engine TOYOTA AVALON 2001 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 839 of 1897
- DIAGNOSTICSBODY CONTROL SYSTEM
DI-623
779 Author: Date:
2001 AVALON (RM808U)
HEADLIGHT AND TAILLIGHT SYSTEM (CANADA):
SymptomSuspect AreaSee page
Only one side headlight does not light.
1. Headlight bulb
2. HEAD LWR (LH, RH) fuse
3. Wire harness-
BE-9
IN-30
Headlight does not light.
1. Headlight bulb
2. Headlight control relay circuit
3. Light control switch circuit
4. Wire harness-
DI-635
DI-631
IN-30
ºLo-Beamº does not light.
1. Headlight bulb
2. HEAD LWR (LH, RH) fuse
3. Headlight control relay circuit
4. Headlight dimmer switch
5. Wire harness-
BE-9
DI-635
DI-631
IN-30
ºHi-Beamº does not light.
1. Headlight bulb
2. HEAD UPR (LH, RH) fuse
3. DRL fuse
4. D.R.L. relay No.2, 3 and 4 relay circuit
5. Headlight dimmer switch
6. Wire harness-
BE-9
BE-9
DI-668
DI-631
IN-30
ºFlashº does not light.
1. Headlight bulb
2. HEAD UPR (LH, RH) fuse
3. DRL fuse (R/B No.7)
4. D.R.L. relay No.2, 3 and 4 relay circuit
5. Headlight dimmer switch
6. Wire harness-
BE-9
BE-9
DI-668
DI-631
IN-30
Headlight does not light with engine running and light control SW
OFF.
1. DOME fuse
2. GAUGE fuse
3. DRL fuse
4. Parking brake switch circuit
5. Generator
6. Wire harnessBE-9
BE-9
BE-9
DI-670
CH-9
IN-30
Only one side taillight does not light.1. Bulb
2. Wire harness-
IN-30
Taillight does not light.
1. TAIL fuse
2. Taillight control relay circuit
3. Light control switch circuit
4. Body ECU
5. Wire harnessBE-9
DI-633
DI-631
IN-30
IN-30
Rear Combination light does not light.
1. Taillight bulb
2. Light failure sensor
3. Wire harness-
BE-53
IN-30
AUTO TURN OFF SYSTEM:
SymptomSuspect AreaSee page
ºAuto turn-off systemº does not operate.
1. Drivers door courtesy switch circuit
2. Driver door ECU
3. Multiplex communication circuit
4. Body ECUDI-639
DI-676
DI-718
IN-30
Page 845 of 1897
- DIAGNOSTICSBODY CONTROL SYSTEM
DI-621
777 Author: Date:
2001 AVALON (RM808U) B5-6 e B5-14
RLWBIgnition switch ON10 - 14 VB5 6 e B5 14
(ALTL e GND1)R-L e W-BEngine runningBelow 1 V
B5-7 e B5-14
(CLTE e GND1)Y-B e W-BAutomatic light control sensor communication circuit-
B5-8 e B5-14
(CLTS e GND1)LG e W-BAutomatic light control sensor communication circuit-
B5-9 e B5-14
(MPX3 e GND1)R-Y e W-BMultiplex communication circuit-
B5-10 e B5-14
(RRU e GND1)G-B e W-BRear right side power window UP operationBelow 1 V
B5-1 1 e B5-14GRWBPassenger seat belt unfastenedBelow 1 VB5 1 1 e B5 14
(PBEW e GND1)G-R e W-BPassenger seat belt fastened10 - 14 V
B5-13 e Body ground
(CLTC e Body ground)W-B e Body groundConstantBelow 1 V
B5-14 e Body ground
(GND1 e Body ground)W-B e -ConstantBelow 1 V
B5-16 e B5-14RWWBRear door closed10 - 14 VB5 16 e B5 14
(RCTY e GND1)R-W e W-BRear door openedBelow 1 V
B5-17 e B5-14GWBPassenger seat belt unfastenedBelow 1 VB5 17 e B5 14
(PBKL e GND1)G e W-BPassenger seat belt fastened10 - 14 V
B5-18 e B5-14LBWBLuggage compartment door opener switch is operatedBelow 1 VB5 18 e B5 14
(TKU e GND1)L-B e W-BLuggage compartment door opener switch is not operated10 - 14 V
B5-20 e B5-14
(CLTB e GND1)L e W-BAutomatic light control sensor communication circuit-
B5-21 e B5-14
(MPX4 e GND1)G-B e W-BMultiplex communication circuit-
B5-22 e B5-14
(RRD e GND1)R-B e W-BRear right side power window DOWN operationBelow 1 V
B5-23 e B5-14GWWBPassenger seat belt unfastenedBelow 1 VB5 23 e B5 14
(DBEW e GND1)G-W e W-BPassenger seat belt fastened10 - 14 V
B5-25 e B5-14RWBEach door closed10 - 14 VB5 25 e B5 14
(AJAR- e GND1)R e W-BEach door openedBelow 1 V
Page 860 of 1897
I13614
IDL 13
IDLOE725 ECMCruise Control ECU
Y
C15
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-575
731 Author: Date:
2001 AVALON (RM808U)
DTC 51 Idle Signal Circuit
CIRCUIT DESCRIPTION
When the idle switch is turned ON, a signal is sent to the ECU. The ECU uses this signal to correct the dis-
crepancy between the throttle valve position and the actuator position sensor value to enable accurate
cruise control at the set speed. If the idle switch is malfunctioning, problem symptoms also occur in the en-
gine, so also inspect the engine.
