engine TOYOTA 4RUNNER 2001 Owner's Guide

’01 4Runner_U (L/O 0008)
11 82001 4RUNNER (OM35768U)
Leave the system on during ordinary driv-
ing so that it can operate when needed.
When traction control is applied, the slip
indicator light blinks.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the traction
control system is in the selfcheck mode,
and does not indicate malfunction. When
the traction control system is operating,
you may feel vibration or noise of your
vehicle, caused by operation of the
brakes. This indicates the system is func-
tioning properly.
When getting the vehicle out of mud or
new snow, etc. the traction control system
will help operate to prevent the wheels
from spinning.
You can turn off the traction control
system by pushing the “TRAC OFF”
switch. The “TRAC OFF” indicator light
will come on. Pushing the “TRAC OFF”
switch a second time turns on the trac-
tion control system again and the
“TRAC OFF” indicator light will go off.
The traction control system will automati-
cally go on, and the “TRAC OFF” indicator
light will go off when you drive over 30
km/h (19 mph) even if the “TRAC OFF”
switch is pushed to cancel the traction
control system.If your wheels get stuck in a ditch or
when you are driving on a slippery or
bumpy surface, turn off the traction control
system because its function that controls
engine performance interferes with the
process of freeing your wheels.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1202001 4RUNNER (OM35768U)
The active traction control system auto-
matically helps control the spinning of
4 wheels (fourwheel drive mode) or
rear wheels (twowheel drive mode)
which may occur when accelerating on
slippery road surfaces, by controlling
the output of the brake and engine.
Thus, the system assists driver to con-
trol the driving power of 4 wheels
(fourwheel drive mode) or rear wheels
(twowheel drive mode).
When you turn the ignition switch on, the
active traction control system always turns
on automatically, and the slip indicator
light will come on. The indicator lights will
go off after about a few seconds.If the slip indicator light is left on after
the ignition is turn on, have your vehicle
checked by your Toyota dealer as soon as
possible.
When the active traction control is ap-
plied, the slip indicator light blinks.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the active
traction control system is in the self
check mode, and does not indicate mal-
function. When the traction control system
is operating, you may feel vibration or
noise of your vehicle, caused by operation
of the brakes. This indicates the system
is functioning properly.
When getting the vehicle out of mud or
new snow, etc. the active traction control
system will help operate to prevent the
wheels from spinning.Active traction control system failure
warning
These lights warn that when there is a
problem somewhere in the active traction
control system.
If the “VSC OFF” indicator light and “VSC/
TRAC” warning light come on, have your
vehicle checked by Toyota dealer as soon
as possible.
The lights will come on when the ignition
key is turned to “ON”, and will go off after
about a few seconds.
The lights may come on for 60 seconds
after the ignition key is turned to the “ON”
position. It is normal if they go out after
a while.
Active traction control
system
(fourwheel drive models)
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1222001 4RUNNER (OM35768U)
Vehicle skid control system
The vehicle skid control system helps
to provide comprehensive control of the
systems such as antilock brakes, trac-
tion control, engine control, etc. This
system automatically controls the out-
put of the brakes or engine to help
prevent the vehicle from skidding under
adverse condition.
When you turn the ignition switch on, the
slip indicator light will come on. The slip
indicator light will go off after about a few
seconds.
If the slip indicator light is left on after
the ignition is tuned on, have your vehicle
checked by your Toyota dealer as soon as
possible.If the vehicles is going to skid during
driving, the slip indicator light flashes and
an alarm sounds intermittently.
The vehicle skid control activates when
the vehicle speed is more than 15 km/h
(9 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the vehicle
stability control is in the selfcheck mode
and does not indicate a malfunction.Fourwheel drive models only—
This switch can function only when the
fourwheel drive system is selected.
You can turn off the vehicle skid con-
trol system by pushing the center dif-
ferential lock switch. The “VSC OFF”
and center differential lock indicator
lights will come on. Pushing the center
differential lock switch a second time
turns on the system again. The “VSC
OFF” and center differential lock indica-
tor lights will go off.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1232001 4RUNNER (OM35768U)
If your wheels get stuck in a ditch or
when you are driving on severe off road
and sand, turn off the vehicle skid control
system because its function that controls
engine performance interferes with the
process of freeing your wheels.
NOTICE
Make sure that the center differential
lock indicator light goes off before
normal driving.
Twowheel drive models
Fourwheel drive models
Vehicle skid control system failure
warning
These lights warn that when there is a
problem somewhere in the vehicle skid
control system, traction control system
(twowheel drive models), active traction
control system (fourwheel drive models).
If the “VSC/TRAC” warning light and
“TRAC OFF” (twowheel drive models) or
“VSC OFF” (fourwheel drive models) indi-
cator light come on, have your vehicle
checked by Toyota dealer as soon as pos-
sible. However, it is no problem that the
“VSC/TRAC” warning light comes on when
the brake actuator temperature becomes
high. (For details, see “Traction control
system” and “Active traction control sys-
tem” in this section.)
