clutch TOYOTA 4RUNNER 1998 Owners Manual

4RUNNER (1998)
1. Clutch start cancel switch
2. Headlight and turn signal
switch
3. Wiper and washer switches
4. Back window defogger switch
5. Emergency flasher switch
6. Clock
7. Cup holder
8. Air conditioning controls
9. Car audio
10. Ashtray 11. Cigarette lighter
12. Ignition switch
13. Cruise control switch
14. Rear differential lock switch
15. Instrument panel light con- trol knob
16. Power rear view mirror con- trol switch (without power
windows)
17. Power back window lock switch (without power win-
dows)

4RUNNER (1998)
Part 1
OPERATION OF
INSTRUMENTS
AND CONTROLSÐ
Chapter 1- 6
Ignition switch,
Transmission
and Parking brake
Ignition switch with steering
lock
Automatic transmission
Manual transmission
Four- wheel drive system
Rear differential look system

P ar k ing br ak e
Cruise control
Clutch start cancel switch
Ignition switch with steering lock

4RUNNER (1998)
(i) If you cannot shift the selector
lever out of ºPº position
If you cannot shift the selector lever
from the ºPº position even though the
brake pedal is depressed, use the
shift lock override lever. For instruc-
tions, see ºIf you cannot shift auto-
matic transmission selector leverº in
Part 4. Manual transmission
The shift pattern is as shown above.
Press the clutch pedal down fully
while shifting, and then release it
slowly. Do not rest your foot on the
pedal while driving, because it will
cause clutch trouble. And do not use
the clutch to hold the vehicle when
stopped on an uphill gradeÐuse the
parking brake.
Recommended shifting speeds
The transmission is fully synchronized
and upshifting or downshifting is easy.
For the best compromise between fuel
economy and vehicle performance,
you should upshift or downshift at the
following speeds:3RZ- FE engine

4RUNNER (1998)
Good driving practice
If it is difficult to shift into reverse,
put the transmission in neutral, re-
lease the clutch pedal momentarily,
and then try again.
When towing a trailer, in order to
maintain engine braking efficiency,
do not use the fifth gear.
CAUTION
Be careful when downshifting on
a slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is com-
pletely stopped before shiftinginto reverse.
Four- wheel drive systemÐ
(a) Front drive control (lev
type)

4RUNNER (1998)
SHIFTING BETWEEN ºH2º AND ºH4º
To shift from ºH2º to ºH4º, move
the front drive control lever.
This can be done when the vehicle is
stopped, or moving straight ahead at
speeds of 40km/h (25mph) or less.
You need not depress the clutch ped-
al. If you have trouble shifting, de-
press or release the accelerator pedal
momentarily while pushing the front
drive control lever.
CAUTION
Never move the front drive con-
trol lever if wheels are slipping.
Stop the slipping or spinning be-
fore shifting.
To shift from ºH4º to ºH2 º, simply
move the front drive control lever.
This can be done at any vehicle
speed. You need not depress the
clutch pedal.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse. With A.D.D.
To shift from ºH2º to ºH4º,
reduce
your speed to less than 80 km/h (50
mph) and move the front drive control
lever. You need not depress the clutch
pedal.
If you have trouble shifting in cold
weather, reduce your speed or stop
the vehicle and reshift.
CAUTION
Never move the front drive con-
trol lever if wheels are slipping.
Stop the slipping or spinning be-
fore shifting.
To shift from ºH4º to ºH2º, simply
move the front drive control lever.
This can be done at any vehicle
speed. You need not depress the
clutch pedal.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse. SHIFTING BETWEEN ºH4º AND ºL4º
To shift from ºH4º to ºL4,
stop the
vehicle or reduce your speed to less
than 8 km/h (5 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and move the front drive
control lever.
To shift from ºL4º to ºH4º, depress
the clutch pedal and move the front
drive control lever.
This can be done at any vehicle
speed.
(c) Shifting procedure (leve
r
type with manu
transmission)

4RUNNER (1998)
To lock the rear differential, push
the switch.
Be sure to stop the wheels before
locking the differential.
Vehicles with manual transmis-
sion'For easy locking, depress the
clutch pedal, push the lock switch and
slowly release the clutch pedal.
The indicator light will blink when the
switch is turned on. Wait a few se-
conds for the system to complete op-
eration. After the differential is locked,
the light will stop blinking and remain on. The anti- lock brake system does not
operate when the rear differential is
locked. It is normal operation for the
ºABSº warning light to be on at this
time.CAUTION

Do not lock the differential until
the wheels have stopped spin-
ning. Otherwise, the vehicle
may move in an unexpected
direction when the differential
lock is engaged, resulting in an
accident. This may also lead to
possible damage to differential
lock component parts.
Do not drive over 8 km/h (5
mph) when the differential is
locked.
To unlock the differential, push the
switch once again.
Unlock the differential as soon as the
vehicle moves out.

