Piston rings SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

1. No.1 cylinder
2. No.2 cylinder
3. No.3 cylinder
123
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-3
GENERAL INFORMATION
STATEMENT ON CLEANLINESS AND CARE
An automobile engine is a combination of many machined, honed,
polished and lapped surfaces with tolerances that are measured in
the thousands of an millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are serviced, care and
cleanliness are important.
Throughout this section, it should be understood that proper clean-
ing and protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard shop practice
even if not specifically stated.

A liberal coating of engine oil should be applied to friction areas
during assembly to protect and lubricate the surfaces on initial op-
eration.

Whenever valve train components, pistons, piston rings, con-
necting rods, rod bearings, and crankshaft journal bearings are
removed for service, they should be retained in order.
At the time of installation, they should be installed in the same
locations and with the same mating surfaces as when removed.

Battery cables should be disconnected before any major work is
performed on the engine.
Failure to disconnect cables may result in damage to wire har-
ness or other electrical parts.

Throughout this manual, the four cylinders of the engine are iden-
tified by numbers; No.1 (1), No.2 (2) and No.3 (3) counted from
crankshaft pulley side to flywheel side.
GENERAL INFORMATION ON ENGINE SERVICE
THE FOLLOWING INFORMATION ON ENGINE SERVICE
SHOULD BE NOTED CAREFULLY, AS IT IS IMPORTANT IN PRE-
VENTING DAMAGE, AND IN CONTRIBUTING TO RELIABLE EN-
GINE PERFORMANCE.

When raising or supporting engine for any reason, do not use a
jack under oil pan. Due to small clearance between oil pan and
oil pump strainer, jacking against oil pan may cause it to be bent
against strainer resulting in damaged oil pick-up unit.

It should be kept in mind, while working on engine, that 12-volt
electrical system is capable of violent and damaging short cir-
cuits.
When performing any work where electrical terminals can be
grounded, ground cable of the battery should be disconnected at
battery.

Any time the air cleaner, throttle body or intake manifold is re-
moved, the intake opening should be covered. This will protect
against accidental entrance of foreign material which could follow
intake passage into cylinder and cause extensive damage when
engine is started.

6-22 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
ENGINE DIAGNOSIS TABLE
Perform troubleshooting referring to following table when ECM (PCM) has detected no DTC and no abnormality
has been found in visual inspection and engine basic inspection previously.
Condition
Possible CauseReferring Item
Hard Starting
(Engine cranks OK)Ignition system out of order

Faulty spark plug

Leaky high-tension cord

Loose connection or disconnection of high-
tension cords or lead wires

Faulty ignition coil
Fuel system out of order

Dirty or clogged fuel hose or pipe

Malfunctioning fuel pump

Air inhaling from intake manifold gasket or
throttle body gasket

Fuel injector resistor malfunction
Engine and emission control system out of
order

Faulty idle control system

Faulty ECT sensor or MAP sensor

Faulty ECM (PCM)
Low compression

Poor spark plug tightening or faulty gasket

Compression leak from valve seat

Sticky valve stem

Weak or damaged valve springs

Compression leak at cylinder head gasket

Sticking or damaged piston ring

Worn piston, ring or cylinder
Others

Malfunctioning PCV valve
Spark plugs in Section 6F
High-tension cords in Section 6F
High-tension cords in Section 6F
Ignition coil in Section 6F
Diagnostic Flow Table B-3
Diagnostic Flow Table B-3
Fuel injector resistor in Section 6E1
Diagnostic Flow Table P0505
ECT sensor or MAP sensor in
Section 6E1
Compression check in Section
6A
Spark plugs in Section 6F
Valves inspection in Section 6A
Valves inspection in Section 6A
Valve springs inspection in
Section 6A
Cylinder head inspection in
Section 6A
Cylinders, pistons and piston rings
inspection in Section 6A
Cylinders, pistons and piston rings
inspection in Section 6A
PCV system in Section 6E1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-23
ConditionPossible CauseReferring Item
Low oil pressure
Improper oil viscosity

Malfunctioning oil pressure switch

Clogged oil strainer

Functional deterioration of oil pump

Worn oil pump relief valve

Excessive clearance in various sliding partsEngine oil and oil filter change in
Section 0B
Oil pressure switch inspection in
Section 8
Oil pan and oil pump strainer
cleaning in Section 6A
Oil pump in Section 6A
Oil pump in Section 6A
Engine noise
Note: Before
checking mechanical
noise, make sure
that:

Specified spark
plug in used.

