brake TOYOTA AVALON 2001 Service Repair Manual

SA0VW-02
W03096
SST
W03097
WasherNut SA-14
- SUSPENSION AND AXLEFRONT WHEEL HUB BOLT
1348 Author
: Date
:
2001 AVALON (RM808U)
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using SST and a hammer handle or an equivalent, remove the
hub bolt.
SST 09628-1001 1
4. INSTALL HUB BOLT
(a) Install a washer and nut to a new hub bolt, as shown in the
illustration.
(b) Using a hammer handle or an equivalent to hold, install
the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 107 N´m (1,090 kgf´cm, 79 ft´lbf)
6. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)

SA0ER-03
F08681
Rear Axle CarrierNo.2 Lower
Suspension Arm
Brake Caliper
Rear Axle Hub Hub Bolt
Strut Rod ABS
Speed Sensor No.1 Lower
Suspension Arm
O-Ring
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part
Disc

Reused Nut : 196 (2,000, 145)
New Nut : 255 (2,600, 188)
80 (820, 59)
181 (1,850, 134)
47 (475, 34)
8.0 (82, 71 in.´lbf)
113 (1,150, 83)
SA-44
- SUSPENSION AND AXLEREAR AXLE HUB
1378 Author
: Date
:
2001 AVALON (RM808U)
REAR AXLE HUB
COMPONENTS

SA0W6-02
R10948
Z00206
W03211
A
A
B
- SUSPENSION AND AXLEREAR AXLE HUB
SA-45
1379 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the brake caliper and disc.
Torque: 47 N´m (475 kgf´cm, 34 ft´lbf)
(b) Support the brake caliper securely.
3. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator, check the backlash near the center
of the axle hub.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the axle hub.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.07 mm (0.0028 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. DISCONNECT ABS SPEED SENSOR
Remove the bolt and disconnect the ABS speed sensor.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
5. REMOVE REAR AXLE HUB
(a) Remove the 4 bolts and rear axle hub.
Torque: 80 N´m (820 kgf´cm, 59 ft´lbf)
(b) Remove the O-ring.
HINT:
At the time of installation, coat a new O-ring with MP grease.
(c) Support the backing plate securely.
6. REMOVE REAR AXLE CARRIER
(a) Loosen the 3 nuts.
Torque:
Nut A (Reused nut): 196 N´m (2,000 kgf´cm, 145 ft´lbf)
Nut A (New nut): 255 N´m (2,600 kgf´cm, 188 ft´lbf)
Nut B: 181 N´m (1,850 kgf´cm, 134 ft´lbf)

SA0VF-02
F07385
N´m (kgf´cm, ft´lbf) : Specified torque
Non-reusable part

38 (390, 28)
51 (520, 38)
51 (520, 38)
56 (570, 41)
181 (1,850, 134)
19 (195, 14)
181 (1,850, 134)
113 (1,150, 83)
5.4 (55, 48 in.´lbf)
113 (1,150, 83)
43 (440, 32)
Suspension Member Lower Stopper Suspension Member Lower Stopper
Suspension Member
Adjusting
TubeStabilizer
Bar Bracket
Suspension
Arm Washer
No. 2 Lower Suspension Arm
No. 1 Lower Suspension Arm
Parking Brake Cable
Strut Rod
Heated Oxygen
Sensor

Gasket Tailpipe
Center Exhaust Pipe

GasketSuspension Member Upper Stopper43 (440, 32)
SA-56
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
1390 Author
: Date
:
2001 AVALON (RM808U)
REAR LOWER SUSPENSION ARM AND STRUT ROD
COMPONENTS

SA0VG-02
W03216
W03217
Rear
F06465A
A B
B
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
SA-57
1391 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE CENTER EXHAUST PIPE
3. REMOVE STRUT ROD
(a) Remove the bolt and disconnect the parking brake cable.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the 2 bolts and nuts.
Torque: 113 N´m (1,150 kgf´cm, 83 ft´lbf)
NOTICE:
Do not turn the nut.
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolts.
(c) Remove the strut rod.
4. REMOVE NO. 2 LOWER SUSPENSION ARM
(a) Remove the 3 nuts, suspension arm washer and washer.
Torque: 181 N´m (1,850 kgf´cm, 134 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.
(b) Remove the No. 2 lower suspension arm.
HINT:
At the time of installation, face the paint mark to the rearward.
5. REMOVE STABILIZER BAR BRACKETS
(See page SA-63)
6. REMOVE NO. 1 LOWER SUSPENSION ARM
(a) Support the suspension member with a jack.
(b) Remove the 4 nuts, 2 bolts and 8 suspension member
stoppers.
Torque:
A: 51 N´m (520 kgf´cm, 38 ft´lbf)
B: 38 N´m (390 kgf´cm, 28 ft´lbf)
(c) Lower the suspension member.

SA0W8-02
Z00212
SST
Z00213
Nut
Washer
SA-48
- SUSPENSION AND AXLEREAR WHEEL HUB BOLT
1382 Author
: Date
:
2001 AVALON (RM808U)
REAR WHEEL HUB BOLT
REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using SST and a hammer handle or an equivalent, remove the
hub bolt.
SST 09628-1001 1
4. INSTALL HUB BOLT
(a) Install a washer and nut to a new hub bolt as shown in the
illustration.
(b) Using a hammer handle or an equivalent to hold, install
the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 47 N´m (475 kgf´cm, 34 ft´lbf)
6. INSTALL REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)