The “VSC/TRAC” warning light and “TRAC
OFF” (twowheel drive models) or “VSC
OFF” (fourwheel drive models) indicator
light will come on when the ignition key
is turned to “ON”, and will go off after
about a few seconds.
The lights may come on for 60 seconds
after the ignition key is turned to the “ON”
position. It is normal if they go out after
a while.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1252001 4RUNNER (OM35768U)
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down the grades. On steeper hills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION
To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TURNING ON THE SYSTEM
To operate the cruise control, press the
“CRUISE ONOFF” button. This turns the
system on. The indicator light in the
instrument panel shows that you can now
set the vehicle at a desired cruising
speed. Another press will turn the system
completely off.
CAUTION
To avoid accidental cruise control en-
gagement, keep the “CRUISE ON
OFF” switch off when not using the
cruise control.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1262001 4RUNNER (OM35768U)
SETTING AT A DESIRED SPEED
The transmission must be in “D” before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push the lever down in the “SET/COAST”
direction and release it. This sets the ve-
hicle at that speed. If the speed is not
satisfactory, tap the lever up for a faster
speed, or tap it down for a slower speed.
Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your
foot off the accelerator pedal.If you need acceleration—for example,
when passing—depress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:
a. Pulling the lever in the “CANCEL”
direction and releasing it.
b. Depressing the brake pedal.
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out.
If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.RESETTING TO A FASTER SPEED
Push the lever up in the “RES/ACC” direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held up, the vehicle will gradually
gain speed.
However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the “SET/COAST” direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the “SET/COAST”
direction and hold it. Release the lever
when the desired speed is attained. While
the lever is held down, the vehicle speed
will gradually decrease.
However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the “SET/COAST” direction.
Even if you turn off the overdrive switch,
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1652001 4RUNNER (OM35768U)
Air intake selector
Press the button to select the air source.
1. Recirculate—Recirculates the air inside
the vehicle.
2. Fresh—Draws outside air into the sys-
tem.
If the engine coolant temperature becomes
extremely high, RECIRCULATE mode will
automatically be selected. This is not a
malfunction. When the engine coolant tem-
perature is lowered, the previous mode
will resume.
To prevent fogging up of the windshield,
the air intake mode may change automati-
cally to FRESH depending on the condi-
tion of the air conditioning system.“A/C” button
To turn on the air conditioning, press the
“A/C” button. The “A/C” button indicator
will come on. To turn the air conditioning
off, press the button again.
If the “A/C” button indicator flashes, there
is a problem in the air conditioning system
and the air conditioning automatically
shuts off. If this happens, take your ve-
hicle to a Toyota dealer for service.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1752001 4RUNNER (OM35768U)
The vehicles sold in U.S.A., the tempera-
ture is indicated in degrees Fahrenheit,
while the vehicles sold in Canada, the
temperature is indicated in degrees Centi-
grade.
Cigarette lighter and ashtrays
Cigarette lighter and front ashtray
Rear ashtray
CIGARETTE LIGHTER
To use the cigarette lighter, press it in.
When it becomes heated, it automatical-
ly pops out ready for use.
If the engine is not running, the key must
be in the “ACC” position.
Do not hold the cigarette lighter pressed
in.
Use a Toyota genuine cigarette lighter or
equivalent for replacement.
ASHTRAY
To use the ashtray, pull it out.
When finished with your cigarette, thor-
oughly extinguish it in the ashtray to pre-
vent other cigarette butts from catching
fire. After using the ashtray, push it back
in completely.
To remove the ashtray, press down on the
lock spring plate and pull out.
CAUTION
To reduce the chance of injury in
case of an accident or sudden stop
while driving, always push the ash-
tray back in completely after using.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1762001 4RUNNER (OM35768U)
Power outlets
Instrument panel
Luggage compartment
The power outlets are designed for
power supply for car accessories.
The key must be in the “ACC” or “ON”
position for the power outlet to be used.
NOTICE
To prevent the fuse from being
blown, do not use the electricity
over the total vehicle capacity of
12V/120W.
To prevent the battery from being
discharged, do not use the power
outlets longer than necessary when
the engine is not running.
Close the power outlet lids when
the power outlets are not in use.
Inserting a foreign object other than
the appropriate plug that fits the
outlet, or allowing any liquid into
the outlet may cause electrical fail-
ure or short circuits.
Glove box
To use the glove box, do this.
To open: Pull the lever.
On some models, the glove box light will
come on when the glove box is open with
the instrument panel lights on.
To lock: Insert the master key and turn it
clockwise.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the glove box door
closed while driving.
ProCarManuals.com

’01 4Runner_U (L/O 0008)
1892001 4RUNNER (OM35768U)
INFORMATION BEFORE DRIVING YOUR
TOYOTA
Offroad vehicle precautions190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breakin period191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation in foreign countries193 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threeway catalytic converter194 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust cautions195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Facts about engine oil consumption195 . . . . . . . . . . . . . . . . . . . . . . . . . .
Twin ground electrode spark plugs196 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system197 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake pad wear limit indicators200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage stowage precautions201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your Toyota’s identification201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft prevention labels202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspension and chassis203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of tires203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2
ProCarManuals.com