CHECK TOYOTA AVALON 2000 User Guide
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2000, Model line: AVALON, Model: TOYOTA AVALON 2000Pages: 352, PDF Size: 3.15 MB
Page 104 of 352
'00 AVALON U (L/O9908)
103
CAUTION
Never put a rear- facing child re-
straint system on the front seat be-
cause the force of the rapid infla-
tion of the passenger airbag can
cause death or serious injury to the
child.
Same angle
Same
height
Move seat
fully back
Move seat
fully back
A forward- facing child restraint sys-
tem should be allowed to be put on
the front seat only when it is un-
avoidable. Always move the seat as
far back as possible, because the
force of the deploying airbag could
cause death or serious injury to the
child.
When installing a child restraint system in
the front seat center position, move the
driver and passenger seats as far back as
possible, set both seatbacks to the same
angle as the back of the child restraint
system, and set both seat cushions at the
same height so that the child restraint
system is securely restrained.
With the child restraint system installed,
check that your driving position is satis-
factory and that the child restraint system
does not interfere with your driving.
If your driving position is not satisfactory,
or the child restraint system interferes
with your driving, install it at another posi-
tion.
ProCarManuals.com
Page 108 of 352
'00 AVALON U (L/O9908)
107
2. Remove the anchor bracket coverwith the symbol mark shown in the
illustration.3. Fix the child restraint system withthe seat belt.
Latch the hook onto the anchor
bracket and tighten the top strap.
For instructions to install the child re-
straint system, see ºChild restraintº in this
section.
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
4. Replace the head restraint.
Store any removed covers in a safe place
such as the glove box.
Be sure to replace all covers when the
anchor bracket is not in use.
ProCarManuals.com
Page 144 of 352
'00 AVALON U (L/O9908)
143
(a)If parking brake
is off, stop
immediately and
contact Toyota
dealer.
(b) Fasten driver 's
seat belt.
If the indicator or
buzzer comes on...
(d) Stop and check. (type A)
(type B)
(indicator and buzzer)
(e) Stop and check.Do this.
(c) Fasten front
passenger 's seat
belt.
(h) Take vehicle to
Toyota dealer.
If brake system
warning light is
also on, stop
immediately and
contact Toyota
dealer.
If the indicator or
buzzer comes on...
(i) Close all doors.
(j) Replace bulb.
(type A)
(type B)
(g)
Fill up tank.
Do this.
(f) Take vehicle to
Toyota dealer.
(m) Take vehicle to
Toyota dealer.
If the indicator or
buzzer comes on...
(o) Remove key. Key reminder
buzzer
(n) Add washer fluid.Do this.
(l) Take vehicle to
Toyota dealer.
(k) Take vehicle to
Toyota dealer
immediately.
Service reminder indicators
an d warn in g bu zzers
ProCarManuals.com
Page 145 of 352
'00 AVALON U (L/O 9908)
144
(a) Brake System Warning Light
This light comes on in the following cases
when the ignition key is turned on.
When the parking brake is applied...
This light comes on for a few seconds
with the ignition on even after the parking
brake is released.
When the brake fluid level is low...
Have your vehicle checked at your
Toyota dealer in the following cases:
The light does not come on even if the
parking brake is applied with the igni-
tion ONº.
The light does not come on even if the
ignition key is turned on with the park-
ing brake released.
If the light lit during driving goes out and
does not come again, it is a normal op-
eration.
CAUTION
If either of the following conditions
occurs, immediately stop your vehicle
at a safe place and contact your To-
yota dealer.
The light does not go out even af-
ter the parking brake is released
during the engine running.
In this case, the brakes might be
failing and your st opping distance
will be longer. Depress the brake
pedal firmly and bring the vehicle
to an immediate stop.
The brake system warning light re-
mains on together with the ABSº
warning light.
In this case, the vehicle may be-
come harder to control or skid dur-
ing hard braking or braking on slip-
pery road surfaces.
(b) Driver's Seat Belt Reminder Light
and Buzzer
This light and buzzer remind you to
buckle up the driver's seat belt.
Once the ignition key is turned to ONº or
STARTº, the reminder light flashes and
buzzer sounds if the driver 's seat belt is
not fastened. Unless the driver fastens the
belt, the light keep flashing and the buzz-
er sounds for about 4 to 8 seconds. (c) Front outside Passenger 's Seat Belt
Reminder Light
This light reminds you to buckle up the
front outside passenger 's seat belt.
Once the ignition key is turned to ºONº or
ºSTARTº, the reminder light flashes if a
passenger sits in the front outside passen-
ger seat and does not fasten the seat
belt. Unless the front passenger fastens
the belt, the light stays on. This light re-
minds you to buckle up the front passen-
ger 's seat belt.
