ESP TOYOTA AVALON 2001 Service Owner's Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 757 of 1897
Q04869
NC2 Revolution Sensor
D07907
E4
E4 1O1 2
G R
Direct Clutch
Speed Sensor24
NC2+
ECM
NC2
-
23
- DIAGNOSTICSAUTOMATIC TRANSAXLE
DI-193
349 Author: Date:
2001 AVALON (RM808U)
DTC P1705 NC2 Revolution Sensor Circuit Malfunction
(Direct Clutch Speed Sensor)
CIRCUIT DESCRIPTION
This sensor detects the rotation speed of the direct clutch drum.
By comparing the direct clutch speed signal with the vehicle
speed sensor signal, the ECM detects the shift timing of the
gears and appropriately controls the engine torque and hydrau-
lic pressure in response to various conditions, thus performing
smooth gear shifting.
DTC No.DTC Detecting ConditionTrouble Area
P1705
The ECM detects conditions (a), (b), (c), (d), (e) and (f) conti-
nuity for 4 secs. or more.
(2-trip detection logic)
(a) Gear change not being performed
(b) Gear position: 1st, 2nd 3rd or O/D
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1,000 rpm or more
(e) Park/neutral position switch: OFF
(f) Shift solenoid valves No. 1, No. 2, SL and vehicle speed
sensor are in normal operation.
Open or short in direct clutch speed sensor circuit
Direct clutch speed sensor
ECM
WIRING DIAGRAM
DI02P-07
Page 782 of 1897
Q00224
- DIAGNOSTICSAUTOMATIC TRANSAXLE
DI-171
327 Author: Date:
2001 AVALON (RM808U)
8. MANUAL SHIFTING TEST
HINT:
With this test, it can be determined whether the trouble is within
the electrical circuit or is a mechanical problem in the transaxle.
(a) Disconnect the solenoid wire.
(b) Inspect the manual driving operation.
Check that the shift and gear positions correspond with
the table below.
While driving, shift through the L, 2 and D positions.
Check that the gear change corresponds to the shift posi-
tion.
Shift PositionGear Position
DO/D
2O/D
L1st
RReverse
PPawl Lock
HINT:
If the L, 2 and D position gear positions are difficult to positions
are difficult to distinguish, do the above read test.
If any abnormality is found in the above test, the problem is in
the transaxle itself.
(c) Connect the solenoid wire.
(d) Cancel out the DTC (See page DI-160).
Page 891 of 1897
DI08L-15
DI-560
- DIAGNOSTICSCRUISE CONTROL SYSTEM
716 Author: Date:
2001 AVALON (RM808U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSuspect AreaSee page
SET not occourring or CANCEL occurring.
(DTC is Normal)
1. Vehicle Speed Sensor
2. Control Switch Circuit (Cruise control switch)
3. Stop Light Switch Circuit
4. Park/Neutral Position Switch Circuit
5. Actuator Motor Circuit
6. Cruise Control Cable
7. Cruise Control ECUDI-568
DI-572
DI-578
DI-584
DI-561
DI-596
IN-30
SET not occurring or CANCEL occurring.
(DTC dose not output)1. ECU Power Source Circuit
2. Cruise Control ECUDI-587
IN-30
Actual vehicle speed deviates above or below the set speed.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Electronically Controlled Transmission
Communication Circuit
4. Actuator Motor Circuit
5. Idle Signal Circuit (Main throttle position sensor)
6. Cruise Control ECUDI-596
DI-568
DI-581
DI-581
DI-561
DI-575
IN-30
Gear shifting frequent between 3rd O/D when driving on uphill
road. (Hurting)1. Electronically Controlled Transmission
Communication Circuit
2. Cruise Control ECUDI-581
DI-581
IN-30
Cruise control not cancelled, even when brake pedal is de-
pressed.
1. Cruise Control Cable
2. Stop Light Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI-596
DI-578
DI-561
IN-30
Cruise control not cancelled, even when transmission is shifted to
ºNº postion.
1. Cruise Control Cable
2. Park/Neutral Position Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI-596
DI-584
DI-561
IN-30
Control switch does not operate.
(SET/COAST, ACC/RES, CANCEL not possible)
1. Cruise Control Cable
2. Control Switch Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI-596
DI-572
DI-561
IN-30
SET possible at 40 km/h (25 mph) or less, or CANCEL does not
operate at 40 km/h (25 mph) or less.
