door lock SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

“A”: Oil point
1. Upper hinge
2. Lower hinge
3. Door
4. Body
MAINTENANCE AND LUBRICATION 0B-19
ITEM 6-10
All Latches, Hinges and Locks Inspection
Doors
Check that each door of front, rear and back doors opens and
closes smoothly and locks securely when closed.
If any malfunction is found, lubricate hinge and latch or repair door
lock system.
Engine hood
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.). Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

MAINTENANCE AND LUBRICATION 0B-21
[Parking brake]
Check that lever has proper travel.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to “HI” position and mode lever to
defroster position for this check. WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSE, SF, SG, SH or SJ (Refer to engine oil viscosity chart in item 1-4.)
Engine coolantEthylene-glycol base coolant (“Antifreeze / Anticorrosion coolant”)
Brake fluidDOT3
Manual transmission oilSee SECTION 7A
Rear differential oilSee SECTION 7E
Automatic transmission fluidAn equivalent of DEXRON-IIE or DEXRON-III
Power steering fluidSee material table on SECTION 3B1
Door hingesEngine oil
Engine hood latchEngine oil
Key lock cylinderSpray lubricant

TYPE 1 TYPE 2
BODY ELECTRICAL SYSTEM 8-3
KEYLESS ENTRY SYSTEM (IF EQUIPPED)
The keyless entry system uses radio wave. When the button on the transmitter is pressed, a signal is transmitted
in the form of radio wave to the receiver. Then the signal causes the door lock controller to lock and unlock the door.
The door locks can not operated with the transmitter when either of the following conditions applies.

For 2 seconds after the ignition switch is turned from ON to OFF position.

The ignition switch is at ON or START position.

Any door is open.
DIAGNOSIS
KEYLESS ENTRY SYSTEM (IF EQUIPPED)
ConditionPossible CauseCorrection
The power door lock function
is available but the keyless
entry function is not.
Fuse blown

Code registration error

Transmitter battery dead

Wiring or grounding faulty

Receiver faulty

Transmitter faultyReplace fuse to check for short.
Register code.
Replace battery.
Repair as necessary.
Replace.
Replace.
Only one power door lock
does not operate.
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair as necessary
Replace.
Operation distance unstable.
Transmitter battery dead

Transmitter faultyReplace battery.
Replace.
NOTE:

The operation distance of this system varies depending on the position where the transmitter is oper-
ated, at the front side, the rear side or the lateral side. The distance can be affected by radio noises from
a TV station, a power plant, a broadcasting station and so forth.
ON-VEHICLE SERVICE
ENGINE COOLANT TEMP. (ECT) METER AND
SENSOR
ECT SENSOR
INSPECTION
1) Warm up ECT sensor (1) observing resistance between sensor
terminal (2) and sensor unit (1). Resistance should be de-
creased with increase of its temperature.
2) Check resistance between sensor terminal (2) and sensor unit
(1). If check result is not as specified below, replace sensor.
Temperature
Resistance
50C (122F)136 – 216 Ω

1. Slot
1. To power door lock controller (Unlock)
2. To power door lock controller (Lock)
3. To IG switch
5. To door switch
6. To GND
8. To battery
8-4 BODY ELECTRICAL SYSTEM
KEYLESS ENTRY SYSTEM (IF EQUIPPED)
TRANSMITTER
REPLACEMENT OF THE BATTERY
If the transmitter becomes unreliable, replace the battery.
As the battery power is consumed, the operation distance will be
shorter.
1) Put the edge of a coin or a flat blade screw driver in the slot of
the transmitter and pry it open.
2) Replace the battery (lithium disc-type CR2025 or equivalent) so
its (+) terminal faces the “+” mark of the transmitter.
CAUTION:
Use care not to allow grease or dirt to be attached on the
printed circuit board and the battery.
3) Close the transmitter firmly.
4) Make sure the door locks can be operated with the transmitter.
NOTE:

To prevent theft, be sure to break the transmitter before
discarding it.

Dispose of the used battery properly according to appli-
cable rules or regulations. Do not dispose of lithium bat-
teries with ordinary household trash.
RECEIVER
INSPECTION
Using a tester, check for continuity and voltage between each termi-
nal of the connector connected to the receiver and the body ground
at the following condition.
TerminalCheck forConditionStandard
value
1Continuity
Unlock the driver’s seat
side door by using the
key.No continuity

Continuity
2ContinuityLock the driver’s seat side
door by using the key.No continuity

Continuity
3Voltage
Insert the ignition key and
turn ON the ignition
switch.
0 V
10 – 14 V
5VoltageOpen any one of all
closed doors.10 – 14 V
0 V
6ContinuityAnytimeContinuity
8VoltageAnytime10 – 14 V

BODY ELECTRICAL SYSTEM 8-5
CODE REGISTRATION PROCEDURE
1) Start of code registration
(Initial conditions: IG switch OFF, all doors closed)
2) Open the door and then turn ON the IG switch within 10 seconds.
3) Turn OFF the IG switch within 10 seconds after it is turned ON.
4) Turn the door switch ON and OFF 3 times within 20 seconds af-
ter the IG switch is turned OFF.
5) Within 10 seconds after the door switch is turned ON, turn ON
the IG switch and then OFF within next 10 seconds.
6) After LOCK and UNLOCK operation once, the registration mode
is set.
7) Press the UNLOCK button of the transmitter once within 60 se-
conds after the registration mode is set.
8) LOCK and UNLOCK operation once again completes the regis-
tration procedure.
NOTE:

Perform the above procedure to register a code.

Two codes can be registered.

When a new code is registered, the oldest one will be
cleared.