boot TOYOTA AVALON 2001 Service User Guide
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 1453 of 1897
B06519
B08672
No.2 Timing Belt CoverTiming Belt
Timing Belt Guide
No.2 Generator
Bracket RH Engine Mounting Bracket
Crankshaft
PulleyGasket
Engine Wire
Protector
RH Camshaft Timing Pulley
No.2 Idler Pulley
Crankshaft
Timing PulleyDust Boot
Timing Belt Plate Plate Washer
215 (2,200, 159)
43 (440, 32)
27 (280, 20)
Timing Belt TensionerN´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
28 (290, 21)
No.1 Timing Belt Cover
125 (1,300, 94)
*88 (900, 65)
LH Camshaft
Timing Pulley
No.1 Idler Pulley
34 (350, 25)
Precoated part
* For use with SST
125 (1,300, 94)
LU-6
- LUBRICATIONOIL PUMP
1231 Author: Date:
2001 AVALON (RM808U)
Page 1468 of 1897
MA01O-02
B08915
- MAINTENANCECHASSIS
MA-7
49 Author: Date:
2001 AVALON (RM808U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering wheel free-play (See page SR-8).
(b) Check the steering linkage for looseness or damage.
Check that:
Tie rod ends do not have excessive play.
Dust seals and boots are not damaged.
Boot clamps are not loose.
2. INSPECT SRS AIRBAG (See pages RS-15, RS-30)
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
4. INSPECT DRIVE SHAFT BOOTS
Check the drive shaft boots for clamp looseness, leakage or
damage.
5. INSPECT BALL JOINTS AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.
Jack up the front of the vehicle and place wooden
blocks with a height of 180 - 200 mm (7.09 - 7.87
in.) under the front tires.
Lower the jack until there is about half a load on the
front coil spring. Place stands under the vehicle for
safety.
Check that the front wheels are pointing straight
ahead, and block them with chocks.
Using a lever, pry up the end of the lower arm, and
check the amount of play.
Maximum ball joint vertical play: 0 mm (0 in.)
If there is play, replace the ball joint.
(b) Check the dust cover for damage.
6. CHECK TRANSAXLE FLUID
Visually check the transaxle for fluid leakage.
If leakage is found, check for the cause and repair.
7. REPLACE TRANSAXLE FLUID (See page DI-160)
Page 1530 of 1897
PP2EQ-01
PP-32
- PREPARATIONSUSPENSION AND AXLE
82 Author: Date:
2001 AVALON (RM808U)
SUSPENSION AND AXLE
SST (Special Service Tools)
09238-47012Water Pump Bearing Remover &
ReplacerFront suspension
09240-00020Wire Gauge SetFront drive shaft
09309-36010Transmission Rear Bearing
ReplacerFront drive shaft
09310-35010Countershaft Bearing ReplacerFront axle
09316-2001 1Transfer Bearing ReplacerFront drive shaft
09316-6001 1Transmission & Transfer Bearing
ReplacerFront axle
Front suspension
(09316-0001 1)Replacer Pipe
(09316-00041)Replacer ºCº
09506-35010Differential Drive Pinion Rear
Bearing ReplacerFront drive shaft
09520-00031Rear Axle Shaft PullerFront axle
09521-24010Drive Shaft Boot Clamping ToolFront drive shaft
09527-1701 1Rear Axle Shaft Bearing RemoverFront axle
Page 1541 of 1897
PP0V4-05
PP-42
- PREPARATIONSTEERING
92 Author: Date:
2001 AVALON (RM808U)
STEERING
SST (Special Service Tools)
09023-38200Union Nut Wrench 12mmPS gear
09023-38400Union Nut Wrench 14mmPS vane pump
PS gear
09249-63010Torque Wrench AdaptorPS vane pump
09521-24010Drive Shaft Boot Clamping ToolPS gear
09527-2001 1Rear Axle Shaft Bearing RemoverPS gear
09612-00012Rack & Pinion Steering Rack
Housing StandPS gear
09612-07010Main Shaft Retaining Ring
Remover & ReplacerTilt steering column
09612-2201 1Tilt Handle Bearing ReplacerPS gear
09612-24014Steering Gear Housing Overhaul
Tool SetPS gear
(09613-2201 1)Steering Rack Shaft Bushing
Puller
09616-0001 1Steering Worm Bearing Adjusting
SocketPS gear
09631-10021Rack Stopper WrenchPS gear
Page 1550 of 1897
SS0BL-04
SS-24
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE
140 Author: Date:
2001 AVALON (RM808U)
AUTOMATIC TRANSAXLE
SERVICE DATA
Line pressure (wheel locked)Engine idling
D position
R position
at stall (Throttle valve fully opened)
D position
R position
401 - 461 kPa (4.1 - 4.7 kgf/cm2, 58 - 66 psi)
804 - 882 kPa (8.2 - 9.0 kgf/cm2, 117 - 128 psi)
1,138 - 1,236 kPa (11.6 - 12.6 kgf/cm
2, 165 - 179 psi)
1,716 - 1,854 kPa (17.5 - 18.9 kgf/cm2, 249 - 269 psi)
Engine stall revolution2,325 - 2,775 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF)
N position
700 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)Between boot and face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Drive plate runoutMax.