If luggage load is placed on the front
outside passenger seat, depending on its
weight and how it is placed on the seat,
built- in sensors in the seat cushion may
detect the pressure, causing the reminder
light to come on.
(d) Discharge Warning Light
This light warns that the battery is being
discharged.
If it comes on while you are driving, there
is a problem somewhere in the charging
system.
The engine ignition will continue to oper-
ate, however, until the battery is dis-
charged. Turn off the air conditioning,
blower, radio, etc., and drive directly to
the nearest Toyota dealer or repair shop.
ProCarManuals.com
Page 146 of 352
'00 AVALON U (L/O9908)
145
NOTICE
Do not continue driving if the enginedrive belt is broken or loose.
(e) Low Oil Pressure Warning Light
This light warns that the engine oil pres-
sure is too low.
If it flickers or stays on while you are
driving, pull off the road to a safe place
and stop the engine immediately. Call a
Toyota dealer or qualified repair shop for
assistance.
The light may occasionally flicker when
the engine is idling or it may come on
briefly after a hard stop. There is no
cause for concern if it then goes out when
the engine is accelerated slightly.
The light may come on when the oil level
is extremely low. It is not designed to
indicate low oil level, and the oil level
must be checked using the level dipstick.
NOTICE
Do not drive the vehicle with thewarning light onÐeven for one block.It may ruin the engine.
(f) Malfunction indicator lamp
This lamp comes on in the following
cases.
a. The fuel tank is completely empty. (See
Fuel gaugeº in Section 1- 5 for instruc-
tions.)
b. The fuel tank cap is not tightened se-
curely. (See Fuel tank capº in Section
1- 2 for instructions.)
c. There is a problem somewhere in your
engine or automatic transmission electrical
system.
If it comes on while you are driving in
case c, have your vehicle checked/re-
paired by your Toyota dealer as soon as
possible.
(g) Low Fuel Level Warning Light
This light comes on when the fuel level
in the tank becomes nearly empty. Fill up
the tank as soon as possible.
On inclines or curves, due to the move-
ment of fuel in the tank, the low fuel level
warning light may come on earlier than
usual. (h) ABSº Warning Light
The light comes on with the ignition key
turned to ONº. If the anti- lock brake sys-
tem and the brake assist system work
properly, the light goes out after a few
seconds. Thereafter, if either of the sys-
tems malfunctions, the light comes on.
When the ABSº warning light is on (and
the brake system warning light is off), the
anti- lock brake system, the brake assist
system, the traction control system and/or
the vehicle skid control system do/does
not operate, but the system still operate
conventionally.
When the ABSº warning light is on (and
the brake system warning light is off), the
anti- lock brake system does not operate
so that the wheels could lock up during
a sudden brake or braking on slippery
road surfaces.
If the following conditions occur, this
indicates a malfunction somewhere in
the parts monitored by the warning
light system. Contact your Toyota
dealer as soon as possible to service
the vehicle.
The light does not come on with the
ignition key turned to ONº, or remains
on.
The light comes on while driving.
ProCarManuals.com
Page 148 of 352
'00 AVALON U (L/O9908)
147
(m) VSC OFFº Indicator Light
The light warns that when there is a prob-
lem somewhere in the vehicle skid control
system or traction control system.
The light will come on when the ignition
key is turned to ONº, and will go off after
about a few seconds.
If the VSC OFFº indicator light comes on,
the vehicle skid control system and trac-
tion control system do not work. However,
as conventional braking operates when ap-
plied, there is no problem to continue your
driving.
If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle:
The VSC OFFº indicator light does not
come on after the ignition is turned to
on.
The VSC OFFº indicator light is left on
after the ignition is turned to on.
The VSC OFFº indicator light comes
on while driving without pushing VSC
OFFº switch.(n) Low Windshield Washer Fluid Level
Warning Light
The light warns that the windshield washer
fluid level is too low. Add washer fluid at
your earliest opportunity. (For instructions,
see Adding washer fluidº in Section 7- 3.)
(o) Key Reminder Buzzer
This buzzer reminds you to remove the
key when you open the driver 's door with
the ignition key in the ACCº or LOCKº
position. CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light and low windshield
washer fluid level warning light)
1. Apply the parking brake.
2. Open one of the doors. The open door warning light should
come on.
3. Close the door. The open door warning light should go
off.
4. Turn the ignition key to ACCº. The SRS warning light should come on.
It goes off after about 6 seconds.
5. Turn the ignition key to ONº, but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light and
SRS warning light should come on. The
ABSº, VSCº, VSC OFFº and slip indi-
cator lights go off after a few seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, either the bulb is burned out or the
circuit is in need of repair. Have it
checked by your Toyota dealer as soon as
possible.
