Differential SUZUKI SX4 2006 1.G Service Owners Manual

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-137
2) As shown in figure, facing groove (2) side upward,
install final driven gear (1) to differential case.
3) Tighten final gear bolts (1) to specified torque.
NOTE
To avoid rust, apply A/T fluid to final driven
gear after installation.

Tightening torque
Final gear bolt (a): 78 N·m (7.8 kgf-m, 56.5 lb-ft)
4) After applying A/T fluid to output shaft speed sensor
(VSS) drive gear (1), install output shaft speed
sensor drive gear.
5) Install new differential side RH bearing (1) by using
special tool and hydraulic press.
NOTE
Replace differential side RH bearing together
with bearing cup as a set.

Special tool
(A): 09913–701236) Install new differential side LH bearing (1) by using
special tool and hydraulic press.
NOTE
Replace differential side LH bearing together
with bearing cup as a set.

Special tool
(A): 09913–70123
Differential Assembly InspectionS6RW0D5106054
1) Hold differential case subassembly with soft jawed
vice and set special tools as shown.
Special tool
(A): 09900–20607
(B): 09900–20701
2) Measure differential gear thrust play.
Differential gear thrust play
Standard: 0.06 – 0.22 mm (0.002 – 0.009 in.)
3) If thrust play is out of specification, replace
differential case subassembly.
2. Final driven gear
I2RH0B510230-01
I2RH0B510231-01
I2RH0B510232-01
I2RH0B510233-01
I2RH0B510234-01
I2RH0B510235-01

Downloaded from www.Manualslib.com manuals search engine 5A-138 Automatic Transmission/Transaxle:
Torque Converter Housing Disassembly and
Reassembly
S6RW0D5106055
Disassembly
1) Remove fluid reservoir RH plate (1) and lubrication
tube clamp (2).
2) Remove lubrication LH tube (1) and RH tube (2).
NOTE
Do not bend lubrication tube with excessive
force.

3) Remove differential side oil seal (1).4) Remove countershaft RH bearing cup by using
special tools.
Special tool
(A): 09944–96011
(B): 09942–15511
5) Remove differential side RH bearing cup by using
special tools.
Special tool
(A): 09944–96011
(B): 09942–15511
6) Remove torque converter case plugs (1).
I2RH0B510236-01
I2RH0B510237-01
I2RH0B510238-01
I2RH0B510239-01
I2RH0B510240-01
I2RH0B510241-01

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-139
Reassembly
1) After applying A/T fluid to new O-rings, fit them to
housing plugs. Finally install plugs to torque
converter housing.
Tightening torque
Torque converter housing plug (a): 7.5 N·m (0.75
kgf-m, 5.5 lb-ft)
2) Using special tools, assemble differential side RH
bearing cup.
Special tool
(A): 09924–74510
(B): 09944–88220
3) Using special tool, install countershaft RH bearing
cup.
Special tool
(A): 09924–74510
(B): 09944–882204) Using special tools, install new differential side oil
seal to torque converter housing.
Special tool
(A): 09913–75510
Differential side oil seal installing depth
“a”: 13.2 – 14.2 mm (0.52 – 0.56 in.)
5) Apply grease to oil seal lip.
“A”: Grease 99000–25030 (SUZUKI Super
Grease C)
6) Install lubrication LH tube (1) and RH tube (2).
7) Install fluid reservoir RH plate (1) and lubrication
tube clamp (2).
Tightening torque
Lubrication tube clamp bolt (a): 5.5 N·m (0.55
kgf-m, 4.0 lb-ft)
Fluid reservoir RH plate bolt (b): 5.5 N·m (0.55
kgf-m, 4.0 lb-ft)
I2RH0B510242-01
(A)
(B)
I3RM0B510063-01
(B)(A)
I3RM0B510064-01
(A) “a”
“A”
I5RW0C510065-02
I2RH0B510237-01
I2RH0B510246-01

Downloaded from www.Manualslib.com manuals search engine 5A-140 Automatic Transmission/Transaxle:
Transaxle Case Disassembly and ReassemblyS6RW0D5106056
Disassembly
1) Remove differential side oil seal (1).
2) Remove countershaft LH bearing cup and shim with
special tools.
Special tool
(A): 09944–96011
(B): 09942–15511
3) Remove differential side LH bearing cup and shim
with special tools.
Special tool
(A): 09944–96011
(B): 09942–15511Reassembly
1) Using special tools, assemble shim and differential
side LH bearing cup.
NOTE
Use shim with same thickness as the
removed one.

