Fan TOYOTA 4RUNNER 1997 Owners Manual

38
Child restraint systems are classified into the following 3 types depending on the
child's age and size.
(A) Infant seat
(B) Convertible seat
(C) Booster seat
Install the child restraint system following the instructions provided by its manufac-
turer.
ÐTypes of child restraint system

39
(A) INFANT SEAT INSTALLATION
An Infant seat is used in rear-facing onlyCAUTION!
Do not use a rear-facing child rees- traint system in the rear seat if it in- terferes with the lock mechanism of
the front seats. This can cause se-
vere injury to the child and front pas-
senger in case of sudden braking ora collision.
1. Run the center lap and shoulder belt through or around the infant seat fol-
lowing the instructions provided by its
manufacturer and insert the tab into the buckle taking care not to twist the lap belt.
ÐInstallation with 2-point type seat belt

40
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and
that the lap and belt is not twisted.
Do not insert coins, clips, etc. in the
buckle as this may prevent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, it cannot protect your
child from injury. Contact your To-
yota dealer immediately. Do not
use the seat until the seat belt isfixed.
2. While pressing the infant seat firmly
against the seat cushion and seat-
back, tighten the lap belt by pulling its
free end to hold the infant seat secure-
ly.CAUTION!
Push and pull the child restraint
system is different directions to be
sure it is secure. Follow all the
installation instructions provided
by its manufacturer.

41
3. To remove the infant seat, press thebuckle-release button.(B) CONVERTIBLE SEAT INSTALLA-
TION
A convertible seats is used in forward-
facing and rear-facing depending on
the child's age and size. When instal-
ling, follow the manufacturer's in-
struction about the applicable child's
age and size as well as direction for
installing of a child restraint system.CAUTION!
Do not use a rear-facing child re-
straint system in the rear seat if it in-
terferes with the lock mechanism of
the front seats. This can cause se-
vere injury to the child and front pas-
senger in case of sudden braking ora collision.

43
CAUTION!
Push and pull the child restraint sys- tem is different directions to be sure
it is secure. Follow all the installation
instructions provided by its
manufacturer.
3. To remove the convertible seat, press the buckle-release button.(A) INFANT SEAT INSTALLATION
An infant seat is used in rear-facing
position only.
ÐInstallation with 3-point type seat belt

44
CAUTION!
Never use a rear-facing child re-
straint system in the front seat be-
cause the force of the rapid infla-
tion of the passenger airbag can cause severe injury to the child.Do not put a rear-facing child re-
straint system in the rear seat if
the child restraint system inter-
feres with the front seat lock
mechanism or with your proper
driving position. This can cause
severe injury to the child and front
passenger in case of sudden brak-
ing or a collision.1. Run the lap and shoulder belt through
or around the infant seat following the
instructions provided by its manufac-
turer and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

45
CAUTION!
After inserting the tab, make sure
the tab and buckle are locked and that the lap belt is not twisted.
Do not insert coins, clips, etc. in
the buckle as this may pervent you
from properly latching the tab and buckle.
If the seat belt does not function
normally, it cannot protect your
child from injury. Contact your To-
yota dealer immediately. Do not
use the seat until the seat belt isfixed.
2. Fully extend the shoulder belt to put it
in the lock mode. When the belt is then
retracted even slightly, it cannot be ex-
tended.
To hold the infant seat securely, makesure the belt is in the lock mode before let-
ting the belt to retract.3. While pressing the infant seat firmly against the seat cushion and seat-
back, let the shoulder belt retract as far
as it will go to hold the infant seat se-
curely.

46
CAUTION!
Make sure the seat belt is securely
locked. Also make sure the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instruc-
tions provided by its manufacturer.
4. To remove the infant seat, press the buckle-release button and allow the
belt to retract completely. The belt will
move freely again and be ready to work for an adult or older child passen-
ger.(B) CONVERTIBLE SEAT INSTALLA-
TION
A convertible seat is used in forward-
facing and rear-facing position de-
pending on the child's age and size. When installing, follow the manufac-
turer 's instructions about the applica-
ble child's age and size as well as di-
rection for installing of a child
restraint system.

1221. Air Intake Selector
2. Air Flow Selector
3. Temperature Selector
4. Fan Speed Selector
5. A/Cº Button (on some models)
Air conditioning systemÐ ÐControls

123
Fan speed selector
Move the lever to adjust the fan speedÐto the right to increase, to the left to de-crease.
Temperature selector
Move the lever to adjust the temperature Ðto the right to warm, to the left to cool.
Air flow selector
Move the l
ever to select the vents used for
air flow.
1. Panel ÐAir flows mainly from the in-
strument panel vents.
2. Bi-level ÐAir flows from both the floor
vents and the instrument panel vents.
3. Floor ÐAir flows mainly from the floor
vents.
4. Floor/Windshield ÐAir flows mainly
from the floor vents and windshield vents.
5. Windshield ÐAir flows mainly from
the windshield vents. For details about air flow selector settings, see the illustration after A/Cº button.
Vehicles with A/Cº button indicatorÐ
Moving the airflow selector lever to wind-
shield position turns on the defroster-
linked air conditioning. At this time, the
A/Cº button indicator comes on regard- less of whether or not the A/Cº button is pressed in. This is to clear up the front
view more quickly. When the A/Cº button is not pressed in, moving the air flow control lever to anoth-
er position turns off the air conditioning.