radio TOYOTA AVALON 1996 Owners Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: AVALON, Model: TOYOTA AVALON 1996Pages: 202, PDF Size: 1.54 MB
Page 10 of 202
10
Locking operation
Unlocking operationYour vehicle has a wireless remote
control
system that can lock or unlock
all the doors from a distance within
approximately 1 m (3 ft.) of the outside
handle of the driver's door. When op-
erated within approximately 1 m (3 ft.)
of the trunk lid, this system also opens
the trunk lid.
To lock or unlock all the doors, push
the switches of the transmitter.
To lock: Push the LOCKº switch. All the
doors are locked simultaneously.
To unlock: Push the UNLOCKº switch
once to unlock the driver's door alone.
Pushing the switch twice within 5 seconds
unlocks all the doors simultaneously.
If any of the doors is not securely closed,
or if the key is in the ignition switch, locking
cannot be performed by the LOCKº
switch.
You have 30 seconds to open a door after
using the wireless unlock feature. If a door
is not opened by then, all the doors will be
automatically locked again.
If pushing the LOCKº or UNLOCKº
switch does not actuate the doors, and
you have checked the battery in the trans-
mitter, consult your Toyota dealer.
To open the trunk lid, push the trunk
lid open switch.
To open the trunk lid with the master key,
see Trunk lidº.
If the wireless remote control transmitter
does not operate from a normal distance:
Check the batteries in the transmitter.
To replace the batteries, see Replac-
ing transmitter batteriesº.
Check for closeness to a radio trans-
mitter such as a radio station or an air-
port which can interfere with normal
operation of the transmitter.
ÐWireless remote control
ProCarManuals.com
Page 37 of 202
36
Do not perform any of the followingchanges without consulting your
Toyota dealer. Such changes caninterfere with proper operation ofthe SRS airbag system in somecases.
Installation of electronic itemssuch as a mobile two-way radio,
cassette tape player or compactdisc player
Modification of the suspension
system
Modification of the front endstructure
Attachment of a grille guard (bullbar, kangaroo bar, etc.), snow-
plow, winches or any other equip-ment to the front end
Repairs made on or near the con-sole, steering column, steeringwheel or dashboard near the frontpassenger airbag
NOTICE
This SRS airbag system has a service re-
minder indicator to inform the driver of op-
erating problems. If either of the following
conditions occurs, this indicates a mal-
function of the airbags. Contact your To-
yota dealer as soon as possible to service
the vehicle.
The light does not come on when the
ignition key is turned to the ACCº or
ONº position, or remains on.
The light comes on while driving.In the following cases, contact your Toyo-
ta dealer as soon as possible:
The SRS airbags have been inflated.
The front part of the vehicle (shaded in
the illustration) was involved in an ac-
cident not of the extent to cause the
SRS airbags to inflate
The pad section of the steering wheel or
front passenger airbag cover (shaded in
the illustration) is scratched, cracked, or
otherwise damaged.
ProCarManuals.com
Page 62 of 202
61
It is dangerous to continue driving
normally when the brake fluid level
is low.CAUTION
!
If the brake fluid level is correct...
Have the warning system checked by
your Toyota dealer.
(b) Seat Belt Reminder Light and Buzzer
Once the ignition key is turned to ONº or
STARTº, the reminder light and buzzer
come on if the driver's seat belt is not fas-
tened. Unless the driver fastens the belt,
the light stays on and the buzzer stops af-
ter about 4 to 8 seconds.
(c) Discharge Warning Light
This light warns that the battery is being
discharged.
If it comes on while you are driving, there
is a problem somewhere in the charging
system.
The engine ignition will continue to oper-
ate, however, until the battery is dischar-
ged. Turn off the air conditioning, blower,
radio, etc., and drive directly to the near-
est Toyota dealer or repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken or loose.
(d) Low Oil Pressure Warning Light
This light warns that the engine oil pres-
sure is too low.
If it flickers or stays on while you are driv-
ing, pull off the road to a safe place and
stop the engine immediately. Call a Toyota
dealer or qualified repair shop for assis-
tance.