Special tool
(A): 09924–74510
(B): 09944–88220
2) Using special tools, assemble shim and countershaft
LH bearing cup.
NOTE
Use shim with same thickness as the
removed one.

Special tool
(A): 09924–74510
(B): 09944–88220
I2RH0B510247-01
I2RH0B510248-01
I2RH0B510249-01
(B) (A)
I3RM0B510065-01
(B)(A)
I3RM0B510066-01

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-141
3) Install new differential side oil seal to transaxle case
by using special tools.
Special tool
(A): 09913–75810
Differential side oil seal installing depth
“a”: 3.8 – 4.8 mm (0.15 – 0.19 in.)
4) Apply grease to oil seal lip.
“A”: Grease 99000–25030 (SUZUKI Super
Grease C)
Automatic Transaxle Unit Inspection and
Adjustment
S6RW0D5106057
Inspection
Brake discs
Dry and inspect them for pitting, burn flaking, significant
wear, glazing, cracking, charring and chips or metal
particles imbedded in lining.
If discs show any of the above conditions, replacement
is required.
NOTE
• If disc lining is exfoliated or discolored,
replace all discs.
• Before assembling new discs, soak them
in A/T fluid for at least two hours.

Brake separator plates and retaining plates
Dry plates and check for discoloration. If plate surface is
smooth and even color smear is indicated, plate should
be reused. If severe heat spot discoloration or surface
scuffing is indicated, plate must be replaced.
Brake return spring subassembly
Measure free length of each brake return springs.
Evidence of extreme heat or burning in the area of clutch
may have caused springs to take heat set and would
require their replacement.
Free length of 1st & reverse brake return spring
subassembly
“a”: 21.71 mm (0.855 in.)
Free length of 2nd brake return spring subassembly
“a”: 15.85 mm (0.624 in.)
NOTE
• Do not apply excessive force when
measuring spring free length.
• Perform measurement at several points.

(A)“a”
“A”
I5RW0C510066-02
I2RH01510147-01
I2RH0B510253-01
I2RH0B510173-01

Downloaded from www.Manualslib.com manuals search engine 5A-142 Automatic Transmission/Transaxle:
One-way clutch No.1 assembly
1) Install one-way clutch No.1 assembly (2) to rear
planetary sun gear subassembly (1).
2) Securing rear planetary sun gear subassembly,
ensure that one-way clutch No.1 assembly rotates
only in one direction.
If the one-way clutch rotates in both directions or it
does not rotate in either direction, replace it with new
one.
Adjustment
Differential side bearing preload
1) After applying A/T fluid to differential assembly, fit it
to transaxle case.
2) Install torque converter housing to transaxle case,
then tighten bolts (1) to specified torque.
Tightening torque
Torque converter housing bolt (a): 33 N·m (3.3
kgf-m, 24.0 lb-ft)3) Measure bearing preload (a) by using a special tool.
Special tool
(A): 09928–06050
Differential side bearing preload (a) measured as
starting torque
In the case of new bearing: 0.78 – 1.37 N⋅m (7.9 –
13.9 kg-cm, 0.58 – 1.01 lb-ft)
In the case of reused bearing: 0.39 – 0.69 N⋅m
(3.9 – 6.9 kg-cm, 0.29 – 0.51 lb-ft)
4) If bearing preload is out of specification, select shim
with suitable thickness from among the list below
and replace it. Then adjust differential side bearing
preload within specification.
Available shim thickness
NOTE
Record measured differential side bearing,
because it is necessary to adjust
countershaft bearing preload.