Specified fuel is
used.Valve noise

Improper valve lash

Worn valve stem and guide

Weak or broken valve spring

Warped or bent valve
Piston, ring and cylinder noise

Worn piston, ring and cylinder bore
Connecting rod noise

Worn rod bearing

Worn crank pin

Loose connecting rod nuts

Low oil pressure
Crankshaft noise

Low oil pressure

Worn bearing

Worn crankshaft journal

Loose bearing cap bolts

Excessive crankshaft thrust play
Valve lash in Section 6A
Valves inspection in Section 6A
Valve springs inspection in
Section 6A
Valves inspection in Section 6A
Pistons and cylinders inspection
in Section 6A
Crank pin and connecting rod
bearing inspection in Section 6A
Crank pin and connecting rod
bearing inspection in Section 6A
Connecting rod installation in
Section 6A
Previously outlined
Previously outlined
Crankshaft and bearing
inspection in Section 6A
Crankshaft and bearing
inspection in Section 6A
Crankshaft inspection in
Section 6A
Crankshaft thrust play inspection
in Section 6A

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-3
GENERAL INFORMATION
STATEMENT ON CLEANLINESS AND CARE
An automobile engine is a combination of many machined, honed,
polished and lapped surfaces with tolerances that are measured in
the thousands of an millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are serviced, care and
cleanliness are important.
Throughout this section, it should be understood that proper clean-
ing and protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard shop practice
even if not specifically stated.

A liberal coating of engine oil should be applied to friction areas
during assembly to protect and lubricate the surfaces on initial op-
eration.

Whenever valve train components, pistons, piston rings, con-
necting rods, rod bearings, and crankshaft journal bearings are
removed for service, they should be retained in order.
At the time of installation, they should be installed in the same
locations and with the same mating surfaces as when removed.

Battery cables should be disconnected before any major work is
performed on the engine.
Failure to disconnect cables may result in damage to wire har-
ness or other electrical parts.

Throughout this manual, the four cylinders of the engine are iden-
tified by numbers; No.1 (1), No.2 (2), No.3 (3) and No.4 (4)
counted from crankshaft pulley side to flywheel side.
GENERAL INFORMATION ON ENGINE SERVICE
THE FOLLOWING INFORMATION ON ENGINE SERVICE
SHOULD BE NOTED CAREFULLY, AS IT IS IMPORTANT IN PRE-
VENTING DAMAGE, AND IN CONTRIBUTING TO RELIABLE EN-
GINE PERFORMANCE.

When raising or supporting engine for any reason, do not use a
jack under oil pan. Due to small clearance between oil pan and
oil pump strainer, jacking against oil pan may cause it to be bent
against strainer resulting in damaged oil pick-up unit.

It should be kept in mind, while working on engine, that 12-volt
electrical system is capable of violent and damaging short cir-
cuits.
When performing any work where electrical terminals can be
grounded, ground cable of the battery should be disconnected at
battery.

Any time the air cleaner, throttle body or intake manifold is re-
moved, the intake opening should be covered. This will protect
against accidental entrance of foreign material which could follow
intake passage into cylinder and cause extensive damage when
engine is started.