1. Cruise Control Cable
2. Vehicle Speed Signal Abnormal
3. Actuator Motor Circuit
4. Cruise Control ECUDI-596
DI-568
DI-561
IN-30
Poor response is in ACCEL and RESUME modes.
1. Cruise Control Cable
2. Electronically Controlled Transmission
Communication Circuit
3. Actuator Motor Circuit
4. Cruise Control ECUDI-596
DI-581
DI-581
DI-561
IN-30
O/D does not resume, even though the road is not uphill.
1. Electronically Controlled Transmission
Communication Circuit
2. Cruise Control ECUDI-581
DI-581
IN-30
DTC memory is erased.1. Cruise Control ECUIN-30
DTC is not output, or is output when should not be.1. Diagnosis Circuit
2. Cruise Control ECUDI-594
IN-30
Cruise MAIN indicator light remains ON or falls to light up.1. Cruise MAIN Indicator Light Switch CircuitDI-592
Page 904 of 1897
A06092
1
3
5
24
6 IACV No.2IACV No.1, No.2 closed (VSV: OFF)
Throttle Valve30°
3,700 rpm
Engine Speed
Throttle Valve
Opening Angle
FI7011 FI6570
IACV No.1
2,700 rpmIACV No.1 open (VSV: ON)
IACV No.2 closed (VSV: OFF)
IACV No.1, No.2 open (VSV: ON)
A11667
From BatteryEngine Room J/B
2B 2G
2F
2B
2
4
1 EFI
No.1EFI Relay
W-B
B-W 9
E01ACISE4 R-Y
2 VSV for ACIS No.1
ED17
L-O B
4 EFI
No.21
2
From
Terminal
MREL of
ECME01
ACI1E5 15
B-W B-WECM
VSV for ACIS No.2W-R 1 2
53
- DIAGNOSTICSENGINE
DI-145
301 Author: Date:
2001 AVALON (RM808U)
IACV Control Circuit
CIRCUIT DESCRIPTION
This circuit opens and closes the IACV (Intake Air Control Valve) in response to the engine load in order to
increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is 3,700 rpm or less and the throttle valve opening angle is 30° or more, the ECM
turns the two VSV ON or OFF and operate the IACV.
WIRING DIAGRAM
DI08E-09
Page 990 of 1897
- DIAGNOSTICSENGINE
DI-1 11
267 Author: Date:
2001 AVALON (RM808U)
DTC P1133 A/F Sensor Circuit Response Malfunction
(Bank 1 Sensor 1)
DTC P1153 A/F Sensor Circuit Response Malfunction
(Bank 2 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-43.
DTC No.DTC Detecting ConditionTrouble Area
P1133
P1153
After engine is warmed up, and during vehicle driving at engine
speed 1,400 rpm or more and vehicle speed 60 km/h (38 mph)
or more, if the response characteristic of A/F sensor becomes
deteriorated (2 trip detection logic)
Open or short in A/F sensor circuit
A/F sensor
Air induction system
Fuel pressure
Injector
ECM
WIRING DIAGRAM
Refer to DTC P0125 on page DI-43.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame records
the engine conditions when the malfunction is detected. When troubleshooting, it is useful for determining
whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean
or rich, etc. at the time of the malfunction.
1 Are there any other codes (besides DTC P1133, P1153) being output?
YES Go to relevant DTC chart (See page DI-14).
NO
2 Connect OBDII scan tool or TOYOTA hand-held tester, and read value for volt-
age output of A/F sensor.
PREPARATION:
(a) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(b) Warm up the A/F sensor with the engine speed at 2,500 rpm for approx. 90 sec.
CHECK:
Read the voltage of the A/F sensor on the screen of the OBD II scan tool or TOYOTA hand-held tester when
you perform all the following conditions.
DI2H8-03
Page 1003 of 1897
A11663
VV1, VV2 and NE Signal Waveforms2 V
/Division
20 msec./Division (Idling)
VV1
NE VV2GND
GND
GND
DI-124
- DIAGNOSTICSENGINE
280 Author: Date:
2001 AVALON (RM808U)
DTC P1345 VVT Sensor/Camshaft Position Sensor Cir-
cuit Malfunction (Bank 1)
DTC P1350 VVT Sensor/Camshaft Position Sensor Cir-
cuit Malfunction (Bank 2)
CIRCUIT DESCRIPTION
VVT sensor (VV signal) consists of a magnet, iron core and pickup coil.
