purge valve30 – 34 Ω
C02-19 to C03-6Fuel pump relay70 – 110 Ω
C02-1 to Body groundA / C control moduleNo continuity
C02-18 to C02-5 / 6Radiator fan control relay70 – 110 Ω
C02-10 to C02-7Main relay70 – 110 Ω
C01-1 to Body groundGroundContinuity
C01-2 to Body groundGroundContinuity
C01-3 to Body groundGroundContinuity

INFORMATION SENSORS
-1. MAP sensor
-2. TP sensor
-3. IAT sensor
-4. ECT sensor
-5. Heated oxygen sensor-1
5-1. Heated oxygen sensor-2
-6. VSS (A / T)
-7. Transmission range switch (A / T)
-8. Battery
-9. CMP sensor
-10. CKP sensor
-11. Fuel level sensor (gauge) (in fuel tank)
-12. PSP switch
-13. A / C control module (if equipped)
-14. VSS (speedometer) (M / T)OTHERS
A: ECM (PCM)
B: Main relay
C: EVAP canister
D: Data link connector CONTROL DEVICES
a: Fuel injector
b: EVAP canister purge valve
c: Fuel pump relay
d: EGR valve (step motor)
e: Malfunction indicator lamp
f: Ignition coil assembly
g: Radiator fan control relay
h: IAC valve
6-1-38 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
COMPONENT LOCATION

6-1-74 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
INSPECTION
NOTE:
If starter circuit is open (i.e., start signal circuit is OK but starter fails to run), this DTC is stored in memory
at starter switch ON, even though CKP sensor is in good condition.
When starter motor fails to run and this DTC appears, check starter circuit first.
STEP
ACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Is there DTC P1500 (Engine starter signal circuit)?Go to DTC P1500
Diag. Flow Table.Go to Step 3.
3Check CKP Sensor for Resistance.
1) Disconnect CKP sensor connector with ignition
switch OFF.
2) Then check for proper connection to CKP sensor
at “W” and “B” wire terminals.
3) If OK, measure sensor resistance between
terminals. See Fig. 1.
CKP sensor resistance: 360 – 460 Ω at 20C,
68F
4) Measure resistance between each terminal and
ground.
Insulation resistance: 1 MΩ or more.
Were measured resistance valves in step 3) and 4)
as specified?Go to Step 4.Replace CKP sensor.
4Check visually CKP sensor and pulley for the
following. See Fig. 2.

Damage

No foreign material attached.

Correct installation.
Are they in good condition?“W” or “B” wire open or
shorted to ground, or
poor connection at
C01-23 or C01-24.
If wire and connection
are OK, intermittent
trouble or faulty ECM
(PCM).
Recheck for
intermittent referring
to “Intermittent and
Poor Connection” in
Section 0A.Clean, repair or
replace.
Fig. 1 for Step 3 Fig. 2 for Step 4

6-1-80 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
1. EGR valve coupler
INSPECTION
STEPACTIONYESNO
1Was ENGINE DIAG. FLOW TABLE performed?Go to Step 2.Go to ENGINE
DIAG. FLOW
TABLE.
2Do you have SUZUKI scan tool?Go to Step 3.Go to Step 5.
3EGR Valve Operation Check
1) With ignition switch OFF, install SUZUKI scan tool.
2) Check EGR system referring to section 6E2.
Is it in good condition?Go to Step 4.Go to Step 5.
4MAP Sensor Check
1) Check MAP sensor for performance referring to “MAP
Sensor Check” in DTC P0105 Diag. Flow Table.
Is check result satisfactory?Intermittent trouble
or faulty ECM
(PCM) Check for in-
termittent referring
to “Intermittent and
Poor Connection” in
section 0A.Repair or replace.
5EGR Valve Power Supply Circuit Check
1) With ignition switch OFF, disconnect EGR valve
coupler.
2) With ignition switch ON, check voltage between C13-2
and ground, C13-5 and ground. See Fig. 1.
Is each voltage 10 – 14 V?Go to Step 6.“R/B” wire.
6EGR Valve Stepping Motor Coil Circuit Check
1) With ignition switch OFF, connect EGR valve coupler
and disconnect ECM (PCM) couplers.
2) Check resistance between C02-6 and C02-2, C02-8,
C02-9, C02-17.
Is each resistance 20 – 24 Ω at 20C, 68F?Go to Step 7.Faulty “R/Y”,
“R/Bl”, “R”, “R/W”
wire or EGR valve.
7MAP Sensor Check
1) Check MAP sensor for performance referring to
“MAP Sensor Check” in DTC P0105 Diag. Flow Table.
Is check result satisfactory?EGR passage
clogged or EGR
valve malfunction.
If all above are OK,
intermittent trouble
or faulty ECM.
Check for intermit-
tent referring to
“Intermittent and
Poor Connection” in
section 0A.Repair or replace.
Fig. 1 for step 5

Radiator cooling fan relay
To
ECM
Main
relay
Relay
box
“RDTR”
(Radiator fan)Radiator cooling
Fan motor
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-85
DTC P0480 RADIATOR COOLING FAN CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low voltage at terminal C02-18 when engine coolant
temp. is 92C, 197F below.
2 driving cycle detection logic, continuous monitoring.
“B/W” or “P/G” circuit open or short

Radiator cooling fan relay malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Warm up engine until radiator cooling fan starts to operate.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.