The light may occasionally flicker when
the engine is idling or it may come on brief-
ly after a hard stop. There is no cause for
concern if it then goes out when the en-
gine is accelerated slightly.
The light may come on when the oil level
is extremely low. It is not designed to indi-
cate low oil level, and the oil level must be
checked using the level dipstick.
NOTICE
Do not drive the vehicle with the warning light onÐeven for one
block. It may ruin the engine.
(e) Malfunction Indicator Lamp
This lamp comes on in the following
cases.
a. The fuel tank is completely empty.
(See Fuel gaugeº in Chapter 1-5 for in-
structions.)
b. The fuel tank cap is not tightened se-
curely. (See Fuel tank capº in Chapter
1-2 for instructions.)
c. There is a problem somewhere in your
engine or automatic transmission electri-
cal system.
If it comes on while you are driving in case
c, have your vehicle checked/repaired by
your Toyota dealer as soon as possible.
(f) Low Fuel Level Warning Light
This light comes on when the fuel level in
the tank becomes nearly empty. Fill up the
tank as soon as possible.
(g) ABSº Warning Light
This light warns that there is a problem
somewhere in your anti-lock brake sys-
tem.
If the light comes on while you are driving,
have your vehicle checked by your T oyota
dealer as soon as possible.
The light will come on when the ignition
key is turned to the ONº position. After
about 3 seconds, the light will go off.
ProCarManuals.com
Page 72 of 202
Part 1
71
OPERATION OF
INSTRUMENTS AND
CONTROLSÐ
Chapter 1-7
Car audio system
and Air conditioning
system
Car audio system
Reference
Using your audio system:
some basics
Using your audio system:
controls and features
CD (Compact Disc) Auto
changer
Anti-theft system
Car audio system operating
hints
Air conditioning system
Controls
Air flow selector settings
Operating tips
Instrumental panel vents
Type 1-1: AM.FM ETR radio/cassette
player
Type 1-2: AM.FM ETR radio/cassette
player
Type 1-3: AM.FM ETR radio/cassette
player
Type 2: AM.FM ETR radio/cassette
player/compact disc player
Car audio systemÐ
ÐReference
ProCarManuals.com
Page 73 of 202
72This section describes some of the basic
features on Toyota audio systems. Some
information may not pertain to your sys-
tem.
Your audio system works when the igni-
tion key is in the ACCº or ONº position.
TURNING THE SYSTEM ON AND OFF
Push PWR/VOLº to turn the audio sys-
tem on and off.
Push AM
.FMº, T
APEº, or CDº to turn on
that function without pushing PWR/
VOLº.
You can turn on the cassette player by in-
serting a cassette tape.
You can turn off the cassette player by
ejecting the cassette tape. If the audio
system was previously off, then the entire
audio system will be turned off when you
eject the cassette tape. If another function
was previously playing, it will come on
again.
SWITCHING BETWEEN FUNCTIONS
Push AM
.FMº, TAPEº or CDº if the sys-
tem is already on but you want to switch
from one function to another. TONE AND BALANCE
For details about your system's tone and
balance controls, see the description of
your own system.
Tone
How good an audio program sounds to
you is largely determined by the mix of the
treble, mid-range, and bass levels. In
fact, different kinds of music and vocal
programs
usually sound better with differ-
ent mixes of treble, mid-range, and bass.
Balance
A good balance of the left and right stereo
channels and of the front and rear sound
levels is also important.
Keep in mind that if you are listening to a
stereo recording or broadcast, changing
the right/left balance will increase the vol-
ume of one group of sounds while de-
creasing the volume of another. YOUR RADIO ANTENNA
To lower a power antenna, turn off the au-
dio system by pushing PWR/VOLº, or
turn the ignition key to LOCKº.
On some models, the power antenna au-
tomatically retracts when the radio mode
is switched off to turn on the cassette tape
player or compact disc player.
To prevent damage to the antenna,
make sure it is retracted before
driving your Toyota through anautomatic car wash.
NOTICE
YOUR CASSETTE PLAYER
When you insert a cassette, the exposed
tape should be to the right.