5) Remove differential assembly.
I2RH0B510254-01
I2RH0B510255-01
Thickness Identification mark
1.80 mm (0.070 in.) A
1.85 mm (0.072 in.) B
1.90 mm (0.074 in.) C
1.95 mm (0.076 in.) D
2.00 mm (0.078 in.) E
2.05 mm (0.080 in.) F
2.08 mm (0.081 in.) G
2.11 mm (0.083 in.) H
2.14 mm (0.084 in.) J
2.17 mm (0.085 in.) K
2.20 mm (0.087 in.) L
2.23 mm (0.088 in.) M
2.26 mm (0.089 in.) N
2.29 mm (0.090 in.) P
2.32 mm (0.091 in.) Q
2.35 mm (0.092 in.) R
2.40 mm (0.094 in.) S
2.45 mm (0.096 in.) T
2.50 mm (0.098 in.) U
2.55 mm (0.100 in.) V
2.60 mm (0.102 in.) W
2.65 mm (0.104 in.) X
2.70 mm (0.106 in.) Y
I2RH0B510256-01

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-143
Countershaft bearing preload
1) After applying A/T fluid to countershaft assembly (1)
and differential assembly (2), fit them.
2) Install torque converter housing to transaxle case,
then tighten bolts to specified torque.
Tightening torque
Torque converter housing bolt: 33 N·m (3.3 kgf-
m, 24.0 lb-ft)
3) Measure bearing preload (b) by using special tool.
Special tool
(A): 09928–06050
Countershaft bearing preload (b) measured as
starting torque
In the case of new bearing: 0.33 – 0.76 N⋅m (3.3 –
7.6 kg-cm, 0.24 – 0.55 lb-ft)
In the case of reused bearing: 0.17 – 0.38 N⋅m
(1.7 – 3.8 kg-cm, 0.12 – 0.28 lb-ft)4) If bearing preload is out of specification, select shim
with suitable thickness from among the list below
and replace it. Then adjust countershaft bearing
preload within specification.
Available shim thickness
5) Remove differential assembly and countershaft
assembly. Countershaft bearing
preload=(b) – Differential side bearing
preload (a)
I2RH0B510257-01
I3RM0B510067-01
Thickness Identification mark
1.70 (0.066 in.) 1
1.75 (0.068 in.) 2
1.80 (0.070 in.) 3
1.85 (0.072 in.) 4
1.90 (0.074 in.) 5
1.93 (0.075 in.) 6
1.96 (0.077 in.) 7
1.99 (0.078 in.) A
2.02 (0.079 in.) B
2.05 (0.080 in.) C
2.08 (0.081 in.) D
2.11 (0.083 in.) E
2.14 (0.084 in.) F
2.17 (0.085 in.) G
2.20 (0.086 in.) H
2.25 (0.088 in.) K
2.30 (0.090 in.) L
2.35 (0.092 in.) M
2.40 (0.094 in.) N
2.45 (0.096 in.) P
2.50 (0.098 in.) Q
2.55 (0.100 in.) R
2.60 (0.102 in.) S
2.65 (0.104 in.) U
2.70 (0.106 in.) W

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-153
48) Install transaxle rear cover assembly on transaxle
case.
49) Install hook (2) to location shown in figure.
50) Tighten rear cover bolts (1).
Tightening torque
Rear cover bolt (a): 25 N·m (2.5 kgf-m, 18.0 lb-ft)
51) Install fluid reservoir LH plate (1).
Tightening torque
Fluid reservoir LH plate bolt (a): 10 N·m (1.0 kgf-
m, 7.5 lb-ft)
52) After applying A/T fluid to new governor apply No.2
gasket (1), install it to transaxle case.53) After applying A/T fluid to differential assembly (1)
and countershaft assembly (2), install them to
transaxle case.
54) After applying A/T fluid to direct clutch hub (1), install
it to planetary gear assembly.
55) After applying A/T fluid to input shaft rear thrust
bearing (1) and thrust bearing race (2), install them
into direct clutch hub (3).
56) After applying A/T fluid to input shaft front thrust
bearing (1), install it to direct clutch assembly (2).
I3RM0B510068-01
I2RH0B510303-01
I2RH0B510304-01
1
2
I4RS0A510036-01
I2RH0B510306-01
I2RH0B510307-01
I2RH0B510308-01