ProCarManuals.com
Page 165 of 352
'00 AVALON U (L/O 9908)
164
Traction control system
The traction control system automatical-
ly helps control the spinning of the
front wheels which may occur when ac-
celerating on slippery road surfaces,
thus assisting driver to control the driv-
ing power of the front wheels.
Leave the system on during ordinary
driving so that it can operate when
needed. When traction control is ap-
plied, the slip indicator light blinks.
While the VSCº warning light and VSC
OFFº indicator light come on, the traction
control system cannot be operated.You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the traction
control system is in the self- check mode,
and does not indicate malfunction.
When the traction control system is oper-
ating, you may feel vibration or noise of
your vehicle, caused by operation of the
brakes. This indicates the system is func-
tioning properly.
When getting the vehicle out of mud or
new snow, etc. the traction control system
will help operate to prevent the wheels
from spinning.You can turn off the traction control
system by pushing the VSC OFFº
switch. The VSC OFFº indicator light
will come on. Pushing the VSC OFFº
switch a second time turns on the trac-
tion control system again and the VSC
OFFº indicator light will go off. At this
time, the vehicle skid control also turns
off and on simultaneously.
ProCarManuals.com
Page 167 of 352
'00 AVALON U (L/O 9908)
166
Vehicle skid control system
The vehicle skid control system helps
provide comprehensive control of the
systems such as an anti- lock brake
system, brake assist system, traction
control, engine control, etc. This sys-
tem automatically controls the output of
the brakes or engine to help prevent
the vehicle from skidding when corner-
ing on a slippery road surface or
abrupt steering wheel operation occurs.If the vehicles is going to skid during
driving, the slip indicator light flashes and
an alarm sounds intermittently.
The vehicle skid control system activates
when the vehicle speed is about more
than 15 km/h (9 mph).
While the VSCº warning light and VSC
OFFº indicator light come on, the vehicle
skid control system cannot be operated.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the vehicle
skid control is in the self- check mode and
does not indicate a malfunction.You can turn off the vehicle skid con-
trol system by pushing the VSC OFFº
switch. The VSC OFFº indicator light
will come on. Pushing the VSC OFFº
switch a second time turns the system
again and the VSC OFFº indicator light
will go off. At this time, the traction
control also turns off and on simulta-
neously.
When you turn the ignition switch on, this
system always turns on.
ProCarManuals.com
Page 171 of 352
'00 AVALON U (L/O 9908)
170
SETTING AT A DESIRED SPEED
The transmission must be in Dº before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push COAST SETº button and release it.
This sets the vehicle at that speed. If the
speed is not satisfactory, push RES ACCº
button for a faster speed, or push SET
COASTº button for a slower speed. Each
push changes the set speed by 1.6 km/h
(1.0 mph). You can now take your foot off
the accelerator pedal.If you need accelerationÐfor example,
when passingÐdepress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by any
of the following:
a. Depressing the brake pedal.
b. Push CANCELº button and releasing it.
c. Pushing ON/OFFº button.
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will be
automatically cancelled.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will be also automatically cancelled.
If the preset speed automatically cancels
out for any other reasons, have your ve-
hicle checked by your Toyota dealer at the
earliest opportunity.
RESETTING TO A FASTER SPEED
Push ºRES ACCº button and hold it. Re-
lease the button the desired speed is at-
tained. While the button is pushed, the
vehicle will gradually gain speed.
When the difference between the actual
vehicle speed and the set speed is less
than 5 km/h (3 mph), the set speed can
be increased 1.6 km/h (1 mph) each time
by pushing RES ACCº button quickly
within 0.6 seconds.
However, a faster way to reset is to ac-
celerate the vehicle and then push
COAST SETº button.
RESETTING TO A SLOWER SPEED
Push COAST SETº button and hold it.
Release the button when the desired
speed is attained. While the button is
pushed, the vehicle speed will gradually
decrease.
When the difference is 5 km/h (3 mph) or
more, the vehicle will cruise with its actu-
al speed. When the difference between the
actual vehicle speed and the set speed is
less than 5 km/h (3 mph), the set speed
can be lowered 1.6 km/h (1 mph) each
time by pushing COAST SETº button
quickly within 0.6 seconds.
ProCarManuals.com
Page 212 of 352
'00 AVALON U (L/O9908)
211
If you want to return the setting to RE-
CIRCULATE mode, press the air intake
selector button once again.
Press the A/Cº button for dehumidified
heating or cooling. This setting clears the
front view more quickly.
To heat the vehicle interior while de-
frosting the windshield, choose
floor/windshield air flow.
Side vents
If air flow control is not satisfactory, check
the side vents. The side vents may be
opened or closed as shown.
Air conditioning filter
Automatic air conditioning system
onlyÐThis air conditioning system has
a high efficient air refiner filter which
helps eliminate dust and pollen, thereby
increasing your driving confort.
The air conditioning filter is set behind the
glove box.
ProCarManuals.com