transmission TOYOTA 4RUNNER 1998 Owner's Manual

4RUNNER (1998)
CAUTION
Before driving, be sure the park-
ing brake is fully released and
the parking brake reminder light
is off.
Cruise control
The cruise control allows you to
cruise the vehicle at a desired
speed over 40 km/h (25 mph) even
with your foot off the accelerator
pedal.
Your cruising speed can be maintained
up or down grades within the limits of
engine performance, although a slight
speed change may occur when driving
up or down the grades. On steeper
hills, a greater s peed change will oc-
cur so it is better to drive without the
cruise control.
CAUTION
To help maintain maximum con-
trol of your vehicle, do not use
the cruise control when driving
in heavy or varying traffic, or
on slippery (rainy, icy or snow-
covered) or winding roads.
Avoid vehicle speed increases
when driving downhill. If the ve-
hicle speed is too fast in rela-
tion to the cruise control set
speed, cancel the cruise control
then downshift the transmission
to use engine braking to slow down.

4RUNNER (1998)
SETTING AT A DESIRED SPEED
On vehicles with automatic transmis-
sion, the transmission must be in ºDº
before you set the cruise control
speed.
Bring your vehicle to the desired
speed, push the lever down in the
ºSET/COASTº direction and release it.
This sets the vehicle at that speed. If
the speed is not satisfactory, tap the
lever up for a faster speed, or tap it
down for a slower speed. Each tap
changes the set speed by 1.6 km/h
(1.0 mph). You can now take your foot
off the accelerator pedal. If you need accelerationÐfor example,
when passingÐdepress the accelera-
tor pedal enough for the vehicle to
exceed the set speed. When you re-
lease it, the vehicle will return to the
speed set prior to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise con-
trol on, do not shift to neutral
without depressing the clutch
pedal, as this may cause engine
racing or overrevving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:a. Pulling the lever in the ºCANCELº
direction and releasing it.
b. Depressing the brake pedal.
c. Depressing the clutch pedal (manu- al transmission).
If the vehicle speed falls below about
40 km/h (25 mph), the preset speed
will automatically cancel out.
If the vehicle speed drops 16 km/h
(10 mph) below the preset speed, the
preset speed will also automatically
cancel out.

4RUNNER (1998)
To crank the engine without de-
pressing the clutch pedal, push the
switch with the ignition on.
The switch stays on as long as the
ignition is on. And it will automatically
turn off when the ignition is off.
This switch cancels the clutch start
system, which is desi gned to keep the
starter motor from operating if the
clutch pedal is not depressed all the
way down.
The switch allows the vehicle to be
driven out of difficult situations by
cranking the engine with the clutch engaged. Never use the switch for normal en-
gine starting. Be sure to follow the
starting procedure instructed in ºHow
to start the engineº in Part 3.
Clutch start cancel switch
(four- wheel drive models wi
manual transmission)

4RUNNER (1998)
CAUTION
Always observe the following pre-
cautions to minimize the risk of
serious personal injury or damage
to your vehicle: Avoid sharp turns or abrupt ma-
neuvers, if at all possible. As
with other vehicles of this type,
failure to operate this vehicle
correctly may result in loss of
control or vehicle rollover.
Avoid loading any items on the
roof that will make the center
of gravity even higher.
Always slow down in gusty
crosswinds. Because of its high
center of gravity, your vehicle
is more sensitive to side winds
than an ordinary passenger car.
Slowing down will allow you to
have much better control.
Do not drive horizontally across
steep slopes. Driving straight
up or straight down is pre-
ferred. Your vehicle (or any sim-
ilar off- road vehicle) can tip
over sideways much more easi-
ly than forward or backward.When driving off- road or in
rugged terrain, do not drive at
excessive speeds, jump the ve-
hicle, or strike objects, etc.
This may cause loss of control
or vehicle rollover. You are also
risking expensive damage to y-
our vehicle's suspension and
chassis.
Break- in period
Drive gently and avoid high speeds.
Your vehicle does not need an elabo-
rate break- in. But following a few sim-
ple tips for the first 1600 km (1000
miles) can add to the future economy
and long life of your vehicle:
Do not drive over 88 km/h (55
mph).
Run the engine at moderate speed
between 2000 and 4000 rpm.
Avoid full- throttle starts.
Try to avoid hard stops during the
first 300 km (200 miles).
Do not drive slowly with the manu-
al transmission in a high gear.
Do not drive for a long time at any
single speed, either fast or slow.
Do not tow a trailer during the first
800km (500miles).