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-161
Specifications
Tightening Torque SpecificationsS6RW0D5107001
NOTE
The specified tightening torque is also described in the following.
“Select Cable Components”
“Automatic Transaxle Unit Components”
“Automatic Transaxle Assembly Components”
“Oil Pump Assembly Components”
“Transaxle Rear Cover (O/D and 2nd Coast Brake Piston) Assembly Components”
“Valve Body Assembly Components”
“Differential Assembly Components”

Reference:
For the tightening torque of fastener not specified in this section, refer to “Fasteners Information in Section 0A”. Fastening partTightening torque
Note
N⋅mkgf-mlb-ft
A/T fluid drain plug 17 1.7 12.5) / ) / )
Transmission range sensor bolt 5.5 0.55 4.0) / )
Output shaft speed sensor (VSS) bolt 13 1.3 9.5) / )
Input shaft speed sensor bolt 5.5 0.55 4.0) / )
Valve body harness connector bolt 5.5 0.55 4.0) / )
Shift solenoid bolt 11 1.1 8.0)
Oil strainer bolt 10 1.0 7.5) / )
Oil pan bolt 7.0 0.7 5.0) / )
Engine oil pan bolt 55 5.5 40.0)
Transaxle and engine fastening bolt 85 8.5 61.5)
Transaxle and engine fastening nut 85 8.5 61.5)
Drive plate to torque converter bolt 19 1.9 14.0)
Transaxle housing lower plate bolt 11 1.1 8.0)
Oil pump subassembly bolt 10 1.0 7.5)
Rear cover plug 7.5 0.75 5.5)
Solenoid valve bolt 11 1.1 8.0)
Final gear bolt 78 7.8 56.5)
Torque converter housing plug 7.5 0.75 5.5)
Lubrication tube clamp bolt 5.5 0.55 4.0)
Fluid reservoir RH plate bolt 5.5 0.55 4.0)
Torque converter housing bolt 33 3.3 24.0) / ) / )
Manual detent spring bolt 10 1.0 7.5)
Parking lock pawl bracket bolt 7.5 0.75 5.5)
Rear cover bolt 25 2.5 18.0)
Fluid reservoir LH plate bolt 10 1.0 7.5)
Oil pump assembly bolt 25 2.5 18.0)
Transaxle case plug 7.5 0.75 5.5)
Valve body bolt 11 1.1 8.0)
Fluid cooler pipe union 25 2.5 18.0)
Fluid cooler pipe union bolt 35 3.5 25.5)
Fluid cooler pipe bracket bolt 10 1.0 7.5)
Fluid filler tube bolt 10 1.0 7.5)
Select cable bracket bolt 23 2.3 17.0)
Select cable clamp bolt 13 1.3 9.5)
Transmission range sensor lock nut 7 0.7 5.0)
Manual select lever nut 13 1.3 9.5)

Downloaded from www.Manualslib.com manuals search engine 5A-162 Automatic Transmission/Transaxle:
Special Tools and Equipment
Recommended Service MaterialS6RW0D5108001
NOTE
Required service material is also described in the following.
“Select Cable Components”
“Automatic Transaxle Assembly Components”
“Oil Pump Assembly Components”
“Direct Clutch Assembly Components”
“Forward and Reverse Clutch Assembly Components”
“2nd Brake Piston Assembly Components”
“Transaxle Rear Cover (O/D and 2nd Coast Brake Piston) Assembly Components”
“Countershaft Assembly Components”
“Valve Body Assembly Components”
“Differential Assembly Components”

Special ToolS6RW0D5108002
Material SUZUKI recommended product or Specification Note
Grease SUZUKI Super Grease A P/No.: 99000–25011) / )
SUZUKI Super Grease C P/No.: 99000–25030) / ) / ) / ) / ) / )
Sealant SUZUKI Bond No.1216B P/No.: 99000–31230) / ) / )
09900–20605 09900–20607
Dial calipers (1/100 mm, 10-
34 mm)Dial gauge
) / ) / )) / ) / ) / ) / ) / ) / ) /
) / ) / ) / )
09900–20701 09913–50121
Magnetic stand Oil seal remover
) / ) / ) / ) / ) / ) / ) /
) / ) / ) / )) / )
09913–61510 09913–70123
Bearing puller Bearing installing tool
)) / )
09913–75510 09913–75810
Bearing installer Bearing installer
) / )) / )