Torque converter clutch runout Max.
Torque converter clutch installation distance0.3 mm (0.0118 in.)
0.20 mm (0.0079 in.)
More than 13.7 mm (0.539 in.)
Lock-up point(Throttle valve opening 5%)
3rd gear (O/D main switch OFF) Lock-up ON
Lock-up OFF
O/D gear Lock-up ON
Lock-up OFF
65 - 70 km/h (40 - 43 mph)
57 - 62 km/h (35 - 39 mph)
65 - 70 km/h (40 - 43 mph)
57 - 62 km/h (35 - 39 mph)
Shift schedule
D position
(Throttle valve fully opened) 1 "2
2 "3
3 "O/D
O/D "3
3 "2
2 "1
(Throttle valve fully closed) 3 "O/D
O/D "3
2 position
(Throttle valve fully opened) 1 "2
3 "2
2 "1
L position
(Throttle valve fully opened) 3 "2
2 "1
65 - 71 km/h (40 - 44 mph)
122 - 131 km/h (76 - 81 mph)
188 - 198 km/h (117 - 123 mph)
181 - 191 km/h (112 - 119 mph)
113 - 122 km/h (70 - 76 mph)
54 - 59 km/h (34 - 37 mph)
38 - 43 km/h (24 - 27 mph)
22 - 27 km/h (14 - 17 mph)
65 - 71 km/h (40 - 44 mph)
132 - 141 km/h (82 - 88 mph)
54 - 59 km/h (34 - 37 mph)
115 - 124 km/h (71 - 77 mph)
59 - 64 km/h (37 - 40 mph)
Page 1782 of 1897
Z19562
O-Ring
* For use with SST Non-reusable partRack Housing
No. 2 Grommet
Rack HousingRack Boot
Clip
Tie Rod End
Lock Nut
Rack End
Steering Rack Rack Housing
No. 2 Bracket Clamp
Claw Washer
Teflon Ring
Oil Seal
Wire
Oil Seal
Molybdenum disulfide lithium base grease
Power steering fluidCylinder End Stopper
Bushing Claw Washer Rack End
83 (850, 61)
*60 (610, 44)
Clamp Rack Boot Clip
Lock Nut Tie Rod End
74 (750, 54)
74 (750, 54)
N´m (kgf´cm, ft´lbf) : Specified torque
O-Ring
83 (850, 61)
*60 (610, 44)
SR-38
- STEERINGPOWER STEERING GEAR
1501 Author: Date:
2001 AVALON (RM808U)
Page 1784 of 1897
SR0EV-05
W04228
SST
F13587
SST
R00429
Matchmarks
W04230
R11644
Claw Washer
- STEERINGPOWER STEERING GEAR
SR-41
1504 Author: Date:
2001 AVALON (RM808U)
DISASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. SECURE PS GEAR ASSEMBLY IN VISE
Using SST, secure the PS gear assembly in a vise.