6-1-22 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ENGINE DIAGNOSIS TABLE
Perform troubleshooting referring to following table when ECM (PCM) has detected no DTC and no abnormality
has been found in visual inspection and engine basic inspection previously.
Condition
Possible CauseReferring Item
Hard Starting
(Engine cranks OK)Ignition system out of order

Faulty spark plug

Leaky high-tension cord

Loose connection or disconnection of high-
tension cords or lead wires

Faulty ignition coil
Fuel system out of order

Dirty or clogged fuel hose or pipe

Malfunctioning fuel pump

Air inhaling from intake manifold gasket or
throttle body gasket
Engine and emission control system out of
order

Faulty idle air control system

Faulty ECT sensor or MAP sensor

Faulty ECM (PCM)
Low compression

Poor spark plug tightening or faulty gasket

Compression leak from valve seat

Sticky valve stem

Weak or damaged valve springs

Compression leak at cylinder head gasket

Sticking or damaged piston ring

Worn piston, ring or cylinder
Others

Malfunctioning PCV valve
Spark plugs in Section 6F1
High-tension cords in Section 6F1
High-tension cords in Section 6F1
Ignition coil in Section 6F1
Diagnostic Flow Table B-3
Diagnostic Flow Table B-3
Diagnostic Flow Table B-4
ECT sensor or MAP sensor in
Section 6E2
Compression check in Section
6A1
Spark plugs in Section 6F1
Valves inspection in Section 6A1
Valves inspection in Section 6A1
Valve springs inspection in
Section 6A1
Cylinder head inspection in
Section 6A1
Cylinders, pistons and piston rings
inspection in Section 6A1
Cylinders, pistons and piston rings
inspection in Section 6A1
PCV system in Section 6E2

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-23
ConditionPossible Cause]Referring Item
Low oil pressure
Improper oil viscosity

Malfunctioning oil pressure switch

Clogged oil strainer

Functional deterioration of oil pump

Worn oil pump relief valve

Excessive clearance in various sliding partsEngine oil and oil filter change in
Section 0B
Oil pressure switch inspection in
Section 8
Oil pan and oil pump strainer
cleaning in Section 6A1
Oil pump in Section 6A1
Oil pump in Section 6A1
Engine noise
Note: Before
checking mechanical
noise, make sure
that:

Specified spark
plug in used.

Specified fuel is
used.Valve noise

Improper valve lash

Worn valve stem and guide

Weak or broken valve spring

Warped or bent valve
Piston, ring and cylinder noise

Worn piston, ring and cylinder bore
Connecting rod noise

Worn rod bearing

Worn crank pin

Loose connecting rod nuts

Low oil pressure
Crankshaft noise

Low oil pressure

Worn bearing

Worn crankshaft journal

Loose bearing cap bolts

Excessive crankshaft thrust play
Valve lash in Section 6A1
Valves inspection in Section 6A1
Valve springs inspection in
Section 6A1
Valves inspection in Section 6A1
Pistons and cylinders inspection
in Section 6A1
Crank pin and connecting rod
bearing inspection in Section 6A1
Crank pin and connecting rod
bearing inspection in Section 6A1
Connecting rod installation in
Section 6A1
Previously outlined
Previously outlined
Crankshaft and bearing
inspection in Section 6A1
Crankshaft and bearing
inspection in Section 6A1
Crankshaft inspection in
Section 6A1
Crankshaft thrust play inspection
in Section 6A1