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking

4RUNNER (1998)
(b) Starting the engine
Before starting the engine, be sure to
follow the instructions in º(a) Before
crankingº.
Normal starting procedure
The multiport fuel injection system/se-
quential multiport fuel injection system
in your engine automatically controls
the proper air- fuel mixture for starting.
You can start a cold or hot engine as
follows:
1. With your foot off the accelerator
pedal, crank the engine by turning the
key to ºSTARTº. Release it when the
engine starts.
2. After the engine runs for about 10
seconds, you are ready to drive.
If the weather is below freezing, let
the engine warm up for a few minutes
before driving.
If the engine stalls...
Simply restart it, using the correct
procedure given in normal starting.
If the engine will not startÐ
See ºIf your vehicle will not startº in
Part 4.
NOTICE
Do not crank for more than 30 seconds at a time. This mayoverheat the starter and wiringsystems.
Do not race a cold engine.
If the engine becomes difficult
to start or stalls frequently,have the engine checked im-mediately.
Always slow down in gusty cross-
winds. This will allow you much
better control.
Drive slowly onto curbs and, if
possible, at a right angle. Avoid
driving onto high, sharp- edged ob-
jects and other road hazards. Fail-
ure to do so can lead to severe
tire damage resulting in tire bursts.
When parking on a hill, turn the
front wheels until they touch the
curb so that the vehicle will not
roll. Apply the parking brake, and
place the transmission in ºPº (auto-
matic) or in first or reverse (manu-
al). If necessary, block the wheels.
Washing your vehicle or driving
through deep water may get the
brakes wet. To see whether they
are wet, check that there is no
traffic near you, and then press the
pedal lightly. If you do not feel a
normal braking force, the brakes
are probably wet. To dry them,
drive the vehicle cautiously while
lightly pressing the brake pedal
with the parking brake pulled. If
they still do not work safely, pull to
the side of the road and call a
Toyota dealer for assistance.
Tips for driving in various
conditions

4RUNNER (1998)
The driver and all passengers
should fasten their seat belts
whenever the vehicle is moving.
NOTICE
If driving through water, such
as when crossing shallowstreams, first check the depth of the water and the bottom of
the river bed for firmness. Driveslowly and avoid deep water.
Take all necessary safety mea-
sures to ensure that water dam-age to the engine or other com- ponents does not occur.
Water entering the engine airintake will cause severe engine
damage.
Water can wash the grease fromwheel bearings, causing rustingand premature failure, and mayalso enter the differentials,
transmission and transfer case,reducing the gear oil's lubrica-ting qualities.
Sand and mud that has accum-
lated in brake drums andaround brake discs may affectbraking efficiency and may dam-
age brake system components.
Always perform a maintenanceinspection after each day of
off- road driving that has takenyou through rough terrain,sand, mud, or water. For sche-
duled maintenance information,refer to the separate ºOwner's Manual Supplement/Maintenance
Scheduleº.
Winter driving tips
Make sure you have ethylene- glycol
antifreeze in the radiator.
NOTICE
Do not use alcohol type anti-freeze.
Check the condition of the battery
and cables.
Cold temperatures reduce the capacity
of any battery, so it must be in top
shape to provide enough power for
winter starting. Chapter 7- 3 tells you
how to visually inspect the battery.
Your Toyota dealer and most service
stations will be pleased to check the
level of charge.
Make sure the engine oil viscosity
is suitable for the cold weather.
See Chapter 7- 2 for recommended
viscosity. Leaving a heavy summer oil
in your vehicle during winter months
may cause harder starting. If you are
not sure about which oil to use, call
your Toyota dealerÐhe will be pleased
to help.
Keep the door locks from freezing.
Squirt lock de- icer or glycerine into
the locks to keep them from freezing.
To open a frozen lock, try heating the
key before inserting it.

4RUNNER (1998)
Use a washer fluid containing an
antifreeze solution.
This product is available at your Toyo-
ta dealer and most auto parts stores.
Follow the manufacturer 's directions
for how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because itmay damage your vehicle's paint.
Do not use your parking brake
when there is a possibility it could
freeze.
When parking, put the transmission
into ºPº (automatic) or into first or
reverse (manual) and block the rear
wheels. Do not use the parking brake,
or snow or water accumulated in and
around the parking brake mechanism
may freeze, making it hard to release.
Keep ice and snow from accumulat-
ing under the fenders.
Ice and snow built up under your
fenders can make steering difficult.
During bad winter driving, stop and
check under the fenders occasionally. Depending on where you are driv-
ing, we recommend you carry some
emergency equipment.
Some of the things you might put in
the vehicle are tire chains, window
scraper, bag of sand or salt, flares,
small shovel, jumper cables, etc.
Trailer towing
Your vehicle is designed primarily as
a passenger- and- load- carrying ve-
hicle. Towing a trailer will have an
adverse effect on handling, perfor-
mance, braking, durability and driving
economy (fuel consumption, etc.).
Your safety and satisfaction depend
on the proper use of correct equip-
ment and cautious driving habits. For
your safety and the safety of others,
you must not overload your vehicle or
trailer. Ask your local Toyota dealer
for further details before towing.
WEIGHT LIMITS
Before towing, make sure the total
trailer weight, gross combination
weight, gross vehicle weight, gross
axle weight and trailer tongue load
are all within the limits.
The total trailer weight and tongue
load can be measured with platform
scales found at a highway weighing
station, building supply company,
trucking company, junk yard, etc.