The VV signal plate has 3 teeth on its outer circumference and is installed the camshaft timing gear.
When the camshafts rotate, the protrusion on the signal plate and the air gap on the pickup coil change,
causing fluctuations in the magnetic field and generating an electromotive force in the pickup coil.
The actual camshaft angle is detected by the VVT sensor and it provides feedback to the ECM to control
the intake valve timing in response to during condition.
DTC No.DTC Detecting ConditionTrouble Area
No VVT sensor (Camshaft position sensor) signal to ECM
during cranking at 4 sec. or more
Open or short in VVT sensor (camshaft position sensor) cir-
P1345
P1350No VVT sensor (Camshaft position sensor) signal to ECM with
5 sec. or more engine speed 600 rpm or morecuit
VVT sensor (camshaft position sensor)
Camshaft timing gearP1350
While crankshaft rotates twice, VVT sensor (Camshaft position
sensor) signal will be input to ECM 5 times.Camshaft timing gear
ECM
WIRING DIAGRAM
Refer to DTC P0335 on page DI-67.
INSPECTION PROCEDURE
HINT:
If DTC P1345 is displayed, check left bank VVT sensor (camshaft position sensor).
If DTC P1350 is displayed, check right bank VVT sensor (camshaft position sensor).
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
1 Check resistance of VVT sensor (See page IG-7).
Reference: INSPECTION USING OSCILLOSCOPE
During idling, check the waveforms between terminals VV1 and
NE+, and VV2 and NE- of the ECM connector.
HINT:
The correct waveforms are as shown.
The waveform frequency is shortened as the engine
speed becomes higher.
NG Replace VVT sensor.
DI6T9-01
Page 1006 of 1897
A07621A09776
Right Bank OCV
1
2R-B
RECM
OC1+
OC1-
OC2+
OC2- 29
18 Left Bank OCV
R-WR-L 1
2E46
5
E4
E4
E4
- DIAGNOSTICSENGINE
DI-127
283 Author: Date:
2001 AVALON (RM808U)
DTC P1349 VVT System Malfunction (Bank 1)
DTC P1354 VVT System Malfunction (Bank 2)
CIRCUIT DESCRIPTION
VVT system controls the intake valve timing to proper timing in response to driving condition.
ECM controls Oil Control Valve (OCV) to make the intake valve timing properly, and, oil pressure controlled
with OCV is supplied to the VVT controller, and then, VVT controller changes relative position between the
camshaft and the crankshaft.
DTC No.DTC Detecting ConditionTrouble Area
P1349
P1354
Condition (a) or (b) continues for after the engine is warmed up
and engine speed at 400 - 4,000 rpm:
(a) Valve timing does not change from of current valve timing
(b) Current valve timing is fixedValve timing
OCV
VVT controller assembly
ECM
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC P1349 is displayed, check left bank VVT system circuit.
If DTC P1354 is displayed, check right bank VVT system circuit.
Read freeze frame data using TOYOTA hand-held tester or OBD II scan tool. Because freeze frame
records the engine conditions when the malfunction is detected. When troubleshooting, it is useful for
determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel
ratio was lean or rich, etc. at the time of the malfunction.
DI6TB-01
Page 1030 of 1897
DI07B-20
DI-14
- DIAGNOSTICSENGINE
170 Author: Date:
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for the codes listed
in the table below. For details of each code, turn to the page referred to under the ''See page '' for the respec-
tive ''DTC No.'' in the DTC chart.
SAE CONTROLLED
DTC No.