4RUNNER (1998)
SETTING AT A DESIRED SPEED
On vehicles with automatic transmis-
sion, the transmission must be in ºDº
before you set the cruise control
speed.
Bring your vehicle to the desired
speed, push the lever down in the
ºSET/COASTº direction and release it.
This sets the vehicle at that speed. If
the speed is not satisfactory, tap the
lever up for a faster speed, or tap it
down for a slower speed. Each tap
changes the set speed by 1.6 km/h
(1.0 mph). You can now take your foot
off the accelerator pedal. If you need accelerationÐfor example,
when passingÐdepress the accelera-
tor pedal enough for the vehicle to
exceed the set speed. When you re-
lease it, the vehicle will return to the
speed set prior to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise con-
trol on, do not shift to neutral
without depressing the clutch
pedal, as this may cause engine
racing or overrevving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:a. Pulling the lever in the ºCANCELº
direction and releasing it.
b. Depressing the brake pedal.
c. Depressing the clutch pedal (manu- al transmission).
If the vehicle speed falls below about
40 km/h (25 mph), the preset speed
will automatically cancel out.
If the vehicle speed drops 16 km/h
(10 mph) below the preset speed, the
preset speed will also automatically
cancel out.

4RUNNER (1998)
If the preset speed automatically can-
cels out other than for the above
cases, have your vehicle checked by
your Toyota dealer at the earliest op-
portunity.
RESETTING AT A FASTER SPEED
Push the lever up in the ºRES/ACCº
direction and hold it. Release the le-
ver when the desired speed is at-
tained. While the lever is held up, the
vehicle will gradually gain speed.
However, a faster way to reset is to
accelerate the vehicle and then push
the lever down in the ºSET/COASTº
direction.
RESETTING AT A SLOWER SPEED
Push the lever down in the ºSET/
COASTº direction and hold it. Release
the lever when the desired speed is
attained. While the lever is held down,
the vehicle speed will gradually de-
crease.
However, a faster way to reset is to
depress the brake pedal and then
push the lever down in the ºSET/
COASTº direction. On vehicles with automatic transmis-
sion, even if you turn off the overdrive
switch, with the cruise control on, en-
gine braking will not be applied be-
cause the cruise control is not can-
celled. To decrease the vehicle speed,
reset to a slower speed with the
cruise control lever or depress the
brake pedal. If you use the brake ped-
al, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by
pulling the control lever or by de-
pressing the brake pedal or clutch
pedal, pushing the lever up in the
ºRES/ACCº direction will restore the
speed set prior to cancellation.
However, once the vehicle speed falls
below about 40 km/h (25 mph), the
preset speed will not be resumed.
CRUISE CONTROL FAILURE WARN-
ING
If the ºCRUISEº indicator light in the
instrument cluster flashes when using
the cruise control, press the ºCRUISE
ON- OFFº button to turn the system
off and then press it again to turn it on.If any of the following conditions then
occurs, there is some trouble in the
cruise control system.
The indicator light does not comeon.
The indicator light flashes again.
The indicator light goes out after it
comes on.
If this is the case, contact your Toyo-
ta dealer and have your vehicle in-
spected.

4RUNNER (1998)
To crank the engine without de-
pressing the clutch pedal, push the
switch with the ignition on.
The switch stays on as long as the
ignition is on. And it will automatically
turn off when the ignition is off.
This switch cancels the clutch start
system, which is desi gned to keep the
starter motor from operating if the
clutch pedal is not depressed all the
way down.
The switch allows the vehicle to be
driven out of difficult situations by
cranking the engine with the clutch engaged. Never use the switch for normal en-
gine starting. Be sure to follow the
starting procedure instructed in ºHow
to start the engineº in Part 3.
Clutch start cancel switch
(four- wheel drive models wi
manual transmission)

4RUNNER (1998)
Part 3
STARTING AND
DRIVING
Before starting the engine
How to start the engine
Tips for driving in various
conditions
Off- road driving precautions
Winter driving tips
Tr ailer towing
How to save fuel and make
your
vehicle last longer, too
Before starting the engine
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, seat cushion angle, head re-
straint height and steering wheel
angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts. 1. Apply the parking brake firmly.
2. Turn off unnecessary lights and ac-
cessories.
3. Manual transmission: Press the
clutch pedal to the floor and shift
the transmission into neutral. Hold
the clutch pedal to the floor until
the engine is started. A starter
safety device will prevent the start-
er from operating if the clutch ped-
al is not fully depressed.
Automatic transmission: Put the
selector lever in ºPº. If you need to
restart the engine while the vehicle
is moving, put the selector lever in
ºNº. A starter safety device will pre-
vent the starter from operating if the
selector lever is in any drive position.
4. Automatic transmission only: De-
press the brake pedal and hold it
to the floor until driving off.
How to start the engineÐ
(a) Before cranking