DTC No.Detection ItemTrouble Area
51Short in idle signal circuit.
Harness or connector between ECM and throttle position
sensor
Throttle position sensor
Harness or connector between cruise control ECU and ECM
Cruise control ECU
WIRING DIAGRAM
DI6L6-01
Page 866 of 1897
I13610
Cruise Control ECU
4
PI
R-B
W-B10
1D
IF17W-R
4 IG1 AM1Ignition Switch 2
W
AM1 GAUGE NO. 1
2 1
5
B-L1
ALTFL Block
1 B
FL MAIN
BatteryF8 2G1
F6 F10
1
1
2H
B 5
W-LW-L 1
43 3
1B1
1G
4
1C IG1 RERAY 4
4D13
4F4
M7 M64
4H17
4A17
GR-R
R-BGR-R Cruise Control
Indicator Light
(in Multi Display)
IG
C15
I15
2J/B No. 4 J/B No. 4
Driver Side J/B
Engine Room R/B No. 5
Engine Room J/B DI-592
- DIAGNOSTICSCRUISE CONTROL SYSTEM
748 Author: Date:
2001 AVALON (RM808U)
CRUISE MAIN Indicator Light Circuit
CIRCUIT DESCRIPTION
When the cruise control main switch is turned ON, CRUISE MAIN indicator light lights up.
WIRING DIAGRAM
DI090-28
Page 870 of 1897
I13611
Cruise Control ECU
9
B
Y-R
IG B 3 1
4IG1 RELAY
2
AM1 ECU-IG NO. 2
5 5
B-L
ALT FL Block
F6
B
FL MAIN
BatteryW-BW-B 1
2G
F8
W-B AA
J5
J/C 1 F101 1
1G
3
1B
1
2H13
1B
4
1C2
3C2
3D
7
IF1
7
3A20
3BGND
1W-B16 W-B WY-R
W-R42
I15Ignition Switch
C15
W-L
W-L
B-LIG1 AM1
2
1J/B No. 3
Driver Side J/B
Engine Room J/B
Engine Room R/B No. 5
J/B No. 3
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-587
743 Author: Date:
2001 AVALON (RM808U)
ECU Power Source Circuit
CIRCUIT DESCRIPTION
The ECU power source supplies power to the actuator and sensors, etc, when terminal GND and the cruise
control ECU case are grounded.
WIRING DIAGRAM
DI08X-15
Page 874 of 1897
AB0119
I00143
I00174
ON
O/D
(-) (+)
DI-582
- DIAGNOSTICSCRUISE CONTROL SYSTEM
738 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
1 Check operation of overdrive.
PREPARATION:
Test drive after engine warms up.
CHECK:
Check that overdrive ON e OFF occurs by operation of OD switch ON-OFF.
NG Check and repair electronically controlled
transmission (See page DI-158).
OK
2 Check voltage between terminal OD of harness side connector of cruise control
ECU and body ground.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Turn ignition switch ON.
(c) Disconnect the ECU connector.
CHECK:
Measure voltage between terminal OD of harness side connec-
tor of ECU and body ground.
OK:
Voltage: 10 - 14 V
NG Go to step 5.
OK
Page 875 of 1897
I00141
ECT
(-) (+)
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-583
739 Author: Date:
2001 AVALON (RM808U)
3 Check voltage between terminal ECT of cruise control ECU connector and body
ground (On test drive).
PREPARATION:
(a) Connect the ECU connector.