(See page)Detection ItemTrouble AreaMIL*1Memory
P0100
(DI-23)Mass Air Flow Circuit Malfunc-
tionOpen or short in mass air flow meter circuit
Mass air flow meter
ECM
P0101
(DI-27)Mass Air Flow Circuit Range/
Performance ProblemMass air flow meter
P0110
(DI-28)Intake Air Temp. Circuit Malfunc-
tionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor (built into mass air flow meter)
ECM
P0115
(DI-32)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM
P0116
(DI-36)Engine Coolant Temp. Circuit
Range/Performance ProblemCooling system
Engine coolant temp. sensor
P0120
(DI-38)Throttle/Pedal Position Sensor/
Switch ºAº Circuit MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM
P0121
(DI-42)Throttle/Pedal Position Sensor/
Switch ºAº Circuit Range/Perfor-
mance Problem
Throttle position sensor
P0125
(DI-43)Insufficient Coolant Temp. for
Closed Loop Fuel Control
Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
A/F sensor (bank 1, 2 sensor 1)
Air induction system
Fuel pressure
Injector
Gas leakage on exhaust system
ECM
P0128
(DI-48)Thermostat Malfunction
Thermostat
Cooling system
Engine coolant temp. sensor
ECM
P0136
(DI-49)Oxygen Sensor Circuit Malfunc-
tion (Bank 1 Sensor 2)Open or short in heated oxygen sensor circuit
Heated oxygen sensor
P0141
(DI-51)Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 2)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM
Page 1033 of 1897
- DIAGNOSTICSENGINE
DI-17
173 Author: Date:
MANUFACTURER CONTROLLED
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P1130
(DI-106)A/F Sensor Circuit Range/Perfor-
mance Malfunction (Bank 1 Sen-
sor 1)
Open or short in A/F sensor circuit
A/F sensor
Air induction system
Fuel pressure
Injector
ECM
P1133
(DI-1 11)A/F Sensor Circuit Response
Malfunction (Bank 1 Sensor 1)
Open or short in A/F sensor circuit
A/F sensor
Air induction system
Fuel pressure
Injector
ECM
P1135
(DI-1 15)A/F Sensor Heater Circuit Mal-
function (Bank 1 Sensor 1)Open or short in heater circuit of A/F sensor
A/F sensor heater
ECM
P1150
(DI-106)A/F Sensor Circuit Range/Perfor-
mance Malfunction (Bank 2 Sen-
sor 1)
Same as DTC No. P1130
P1153
(DI-1 11)A/F Sensor Circuit Response
Malfunction (Bank 2 Sensor 1)Same as DTC No. P1133
P1155
(DI-1 15)A/F Sensor Heater Circuit Mal-
function (Bank 2 Sensor 1)Same as DTC No. P1135
P1300
(DI-1 17)Igniter Circuit Malfunction (No.1)
Ignition system
Open or short in IGF1 or IGT1 circuit from No.1 ignition coil
with igniter to ECM
No.1 ignition coil with igniter
ECM
P1305
(DI-1 17)Igniter Circuit Malfunction (No.2)
Ignition system
Open or short in IGF2 or IGT2 circuit from No.2 ignition coil
with igniter to ECM
No.2 ignition coil with igniter
ECM
P1310
(DI-1 17)Igniter Circuit Malfunction (No.3)
Ignition system
Open or short in IGF2 or IGT3 circuit from No.3 ignition coil
with igniter to ECM
No.3 ignition coil with igniter
ECM
P1315
(DI-1 17)Igniter Circuit Malfunction (No.4)
Ignition system
Open or short in IGF1 or IGT4 circuit from No.4 ignition coil
with igniter to ECM
No.4 ignition coil with igniter
ECM
P1320
(DI-1 17)Igniter Circuit Malfunction (No.5)
Ignition system
Open or short in IGF2 or IGT5 circuit from No.5 ignition coil
with igniter to ECM
No.5 ignition coil with igniter
ECM
P1325
(DI-1 17)Igniter Circuit Malfunction (No.6)
Ignition system
Open or short in IGF1 or IGT6 circuit from No.6 ignition coil
with igniter to ECM
No.6 ignition coil with igniter
ECM
Page 1251 of 1897
AB0119
I11584
I11584
ON
1
I11585
2
1
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-545
701 Author: Date:
2001 AVALON (RM808U)
INSPECTION PROCEDURE
1 Check voltage between terminal 1 of luggage compartment door key lock and
unlock switch connector and body ground.
PREPARATION:
(a) Remove luggage compartment door trim.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal 1 of luggage compartment
door key lock and unlock switch connector and body ground,
when the key is turned to the unlock side and not turned respec-
tively.
OK:
Key operationVoltage
Turned to the unlock side0 V
Not turnedBattery positive voltage
OK Check and replace theft deterrent ECU.*1
NG
2 Check luggage compartment door key lock and unlock switch.
PREPARATION:
Disconnect luggage compartment door key lock and unlock
switch connector.
CHECK:
Check continuity between terminals 1 and 2, when the key is
turned to the unlock side and not turned respectively.
OK:
Key operationTester connectionSpecified condition
Turned to unlock1 - 2Continuity
Not turned-No continuity
NG Repair or replace luggage compartment door
key lock and unlock switch.
OK