light TOYOTA AVALON 2001 Service User Guide
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 114 of 1897
AX0KE-01
D07994
D07996
D07997
Apply MP Grease
D07998
AX-28
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1318 Author: Date:
2001 AVALON (RM808U)
REASSEMBLY
1. INSTALL 4 COLLARS
2. INSTALL CUSHION
Install the 2 cushions with the 2 screws.
3. INSTALL SHIFT LEVER SUB-ASSEMBLY
(a) Install the shift lever sub-assembly with the control shaft.
(b) Support the control shaft, as shown in the illustration.
(c) Install a new spring nut to the control shaft by knocking
them lightly via the 10-mm seated nut.
4. INSTALL GROOVED PIN
(a) Apply MP grease on the compression spring, detent rod
and shift lever sub-assembly.
(b) Place the shift lever plate.
(c) Insert the grooved pin in the detent rod pin hole.
NOTICE:
Assemble the grooved pin to ensure that it fits into the
guide hole of the shift lever sub-assembly in parallel.
Take care not to insert the pin in the wrong direction
of the detent rod.
Page 116 of 1897
D08000
D07239
D07222
D07220
AX-30
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1320 Author: Date:
2001 AVALON (RM808U)
NOTICE:
Install the grooved pin into the groove of the shift lock unit
as shown in the illustration.
9. ASSEMBLE LOWER POSITION INDICATOR HOUSING
(a) Install the slide cover.
(b) Install the spring and shift lock release bottom.
(c) Install the control position indicator plate.
10. INSTALL LOWER POSITION INDICATOR HOUSING
Install the lower position indicator housing with the 4 screws.
11. INSTALL INDICATOR LIGHT
(a) Install the bulb and cap to the indicator light wire.
(b) Install the indicator light to the lower position indicator
housing.
12. ASSEMBLE SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Install the spring and shift lever knob to the shift lever
knob.
(b) Install the O/D main switch and O/D main switch cover to
the shift lever knob.
13. INSTALL SHIFT LEVER KNOB AND SHIFT LEVER
KNOB COVER
(a) Pass through the wire harness of the O/D main switch as
shown in the illustration and set it.
(b) Install the shift lever knob and shift lever knob cover to the
shift lever sub-assembly.
NOTICE:
When operating the shift lever sub-assembly, check that
excessive force is not applied to the wire harness of the
O/D main switch.
Page 121 of 1897
D08001
Cover
Control Position
Indicator Plate
Slide CoverShift Lever Knob
Compression Spring
Shift Lever Knob Button
Shift Lever Knob
Cover
O/D Main
Switch Cover Shift Lever Knob Sleeve
Lower Position Indicator Housing
Detent Rod
Compression
Spring Manual Detent
Spring
Shift Lock
Release Button
SpringCushion
Shift Lock Control Unit
O/D Main Switch Grooved Pin
Collar
Shift Lever Plate
Shift Lever Sub-assembly
Bulb
Spring Nut
Indicator Light Wire
Control Shaft Cap
Apply MP grease
Precoated part
Non-reusable part
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
AX-21
1311 Author: Date:
2001 AVALON (RM808U)
Page 123 of 1897
D07992
D07220
D07222
D07239
D07225
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
AX-25
1315 Author: Date:
2001 AVALON (RM808U)
(c) Insert a small screwdriver into the position in the illustra-
tion and disengage the claw.
(d) Remove the shift lever knob button and compression
spring.
4. REMOVE INDICATOR LIGHT
(a) Remove the indicator light from the lower position indica-
tor housing.
(b) Remove the cap and bulb from the indicator light wire.
5. REMOVE LOWER POSITION INDICATOR HOUSING
Remove the 4 screws and lower position indicator housing.
6. DISASSEMBLE LOWER POSITION INDICATOR
HOUSING
(a) Remove the control position indicator plate.
(b) Remove the shift lock release button and spring.
(c) Remove the slide cover.
7. REMOVE SHIFT LOCK CONTROL UNIT
Remove the 2 screws and shift lock control unit assembly.
Page 127 of 1897
AX0KE-01
D07994
D07996
D07997
Apply MP Grease
D07998
AX-28
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1318 Author: Date:
2001 AVALON (RM808U)
REASSEMBLY
1. INSTALL 4 COLLARS
2. INSTALL CUSHION
Install the 2 cushions with the 2 screws.
3. INSTALL SHIFT LEVER SUB-ASSEMBLY
(a) Install the shift lever sub-assembly with the control shaft.
(b) Support the control shaft, as shown in the illustration.
(c) Install a new spring nut to the control shaft by knocking
them lightly via the 10-mm seated nut.
4. INSTALL GROOVED PIN
(a) Apply MP grease on the compression spring, detent rod
and shift lever sub-assembly.
(b) Place the shift lever plate.
(c) Insert the grooved pin in the detent rod pin hole.
NOTICE:
Assemble the grooved pin to ensure that it fits into the
guide hole of the shift lever sub-assembly in parallel.
Take care not to insert the pin in the wrong direction
of the detent rod.