SST 09612-00012
2. REMOVE 2 TURN PRESSURE TUBES
(a) Using SST, remove the 2 turn pressure tubes.
SST 09023-38200
(b) Remove the 4 O-rings from the 2 turn pressure tubes.
3. REMOVE RH AND LH TIE ROD ENDS AND LOCK
NUTS
(a) Place matchmarks on the tie rod end and rack end.
(b) Loosen the lock nut, and remove the tie rod end and lock
nut.
(c) Employ the same manner described above to the other
side.
4. REMOVE RH AND LH CLIPS, RACK BOOTS AND
CLAMPS
(a) Using a screwdriver, loosen the clamp.
NOTICE:
Be careful not to damage the rack boot.
(b) Remove the clip and rack boot.
(c) Employ the same manner described above to the other
side.
HINT:
Mark the RH and LH rack boot.
5. REMOVE RH AND LH RACK ENDS AND CLAW WASH-
ERS
(a) Using a screwdriver and hammer, unstake the claw wash-
er.
NOTICE:
Avoid any impact on the steering rack.
Page 1796 of 1897
R11668
Brass Bar
R11669
W04223
2 mm
(0.79 in.)
or less
SST
R00429
Matchmarks SR-54
- STEERINGPOWER STEERING GEAR
1517 Author: Date:
2001 AVALON (RM808U)
(c) Using a brass bar and hammer, stake the claw washer.
NOTICE:
Avoid any impact on the steering rack.
(d) Employ the same manner described above to the other
side.
18. INSTALL RH AND LH RACK BOOTS, CLAMPS AND
CLIPS
(a) Ensure that the steering rack hole is not clogged with
grease.
HINT:
If the hole is clogged, the pressure inside the rack boot will
change after it is assembled and the steering wheel is turned.
(b) Install the rack boot, clip and a new clamp.
NOTICE:
Be careful not to damage or twist the rack boot.
(c) Using SST, tighten the clamp as shown in the illustration.
SST 09521-24010
(d) Employ the same manner described above to the other
side.
19. INSTALL RH AND LH TIE ROD ENDS AND LOCK NUTS
(a) Screw the lock nut and tie rod end onto the rack end until
the matchmarks are aligned.
(b) After adjusting toe-in, torque the lock nut (See page
SA-4).
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
(c) Employ the same manner described above to the other
side.
Page 1838 of 1897
W03094
SST
F02207
SA-10
- SUSPENSION AND AXLEFRONT AXLE HUB
1344 Author: Date:
2001 AVALON (RM808U)
6. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE
(a) Remove the cotter pin and nut.
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
(b) Using SST, disconnect the tie rod end from the steering
knuckle.
SST 09610-20012
7. DISCONNECT LOWER BALL JOINT FROM LOWER
SUSPENSION ARM
Remove the 2 nuts and bolt.
Torque: 127 N´m (1,300 kgf´cm, 94 ft´lbf)
8. REMOVE STEERING KNUCKLE WITH AXLE HUB
(a) Remove the 2 nuts and bolts on the lower side of the
shock absorber.
(b) Remove the steering knuckle with the axle hub.
NOTICE:
Be careful not to damage the boot and ABS speed sensor
rotor.
Page 1839 of 1897
SA0VX-02
F07396
Fender Apron Seal
Drive Shaft (RH)
32 (330, 24)Lock Bolt
Snap Ring
No. 2 Dust Deflector
Outbord Joint Shaft
Fender Apron Seal
Tie Rod End
49 (500, 36)
Cotter pin
Lock Cap
294 (3,000, 217)
Lower Suspension Arm
127 (1,300, 94)
Boot Clamp
Boot
Boot
Snap Ring
Tripod RH:
Inboard Joint Shaft
Snap Ring
Bearing
Snap Ring
Dust Cover LH:
Inboard Joint
Shaft
Dust Cover
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
Drive Shaft (LH)
- SUSPENSION AND AXLEFRONT DRIVE SHAFT
SA-15
1349 Author: Date:
2001 AVALON (RM808U)
FRONT DRIVE SHAFT
COMPONENTS