4RUNNER (1998)
TRAILER TOWING TIPS
When towing a trailer, your vehicle
will handle differently than when
not towing. The three main causes
of vehicle- trailer accidents are driv-
er error, excessive speed and im-
proper trailer loading. Keep these in
mind when towing:
Before starting out, check operation
of the lights and all vehicle- trailer
connections. After driving a short
distance, stop and recheck the
lights and connections. Before ac-
tually towing a trailer, practice turn-
ing, stopping and backing with a
trailer in an area away from traffic
until you learn the feel.
Backing with a trailer is difficult
and requires practice. Grip the bot-
tom of the steering wheel and
move your hand to the left to move
the trailer to the left. Move your
hand to the right to move the trail-
er to the right. (This procedure is
generally opposite to that when
backing without a trailer). Also, just
turn the steering wheel a little at
a time, avoiding sharp or prolonged
turning. Have someone guide you
when backing to reduce the risk of
an accident.
Because stopping distance may be
increased, vehicle- to- vehicle dis-
tance should be increased when
towing a trailer. For each 16 km/h
(10 mph) of speed, allow at least
one vehicle and trailer length bet-
ween you and the vehicle ahead.
Avoid sudden braking as you may
skid, resulting in jackknifing and
loss of control. This is especially
true on wet or slippery surfaces.
Avoid jerky starts or sudden accel-
eration. If your vehicle has a
manual transmission, prevent ex-
cessive clutch slippage by keeping
engine rpm low and not racing the
engine. Always start out in first
gear.
Avoid jerky steering and sharp
turns. The trailer could hit your ve-
hicle in a tight turn. Slow down
before making a turn to avoid the
necessity of sudden braking.
Remember that when making a
turn, the trailer wheels will be clos-
er than the vehicle wheels to the
inside of the turn. Therefore, com-
pensate for this by making a larger
than normal turning radius with y-
our vehicle.
Crosswinds and rough roads will
adversely affect handling of your
vehicle and trailer, causing sway.
Pay attention to the rear from time
to time to prepare yourself for be-
ing passed by large trucks or
buses, which may cause your ve-
hicle and trailer to sway. If swaying
happens, firmly grip the steering
wheel and reduce speed immedi-
ately but gradually. Never increase
speed. Steer straight ahead. If you
make no extreme correction with
the steering or brakes, the vehicle
and trailer will stabilize.
Be careful when passing other ve-
hicles. Passing requires consider-
able distance. After passing a ve-
hicle, do not forget the length of
your trailer and be sure you have
plenty of room before changing
lanes.
In order to maintain engine braking
efficiency, do not use fifth gear
(manual transmission) or overdrive
(automatic transmission).

4RUNNER (1998)
Because of the added load of the
trailer, your vehicle's engine may
overheat on hot days (at tempera-
tures over 30 C [85 F]) when go-
ing up a long or steep grade with
a trailer. If the engine coolant tem-
perature gauge indicates overheat-
ing, immediately turn off the air-
conditioning (if in use), pull off the
road and stop in a safe spot. Refer
to ºIf your vehicle overheatsº in
Part 4 of this manual.
Always place wheel blocks under
both the vehicle and trailer wheels
when parking. Apply the parking
brake firmly. Put the transmission
in Pº (automatic) or in first or re-
verse (manual). Avoid parking on a
slope with a trailer, but if it cannot
be avoided, do so only after per-
forming the following:
1. Apply the brakes and hold.
2. Have someone place wheel blocks under both the vehicle and trailer
wheels.
3. When the wheel blocks are in place, release your brakes slowly
until the blocks absorb the load.
4. Apply the parking brake firmly. 5. Shift into first or reverse (manual)
or ºPº (automatic) and turn off the
engine. When restarting out after parking on
a slope:
1. With the transmission in ºPº posi- tion (automatic) or the clutch pedal
depressed (manual), start the en-
gine. (With an automatic transmis-
sion, be sure to keep the brake
pedal depressed.)
2. Shift into gear.
3. Release the parking brake (also foot brake on automatic transmis-
sion vehicles) and slowly pull or
back away from the wheel blo cks.
Stop and apply your brakes.
4. Have someone retrieve the blo cks.
CAUTION
Do not exceed 72 km/h (45
mph) or the posted towing
speed limit, whichever is lower.
Because instab ility (swaying) of
a towing vehicle- trailer com-
bination usually increases as
the speed increases, exceeding
72 km/h (45 mph) may cause
loss of control.