run flat TESLA MODEL S 2022 Owner´s Manual

Key Fob
You can quickly familiarize yourself with the
key fob by thinking of it as a miniature version
of
Model S, with the Tesla badge representing
the front. The key has buttons that feel like
softer areas on the surface.
1.
Rear trunk - Double-click to open or close
the rear trunk. Hold down for one to two
seconds to open the charge port door.
2.
Lock/Unlock All - Single-click to lock
doors and trunks (all doors and trunks
must be closed). Double-click to unlock
doors and trunks.
3.
Front trunk - Double-click to unlatch the
front trunk.
Once inside, power up Model S by pressing
the brake pedal within two minutes of
pressing the unlock button on the key fob
(see
Starting and Powering Off on page 51).
If you wait longer than two minutes, you must
press the unlock button again, or place the key fob near the card reader located
in the lower half of the left wireless phone charger, facing downward, on the center console.
When your key fob is detected, the two
minute authentication period restarts.
When approaching or leaving Model S carrying the key fob, you do not need to point the key fob at Model S as you press a button,
but you must be within operating range.
Radio equipment on a similar frequency can affect the key. If this happens, move the key
at least one foot (30 cm) away from other
electronic devices (phones, laptops, etc.).
If the key fob does not work (for example, its
battery is dead), you can touch its flat side
against the card reader on the driver

Before folding, remove items from the seats
and the rear footwell. To allow the rear seats
to fold completely
flat, you may need to move
the front seats forward. To fold a rear seat,
push the corresponding button on the back
of the seat.
You can also fold the rear seats fully forward
by pressing the corresponding switch located on the left side of the rear trunk. Pressing the
switch causes the seat to unlatch. You can
then push it downward to lay it fully
flat.
To return the seats to their upright position,
pull upwards until it locks into place. To
confirm that the seat is locked in the upright
position, try pulling it forward.
NOTE: Driving with the rear seats folded may
increase noise in the cabin area (for example,
you may hear vibration sounds coming from
the rear of the vehicle such as the trunk, suspension, etc.).
CAUTION: While raising a rear seat back, hold the seat belt out of the way to ensure that the seat belt is not trapped behind the backrest or caught in the seat latch.
WARNING: Always ensure that the seats are locked in their upright position by attempting to push it forward or rearward, ensuring the latch is fully engaged. Failure to do so can increase the risk of injury.
Head Supports
The front seats include integrated head
supports that you cannot adjust.
The rear outboard seating positions include
an adjustable head support that can be raised/lowered or removed. The head support
should always be raised and locked into
position (so that the center is aligned with the
center of the ears) when occupied by a
passenger that is not in a child safety seat.
Lift the head support to the desired position. To lower the head support, press and hold the
button on the base of the outer post while
pushing down on the head support.
To remove a head support:
1.
Lift the headrest to raise it.
2.
Press and hold the button located at the
base of the right post.
3.
Insert a short, flat object (such as a small flat-head screwdriver) into the opening
on the inside base of the opposite post
and pull the head support upward.
Front and Rear Seats
27Seating and Safety Restraints

AreaLocationMeasurement (in)Measurement (mm)Leg RoomFront42.41,077Rear35.5901Shoulder RoomFront58.41,484Rear55.11,399Hip RoomFront54.81,393Rear50.31,278
Cargo Volume
AreaVolume (liters)Volume (cubic feet)Front trunk893.1Behind first row, second row folded flat1,73961.4Behind second row70925.0Maximum total cargo volume with driver and front
passenger1,82864.6Maximum total cargo volume with driver and 4
passengers79828.2
Weights
Refer to the certification label for mass data (see Identification Labels on page 203).
Dimensions and Weights
207Specifications