Do not oil any part of the player anddo not insert anything other than
cassette tapes into the slot, or thetape player may be damaged.
NOTICE
ÐUsing your audio system:
some basics
ProCarManuals.com
Page 78 of 202
77
1 2 3 4 5 6 (Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in the
desired station (see TUNE/SEEKº or
TUNEº). Push and hold down the button
until
you hear a beepÐthis will set the sta-
tion to the button. The button number will
appear on the display.
To tune in to a preset station: Push the
button for the station you want. The button
number and station frequency will appear
on the display.
Types 1-1 and 1-2ÐThese systems can
store one AM and one FM station for each
button. The preset station memory will be
canceled out if the power source is inter-
rupted (battery disconnected or fuse
blown).
Type 1-3ÐThis system can store one AM
and two FM stations for each button. (The
display will show AMº, FM1º, or FM2º
when you push AM
.FMº.) To cancel out
the preset station memory, push 1º, 2º,
and 3º at the same time and hold them in
until you hear a beep.
(Eject button)
Types 1-2 and 1-3
Push this button to eject a cassette.
After you turn the ignition to LOCKº, you
will be able to eject a cassette but you will
not be able to reinsert it.
AM
.FM
Push AM
.FMº to switch between the AM
and FM bands.
Types 1-1 and 1-2кAMº or FMº will ap-
pear on the display.
Type 1-3ÐAMº or FM1º, or FM2º will
appear on the display. These systems al-
low you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn on
the radio by pushing AM
.FMº. Also, push
AM.FMº to switch from cassette opera-
tion to radio operation. APS (Automatic program selection)
Type 1-3 only
The automatic program selection (APS)
feature allows you to program your cas-
sette player to skip forward or backward
to locate the song you want to hear. You
can skip up to nine tracks at a time.
Push
APSº. APSº AND 1º will appear on
the display.
Next, push APSº until the number on the
display reaches the number of tracks you
want to skip. If you push APSº ten times,
the APS feature will be turned off.
If you choose the number 1º, the play-
er will rewind to the beginning of the
current track.
When counting the number of tracks
you want to rewind, remember to
count the current track as well. For ex-
ample, if you want to rewind to a song
that is two before the song you are lis-
tening to, push APSº until 3º appears
on the display.
ProCarManuals.com
Page 80 of 202
79
FADE
This knob lets you adjust the balance be-
tween the front and rear speakers.
Type 1-1ÐPush BAL/FADEº so that it
pops out of its retracted position. Pull out
the knob. Turn the knob to adjust the front/
rear balance. Push the knob back into its
retracted position.
Types 1-2 and 1-3ÐMove the FADEº
ring around PWR/VOLº to adjust the
front/rear balance.
MTL (Metal) display
Types 1-2 and 1-3
If a metal or chrome equivalent cassette
tape is put in the cassette player, the play-
er will automatically adapt to it and MTLº
will appear on the display.
PROG (Program)
Push PROGº to select the other side of
a cassette tape. The display indicates
which side is currently selected (
~º indi-
cates top side, !º indicates bottom side).
Auto-reverse featureÐAfter the cassette
player reaches the end of a tape side, it
automatically reverses and begins to play
the other side. This is true whether the
cassette was playing or fast forwarding. PWR
.VOL (Power.Volume)
Type 1-1 only
Push PWR
.VOLº to turn the audio sys-
tem on and off. T urn the PWR/VOLº knob
to adjust the volume.
PWR/VOL (Power/Volume)
Types 1-2 and 1-3
Push PWR/VOLº to turn the audio sys-
tem on and off. T urn the PWR/VOLº knob
to adjust the volume.
Pull out and then turn PWR/VOLº to ad-
just the balance between the right and left
speakers. Move FADEº around PWR/
VOLº to adjust the front/rear balance.
REW/FF (Rewind/Fast forward)
Push the FFº side of the button to fast for-
ward a cassette tape. FFº will appear on
the display. Push the REWº side to re-
wind a tape. REWº will appear on the dis-
play.