(b) Test drive after engine warms up.
CHECK:
Check voltage between terminal ECT of ECU connector and
body ground when OD switch is ON and OFF.
OK:
OD switch positionVoltage
ON8 - 14 V
OFFBelow 0.5 V
OK Proceed to next circuit inspection shown in
problem symptom table (See page DI-560).
NG
4 Check harness and connector between terminal ECT of cruise control ECU and
electronically controlled transmission solenoid (See page IN-30).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU.
5 Check harness and connector between terminal OD of cruise control ECU and
terminal OD1 of ECM (See page IN-30).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU (See
page IN-30).
Page 876 of 1897
I17550
Cruise Control ECU
D 3
W-B 2
Ignition Switch1 II1
1G
3
4 4
2 1C
1
F10
1
ALT FL Block
1
FL MAINBattery IG1AM1CCS
F6 F8W-L26
1 20
AM1 Y-RY-R
R-L
R-LR-L
R-Y23
3D20
3C20
3C7
R-LY-R 4C6
4C19
II14
10 DL 2
W-R W
4
27
IF15
5 2
1
1 1
2H
2G
B-L1C1
1B3
IG B IG1 Relay
GAUGE NO. 2 A/T Indicator Light
Translate ECU
*1: w/ Traction Control
*2: w/o Tranction Control*1*2
T5
P1C15
I15
W-L
D6
DiodeY-R
*3: Floor Shift
*4: Column ShiftJ/B No. 4
J/B No. 3
*4
*3
Driver Side J/B
Engine Room R/B No. 5
BEngine Room J/B DI-584
- DIAGNOSTICSCRUISE CONTROL SYSTEM
740 Author: Date:
2001 AVALON (RM808U)
Park/Neutral Position Switch Circuit
CIRCUIT DESCRIPTION
When the shift position is except D, a signal is sent from the park/neutral position switch to the ECU. When
this signal is input during cruise control driving, the ECU cancels the cruise control.
WIRING DIAGRAM
DI08V-15
Page 877 of 1897
Input SignalIndicator Light
Blinking Pattern
Turn PNP switch
OFF (Shift to posi-
tions except D )LightON
OFFSW ON
SW OFF
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-585
741 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
1 Check starter operation.
CHECK:
Check that the starter operates normally and that the engine starts.
NG Proceed to engine troubleshooting.
OK
2 Input signal check.
PREPARATION:
See input signal check on page DI-551.
CHECK:
Check the indicator light when shifting into positions except D.
OK:
The indicator light goes off when shifting into posi-
tions except D.
OK Proceed to next circuit inspection shown in
problem symptom table (See page DI-560).
NG
Page 890 of 1897
I13679
(a)
(a)(b)
No.Operation MethodCRUISE MAIN Indicator Light
Blinking PatternDiagnosis
1 Push SET/COAST switch ON
2Push RES/ACC switch ON
3Push CANCEL switch ON
Turn stop light switch ON
Depress brake pedal
Turn PNP switch OFF
(Shift to except D position)
4Drive at about 40 km/h
(25 mph)or higher
Drive at about 40 km/h
(25 mph) or below
LightON
OFF
LightON
OFF
LightON
OFFSwitch ON
Switch OFF
LightON
OFFSwitch OFF
Switch ONSET/COAST switch circuit
is normal
RES/ACC switch circuit
is normal
CANCEL switch circuit
is normal
Stop light switch circuit
is normal
PNP switch circuit is
normal
Vehicle Speed Sensor is
normal
LightON
OFF LightON
OFF
1sec.
0.25 sec.0.25 sec.
Turn clutch switch OFF
(Depress clutch pedal)Clutch switch circuit
is normal
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-555
711 Author: Date:
2001 AVALON (RM808U)
5. INPUT SIGNAL CHECK
HINT:
(1) For check No.1 ~ No.3:
Turn ignition switch ON.
(2) For check No.4:
Jack up the vehicle.
Start the engine.
Shift to D position.
(a) Push the control switch to SET/COAST or RES/ACC posi-
tion and hold it down or up.
(b) Push the main switch ON.
(c) Check that the CRUISE MAIN indicator light blinks twice
or 3 times repeatedly after 3 seconds.
(d) Push the SET/COAST or RES/ACC switch OFF.
(e) Operate each switch as listed in the table below.
(f) Read the blinking pattern of the CRUISE MAIN indicator
light.
(g) After performing the check, turn the main switch OFF.
HINT:
When 2 or more signals are input to the ECU, the lowest num-
bered code will be displayed 1st.