Page 129 of 1897
D08000
D07239
D07222
D07220
AX-30
- AUTOMATIC TRANSAXLEFLOOR SHIFT ASSEMBLY
1320 Author: Date:
2001 AVALON (RM808U)
NOTICE:
Install the grooved pin into the groove of the shift lock unit
as shown in the illustration.
9. ASSEMBLE LOWER POSITION INDICATOR HOUSING
(a) Install the slide cover.
(b) Install the spring and shift lock release bottom.
(c) Install the control position indicator plate.
10. INSTALL LOWER POSITION INDICATOR HOUSING
Install the lower position indicator housing with the 4 screws.
11. INSTALL INDICATOR LIGHT
(a) Install the bulb and cap to the indicator light wire.
(b) Install the indicator light to the lower position indicator
housing.
12. ASSEMBLE SHIFT LEVER KNOB SUB-ASSEMBLY
(a) Install the spring and shift lever knob to the shift lever
knob.
(b) Install the O/D main switch and O/D main switch cover to
the shift lever knob.
13. INSTALL SHIFT LEVER KNOB AND SHIFT LEVER
KNOB COVER
(a) Pass through the wire harness of the O/D main switch as
shown in the illustration and set it.
(b) Install the shift lever knob and shift lever knob cover to the
shift lever sub-assembly.
NOTICE:
When operating the shift lever sub-assembly, check that
excessive force is not applied to the wire harness of the
O/D main switch.
Page 137 of 1897
AX03T-04
D07231
Shift Lock Control Switch
Key Interlock Solenoid
Stop Light Switch Shift Lock Solenoid
Shift Lock Control ECU
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-17
1307 Author: Date:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Column Shift)
LOCATION
Page 139 of 1897
AX0CS-02
D07232
Key Interlock Solenoid
Stop Light Switch
Shift Lock Control
Unit Assembly
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Floor Shift)
AX-15
1305 Author: Date:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Floor Shift)
LOCATION
Page 142 of 1897
Q09982
AX03R-05
D07234
Q00270
Q057310.8 - 1.5 mm (0.031-0.059 in.)200 mm
(7.87 in.)
Q00270
AX-12
- AUTOMATIC TRANSAXLETHROTTLE CABLE
1302 Author: Date:
2001 AVALON (RM808U)
THROTTLE CABLE
ON-VEHICLE REPAIR
1. REMOVE BATTERY
2. REMOVE CRUISE CONTROL ACTUATOR
(a) Remove the 3 bolts and cruise control actuator.
(b) Disconnect the connector.
3. DISCONNECT THROTTLE CABLE FROM ENGINE
Disconnect the cable from the throttle linkage.
4. REMOVE PARK/NEUTRAL POSITION SWITCH
(See page AX-4)
5. REMOVE VALVE BODY
(See page AX-6)
6. REMOVE THROTTLE CABLE
(a) Remove the bolt and retaining plate.
(b) Pull out the cable from the transaxle case.
7. INSTALL THROTTLE CABLE
If the throttle cable is new, do the following operations (a) - (b).
(a) Bend the cable so there is a radius of about 200 mm (7.87
in.).
(b) Pull the inner cable lightly until slight resistance is felt, and
hold it there.
(c) Stake the stopper, 0.8-1.5 mm (0.031-0.059 in.) from the
end of outer cable.
(d) Install a new O-ring to the throttle calbe.
(e) Make sure to push it in all the way.
(f) Install the retaining plate and bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
8. INSTALL VALVE BODY (See page AX-6)
Page 153 of 1897
I14591
Connector ºAºConnector ºBº Radio Receiver Side
Connector ºCº
- BODY ELECTRICALAUDIO SYSTEM
BE-163
1767 Author: Date:
2001 AVALON (RM808U)
2. INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Connect the connectors from the radio receiver assembly, and
inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
A1 - Ground
(FR+)Audio sounding5 - 7 V
A2 - Ground
(FL+)Audio sounding5 - 7 V
A3 - Ground
(ACC, +B)Ignition switch ACCBattery positive voltage
A4 - Ground
(BU +B)ConstantBattery positive voltage
A5 - Ground
(FR-)Audio sounding5 - 7 V
A6 - Ground
(FL-)Audio sounding5 - 7 V
A7 - Ground
(GND)ConstantContinuity
A8 - Ground
(ANT +B)Radio power switch ONBattery positive voltage
A10 - Ground
(ILL+)Headlight dimmer switch ONBattery positive voltage
B1 - Ground
(RR+)Audio sounding5 - 7 V
B2 - Ground
(RL+)Audio sounding5 - 7 V
B3 - Ground
(RR-)Audio sounding5 - 7 V
B4 - Ground
(RL-)Audio sounding5 - 7 V
C1 - Ground
(+B)ConstantBattery positive voltage
C2 - Ground
(ILL+)Hesdlight dimmer switch ONBattery positive voltage
C3 - Ground
(AMP+)Rasio switch ONBattery positive voltage
C7 - Ground
(MUTE)Audio sounding1V or below