6A
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1
SECTION 6A
ENGINE MECHANICAL
(G10, 1-CAM 6-VALVES ENGINE)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
For the descriptions (items) not found in this section, refer to the same section of Service Manual men-
tioned in FOREWORD of this manual.
CONTENTS
ON-VEHICLE SERVICE6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Vacuum Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Check6A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head Cover6A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body and Intake Manifold 6A- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold6A- 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Belt and Belt Tensioner 6A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camshaft and Hydraulic Valve Lash Adjuster 6A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Lash Adjuster Noise Diagnosis 6A-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves and Cylinder Head6A-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pistons, Piston Rings, Connecting Rods and Cylinders 6A-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR OVERHAUL6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Assembly6A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Bearings, Crankshaft and Cylinder Block 6A-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS6A-31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. Cylinder block
2. Feeler gauge
3. Piston ring
4. 120 mm (4.72 in.)1. Top ring
2. 2nd ring
3. Oil ring
4. Piston
5. Connecting rod
6. Connecting rod bearing cap
7. Connecting rod bearing
8. Piston pin
9. Connecting rod nut : Tightening Torque
: Apply engine oil to sliding
: surfaces of each part.
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-23
PISTONS, PISTON RINGS, CONNECTING RODS AND CYLINDERS
INSPECTION
Piston Rings
To measure end gap, insert piston ring into cylinder bore as shown
in figure and then measure gap by using thickness gauge.
If measured gap is out of specification, replace ring.
NOTE:
Decarbon and clean the top of cylinder bore before inserting
piston ring.
Item
StandardLimit
Piston
Top ring0.15 – 0.30 mm
(0.0059 – 0.0118 in.)0.7 mm
(0.0275 in.)
Piston
ring end
gap
2nd ring0.20 – 0.35 mm
(0.0079 – 0.0138 in.)0.7 mm
(0.0275 in.)
ga
Oil ring0.20 – 0.60 mm
(0.0079 – 0.0236 in.)1.8 mm
(0.0708 in.)

1. Cylinder block
2. Front oil seal
3. Main bearing
4. Bearing cap
5. Cap washer
6. Cap bolt
7. Timing pulley key
8. Crankshaft
9. Thrust bearing:
Set oil grooves of bearing to weds.
10. Rear oil seal
11. Pin
12. Oil seal housing gasket
13. Oil seal housing
14. Housing bolt
15. Input shaft bearing
16. Flywheel
17. Flywheel bolt
: Tightening Torque
: Do not reuse
: Apply engine oil to sliding
: surfaces of each part.
78 N.m (7.8 kg-m)
12 N
.m (1.2 kg-m)
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-27
MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK
REMOVAL
1) Remove engine with transmission from body as previously out-
lined.
2) Remove transmission from engine, and then remove clutch and
flywheel (drive plate for A / T).
3) Remove water pump belt, generator bracket, crankshaft pulley,
timing belt, and crankshaft timing belt pulley etc.
4) Remove cylinder head assembly.
5) Remove oil pan and oil pump strainer.
6) Remove pistons and connecting rods.
7) Remove oil pump and oil seal housing.
8) Remove main bearing caps and crankshaft.

2. Upper half of bearing
(a)
6A-28 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
INSTALLATION
NOTE:

All parts to be installed must be perfectly clean.

Be sure to oil crankshaft journals, journal bearings, thrust
bearings, crankpins, connecting rod bearings, pistons, pis-
ton rings and cylinder bores.

Journal bearings, bearing caps, connecting rods, rod bear-
ings, rod bearing caps, pistons and piston rings are in com-
bination sets. Do not disturb combination and try to see that
each part goes back to where it came from, when installing.
1) Fit main bearings to cylinder block (1).
Among two halves of main bearing, one halt has oil groove (3).
Install this half with oil groove to cylinder block, and another half
without oil groove to bearing cap.
Make sure that two halves are painted in the same color.
2) Fit thrust bearings (1) to cylinder block between No.2 and No.3
cylinders. Face oil groove (2) sides to crank webs.
3) Put crankshaft on cylinder block.
4) Fit bearing caps sequentially in ascending order, 1, 2, 3 and 4,
starting from pulley side. Be sure to point arrow mark (2) (on
each cap) to crankshaft pulley side (1).
Gradual and uniform tightening is important for bearing cap
bolts. Make sure that four caps become tight equally and pro-
gressively till specified torque is attained.
Tightening Torque
(a): 53 N
.m (5.3 kg-m, 38.5 lb-ft)
NOTE:
After tightening cap bolts, check to be sure that crankshaft
rotates smoothly when turned by hand.