ignition SUZUKI SWIFT 2000 1.G Transmission Service Workshop Manual

AIR BAG SYSTEM 10B-61
DEPLOYMENT/ACTIVATION OUTSIDE VEHI-
CLE
Use this procedure when the vehicle itself is used again (only the
air bag (inflator) module(s) and seat belt pretensioner(s) are dis-
posed).
1) Turn ignition switch to “LOCK”, position remove key and put
on safety glasses.
2) Check that there is no open, short or damage in special tool
(deployment harness). If any faulty is found, do not use it
and be sure to use new deployment harness.
Special tool
(A) : 09932-75030
3) Short (1) the two deployment harness leads together by fully
seating one banana plug into the other.
4) Remove air bag (inflator) module(s) and seat belt preten-
sioner(s) from vehicle, referring to SECTION 3C, 10B and
10. WARNING:
Deployment harness shall remain shorted and not be
connected to a power source until the air bag is to be
deployed and seat belt pretensioner is to be activated.
WARNING:
Always carry live air bag (inflator) module with trim
cover away from you.
When storing a live air bag (inflator) module or when
leaving a live air bag (inflator) module unattended on a
bench or other surface, always face the bag and trim
cover up and away from the surface. As the live pas-
senger air bag (inflator) module must be placed with its
bag (trim cover) facing up, place it on the workbench
with a slit (1) or use the workbench vise (2) to hold it
securely at its lower mounting bracket (3).
This is necessary so that a free space is provided to
allow the air bag to expand in the unlikely event of
accidental deployment.
Failure to follow procedures may result in personal
injury.
1
3
32

AIR BAG SYSTEM 10B-67
DEPLOYMENT/ACTIVATION INSIDE VEHICLE
Use this procedure when scrapping the entire vehicle including
the air bag (inflator) modules and seat belt pretensioners.
1) Turn ignition switch to “LOCK” position, remove key and put
on safety glasses.
2) Remove all loose objects from front seats and instrument
panel.
3) [For driver air bag (inflator) module]
Disconnect contact coil connector (1) located near the base
of the steering column.
[For passenger air bag (inflator) module]
Remove glove box from instrument panel and disconnect
passenger air bag (inflator) module connector (2).
[For seat belt pretensioner]
Remove both side (driver and passenger side) center pillar
lower trim and disconnect seat belt pretensioner connectors
(3).
4) Confirm that each air bag (inflator) module is securely
mounted.
5) Check that there is no open, short or damage in special tool
(deployment harness). If any faulty condition is found, do not
use it and be sure to use new deployment harness.
Special tool
(A) : 09932-75030
6) Short (1) the two deployment harness leads together by fully
seating one banana plug into the other.
7) Connect deployment harness connector to air bag (inflator)
module (driver or passenger) or seat belt pretensioner
(driver or passenger) and lock connector with lock lever.
a) Connect connector.
b) Lock connector with lock lever.CAUTION:
When vehicle itself will be used again, deploy/activate
the air bag and pretensioner outside vehicle according to
“DEPLOYMENT/ACTIVATION OUTSIDE VEHICLE”, for
deploying/activating it inside will cause the instrument
panel, glove box and their vicinity to be deformed.
Failure to observe this CAUTION may require unneeded
vehicle inspection and repair.
1
2
For Driver Air Bag (Inflator) Module
For Passenger Air Bag (Inflator) Module
For Seat Belt Pretensioner
WARNING:
Deployment harness shall remain shorted and not be
connected to a power source until the air bag is to be
deployed and seat belt pretensioner is to be activated.
(A)
1
For Driver Air Bag (inflator) Module