To stop the tape while it is fast forwarding,
push FFº or TAPEº; to stop the tape
while it is rewinding, push REWº or
TAPEº. The tape will immediately begin
to play.
If a tape side rewinds completely, the cas-
sette player will stop and then play that
same side. If a tape fast forwards com-
pletely, the cassette player will play the
other side of the tape, using the auto-re-
verse feature. R
.M (Radio monitor)
Type 1-3 only
The radio monitor feature allows you to
listen to the radio while a cassette is being
rewound or fast forwarded.
Push R
.Mº. R.Mº will appear on the dis-
play. Any time you are rewinding or fast
forwarding a cassette tape, the radio will
play the station that was set most recent-
ly. (You can not change the radio station
unless you switch out of the cassette play-
er function.)
Push R
.Mº again to turn off the R.M fea-
ture.
RPT (Repeat)
Type 1-3 only
The repeat feature automatically replays
the current cassette.
Push RPTº while the track is playing.
RPTº will appear on the display. When
the track ends, it will automatically be re-
wound and replayed. This process will be
continued until you push the button again
to turn off the repeat feature.
There must be at least 3 seconds of blank
space between tracks in order for the re-
peat feature to work correctly.
ProCarManuals.com
Page 81 of 202
80SCAN
Types 1-2 and 1-3
Radio
You can either scan all the frequencies on
a band or scan only the preset stations for
that band.
To scan the preset stations: Quickly push
and release SCANº. If you hear a beep,
you held the button too long, and the radio
will scan all the frequencies. The radio will
tune in the next preset station up the
band, stay there for a few seconds, and
then move to the next preset station. To
select a station, push SCANº a second
time.
To scan all the frequencies: Push SCANº
until you hear a beep. The radio will find
the next station up the station band, stay
there for a few seconds, and then scan
again. To select a station, push SCANº a
second time.
Cassette Player
The cassette player scan feature is similar
to the radio scan feature and uses the
same button.
Push SCANº. SCANº will appear on the
display. The player will fast forward to the
next cassette track,
play it for 12 seconds,
and then scan again. To select a track,
push SCANº a second time. If the player
reaches the end of one side of a cassette
tape, it will continue scanning on the other
side.
SKIP
Type 1-3 only
The skip feature allows you to fast forward
past long stretches of blank tape. This is
especially useful at the end of cassettes.
Push SKIPº. SKIPº will appear on the dis-
play. The cassette player will keep track of
how much blank space it plays. Any time
it has played about 10 seconds of blank
tape, it will automatically fast forward to
the next track and begin to play.
Push the button a second time to turn off
the skip feature. ST (Stereo reception) display
Your radio automatically changes to ste-
reo reception when a stereo broadcast is
received. STº appears on the display. If
the signal becomes weak, the radio re-
duces the amount of channel separation
to prevent the weak signal from creating
noise. If the signal becomes extremely
weak, the radio switches from stereo to
mono reception.
TAPE
Push TAPEº to switch from radio opera-
tion to cassette operation. If the audio
system is off,
you can turn on the cassette
player by pushing TAPEº. In both cases,
a cassette must already be loaded in the
player.
TREB (Treble)
This knob lets you adjust the treble level.
Push BASS/TREBº so that it pops out of
its retracted position. Pull out the knob.
Turn the knob to adjust the treble. Push
the knob back into its retracted position.ProCarManuals.com
Page 82 of 202
81
TUNE/SEEK (type 1-1)
TUNE (types 1-2 and 1-3)
Tuning
Your Toyota has an electronic tuning radio
(ETR).
Push and release the
~º (up) or ! º
(down) side of TUNE/SEEKº or TUNEº
to step up or down the station band. If you
hear a beep, you held the button too long
and the radio will go into the seek mode.
Seeking
In the seek mode, the radio finds and
plays the next station up or down the sta-
tion band.
To seek a station, push and hold the ~ º or
! º side of TUNE/SEEKº or TUNEº until
you hear a beep. Do this again to find
another station.ProCarManuals.com
Page 83 of 202
82
Button display for radio/cassette tape
player/compact disc player
Type 2
ProCarManuals.com